READ THESE INSTRUCTIONS AND AND SAVE THEM FOR FUTURE USE Installation Guide For Models: RS54BNK6LR RS54EB6LR Table of Contents: Safety Tips. pg. 1 Unpacking Your Fan. pg. 2 Parts Inventory. pg. 2 Installation Preparation. pg. 3 Hanging Bracket Installation. pg. 3 Fan Assembly. pgs. 4 - 5 Wiring. pg. 5 Canopy Assembly. pg. 6 Blade Assembly. pg. 6 Light Kit Assembly. pg. 7 Automated Learning Process./ Activating Code. pg. 7 Remote Control Operation. pg. 8 Testing Your Fan. pg. 8 Troubleshooting. pg.
SAFETY TIPS. WARNING: To reduce the risk of electrical shock, turn off the electricity to the fan at the main fuse box or circuit panel before you begin the fan installation or before servicing the fan or installing accessories. 1. READ ALL INSTRUCTIONS AND SAFETY INFORMATION CAREFULLY BEFORE INSTALLING YOUR FAN AND SAVE THESE INSTRUCTIONS. CAUTION: To avoid personal injury, the use of gloves may be necessary while handling fan parts with sharp edges. 2.
1. Unpacking Your Fan. Carefully open the packaging. Remove items from Styrofoam inserts. Remove motor housing and place on carpet or Styrofoam to avoid damage to finish. Do not discard fan carton or Styrofoam inserts should this fan need to be returned for repairs. Check against parts inventory that all parts have been included. 2. Parts Inventory. a. canopy. 1 piece a b d e c b. hanging bracket (pre-attached to canopy).1 piece c. downrod and hanging ball (with pin and clip). 1 piece f d.
3. Installation Preparation. To prevent personal injury and damage, ensure that the hanging location allows the blades a clearance of 7 feet (2.13m) from the floor and 30in. (76cm) from any wall or obstruction. This fan is suitable for room sizes up to 400 square feet (37.2 square meters). 12ft. - 20ft. (3.66m - 6.1m) blade edge 30 7 feet inches (2.13 m) (76 cm) This fan can be mounted with a downrod on a regular (no-slope) or vaulted ceiling.
. Fan Assembly. If you wish to extend the hanging length of your fan, you must remove the hanging ball from the downrod provided to use with an extended downrod (sold separately). [If you wish to use the downrod provided, please proceed to instructions following the dotted line below.] To remove hanging ball, loosen set screw on hanging ball and remove the pin and clip. Lower hanging ball and remove stop pin.
5. Fan Assembly. (cont.) With the hanging bracket secured to the outlet box and able to support the fan you are now ready to hang your fan. Grab the fan firmly with two hands. Slide downrod through opening in hanging bracket and let hanging ball rest on the hanging bracket. Turn the hanging ball slot until it lines up with the hanging bracket tab. hanging bracket tab hanging ball slot WARNING: Failure to align slot in hanging ball with tab in hanging bracket may result in serious injury or death.
. Canopy Assembly. Raise canopy to hanging bracket, aligning slotted holes in canopy with loosened screws in hanging bracket. Twist canopy to lock. Insert screws (along with star washers) previously removed (on page 3, Section 4) and secure all screws with a Phillips screwdriver. hanging bracket slotted hole canopy 8. Blade Assembly. WARNING: To reduce the risk of serious bodily injury, DO NOT use power tools to assemble the blades. If overtightened, blades may crack and break.
motor housing 9. Light Kit Assembly. Remove glass shade from light kit fitter. fitter plate Remove 1 screw from post located on underside of fitter plate and partially loosen the other 2 screws. molex connections Connect WHITE wire from motor housing to WHITE wire from light kit fitter. Connect BLACK (or BLUE) wire from motor housing to BLACK wire from light kit fitter. Be sure molex connections snap together securely.
11. Remote Control Operation. 3 button 2 button 1 button 0 button button for fan HIGH speed for fan MEDIUM speed for fan LOW speed to turn fan OFF to turn light ON or OFF Tap button quickly to turn lights off or on. Hold button down to increase or decrease lights. If you press button in excess of 0.7 seconds, it becomes a dimmer. The lights vary cyclically in 0.8 seconds. The light button has an auto resume function, which keeps the light at the same brightness as the last time it was turned off.
Troubleshooting. Warranty. WARNING: Failure to disconnect power supply prior to troubleshooting any wiring issues may result in serious injury. LITEX 30-YEAR LIMITED WARRANTY: LITEX INDUSTRIES, LTD. warrants this fan to the original household purchaser for indoor use under the following provisions: 1-YEAR WARRANTY: LITEX INDUSTRIES, LTD. will replace or repair any fan which has faulty performance due to a defect in material or workmanship.
