READ THESE INSTRUCTIONS AND SAVE THEM FOR FUTURE USE Installation Guide For model: C-PB42SN5L Table of Contents: Safety Tips. pg. 1 Unpacking Your Fan. pg. 2 Parts Inventory. pg. 2 Installation Preparation. pg. 3 Hanging Bracket Installation. pg. 3 Blade Assembly. pg. 4 Fan Assembly. pgs. 4 - 5 Wiring. pg. 6 Canopy Assembly. pg. 6 Light Kit Assembly. pg. 7 Testing Your Fan. pg. 7 Troubleshooting. pg. 8 Parts Replacement. pg. 8 Warranty. pg. 8 4009654 net weight of fan: 11.93 lb. (5.
SAFETY TIPS. WARNING: To reduce the risk of electrical shock, turn off the electricity to the fan at the main fuse box or circuit panel before you begin the fan installation or before servicing the fan or installing accessories. 1. READ ALL INSTRUCTIONS AND SAFETY INFORMATION CAREFULLY BEFORE INSTALLING YOUR FAN AND SAVE THESE INSTRUCTIONS. CAUTION: To avoid personal injury, the use of gloves may be necessary while handling fan parts with sharp edges. 2. 3. 4.
1. Unpacking Your Fan. Carefully open the packaging. Remove items from Styrofoam inserts. Remove motor housing and place on carpet or Styrofoam to avoid damage to finish. Do not discard fan carton or Styrofoam inserts should this fan need to be returned for repairs. Check against parts inventory that all parts have been included. 2. Parts Inventory. a c b a. hanging bracket (pre-attached to canopy). 1 piece b. canopy. 1 piece d c. downrod and hanging ball (with pin & clip). 1 piece e d.
3. Installation Preparation. To prevent personal injury and damage, ensure that the hanging location allows the blades a clearance of 7ft. (2.13m) from the floor and 30in. (76cm) from any wall or obstruction. This fan is suitable for room sizes up to 144 square feet (13.4 square meters). This fan can be mounted with a downrod on a regular (no-slope) or vaulted ceiling. The hanging length can be extended by purchasing a longer downrod (0.5in./1.27cm diameter).
. Blade Assembly. decorative nuts Locate 15 blade attachment screws/washers and 15 decorative nuts in one of the hardware packs. Take special note of labels on blades and blade arms indicating THIS SIDE UP and refer to drawing at right as needed for the following paragraph. blade arm screw lock washer blade THIS SIDE UP (label) Place underside of blade arm on TOPSIDE of blade and align holes as shown. Insert 3 decorative nuts into holes in blade from UNDERSIDE (i.e.
. Fan Assembly. (cont.) nut vice Remove vice from safety cable by loosening the screw and nut on the vice. Loosen yoke set screws and nut at top of motor housing. Tip: To prepare for threading electrical wires through downrod, apply a small piece of electrical tape to the ends of the electrical wires--this will keep the wires together when threading them through the downrod. downrod Remove pin and clip from downrod (if you have not already done so). Slide downrod through canopy.
. Wiring. WARNING: Turn off circuit breakers to current fixture from breaker panel and be sure switch is turned to the OFF position. white supply wire CAUTION: Be sure outlet box is properly grounded and that a ground wire (GREEN or Bare) is present. Make sure all electrical connections comply with Local Codes or Ordinances and the National Electrical Code.
9. Light Kit Assembly. motor housing Install one 6.5 watt medium base LED bulb (included). IMPORTANT: When replacing bulb, please allow bulb and glass shade to cool down before touching. Align grooves on glass shade with nodules on inside edge of light kit fitter and push up gently on glass shade. Twist glass shade to the RIGHT (clockwise) until glass shade locks into place. Pull down VERY GENTLY on glass shade to make sure that glass shade is secure. bulb glass shade 10. Testing Your Fan.
Troubleshooting. Warranty. WARNING: Failure to disconnect power supply prior to troubleshooting any wiring issues may result in serious injury. LITEX LIFETIME LIMITED WARRANTY: LITEX INDUSTRIES, LTD. warrants this fan to the original household purchaser for indoor use under the following provisions: 1-YEAR WARRANTY: LITEX INDUSTRIES, LTD. will replace or repair any fan which has faulty performance due to a defect in material or workmanship.
