READ THESE INSTRUCTIONS AND SAVE THEM FOR FUTURE USE Installation Guide For Model: BRC30WW6L Table of Contents: Safety Tips. pg. 1 Unpacking Your Fan. pg. 2 Parts Inventory. pg. 2 Installation Preparation. pg. 3 Hanging Bracket Installation. pg. 3 Preparation for Wiring. pg. 4 Wiring. pg. 4 Fan Assembly. pg. 5 Motor Housing Assembly. pg. 5 Blade Assembly. pg. 6 Light Kit Assembly. pg. 7 Testing Your Fan. pg. 7 Troubleshooting. pg. 8 Parts Replacement. pg. 8 Warranty. pg. 8 E124404 net weight of fan: 9.
SAFETY TIPS. WARNING: To reduce the risk of electrical shock, turn off the electricity to the fan at the main fuse box or circuit panel before you begin the fan installation or before servicing the fan or installing accessories. 1. READ ALL INSTRUCTIONS AND SAFETY INFORMATION CAREFULLY BEFORE INSTALLING YOUR FAN AND SAVE THESE INSTRUCTIONS. CAUTION: To avoid personal injury, the use of gloves may be necessary while handling fan parts with sharp edges. 2.
1. Unpacking Your Fan. Carefully open the packaging. Remove items from Styrofoam inserts. Remove motor housing and place on carpet or Styrofoam to avoid damage to finish. Do not discard fan carton or Styrofoam inserts should this fan need to be returned for repairs. Check against parts inventory that all parts have been included. 2. Parts Inventory. a a. hanging bracket. 1 piece b. motor housing. 1 piece b c. motor assembly. 1 piece d. blade arm. 6 pieces c e. glass shade. 1 piece d f. blade.
3. Installation Preparation. 8ft. - 10ft. (2.42m - 3.05m) blade edge 30 inches 7 feet (76cm) (2.13m) To prevent personal injury and damage, ensure that the hanging location allows the blades a clearance of 7 feet (2.13m) from the floor and 30in. (76cm) from any wall or obstruction. This fan is suitable for room sizes up to 100 square feet (9.3 square meters). 8ft. - 10ft. (2.42m - 3.05m) downrod installation flushmount installation This fan can be mounted as a flushmount only on a regular ceiling.
. Preparation for Wiring. hook end Remove single motor mounting screw from hook end of motor assembly. Remove 2 motor mounting screws from hanging bracket. Lift motor assembly to hanging bracket and slide hook end (with single screw hole) into square opening on hanging bracket (see diagram at right). This will allow the motor assembly to hang out of the way while wiring. Tip: Seek the help of another person to hold the stepladder in place and to lift the fan up to you once you are set on the ladder.
7. Fan Assembly. hanging bracket Carefully push wiring and wire connectors into outlet box. Leave hook end of motor assembly in square opening of hanging bracket and lift the other end of motor assembly toward hanging bracket. Align motor assembly screw holes with hanging bracket screw holes and, using motor mounting screws, secure motor assembly with a Phillips screwdriver. motor mounting screws motor mounting screw motor assembly 8. Motor Housing Assembly.
9. Blade Assembly. Time Saver: Washers for blade screws can be set on each blade screw prior to installing blades. motor housing Locate 18 blade attachment screws and washers in one of the hardware packs. Hold blade arm up to blade and align holes. Insert 3 blade attachment screws (along with washers) with fingers first, and then tighten screws securely with a Phillips screwdriver. Repeat procedure for the remaining blades.
10. Light Kit Assembly. motor housing Install 1 medium base 6.5 watt LED bulb (included). Important: When replacing bulb, please allow bulb and glass shade to cool down before touching. switch housing thumbscrew Partially loosen the 3 thumbscrews in the light kit plate. Raise glass shade and hold it in place in the base of the light kit plate. Secure glass shade by tightening the thumbscrews until they touch the rubber ring on the glass shade. Do NOT overtighten thumbscrews as glass may crack or break.
Troubleshooting. Warranty. LITEX 15-YEAR LIMITED WARRANTY: LITEX INDUSTRIES, LTD. warrants this fan to the original household purchaser for indoor use under the following provisions: 1-YEAR WARRANTY: LITEX INDUSTRIES, LTD. will replace or repair any fan which has faulty performance due to a defect in material or workmanship. Contact Litex Customer Service at 1-800-527-1292 to arrange for return of fan. Return fan, shipping prepaid, to Litex Industries, Ltd.
