Instructions / Assembly

A division of
Une division de
Una división de
Copyright © 2020, Liteline Corporation. All rights reserved.
LITELINE CORPORATION
P 416-996-1856 | 1-866-730-7704
F 905-709-5255 | 1-888-738-9736
For more information on our warranty, please visit www.spexlighting.com
Pour plus d'informations sur notre garantie, s'il vous plaît visitez www.spexlighiting.com
Para obtener más información sobre nuestra garantía, visite www.spexlighiting.com
EN
IMPORTANT: Read all instructions before installing
fi xtures. Retain for future reference.
SAFETY: For your safety, this fi xture must be wired in
accordance to local electrical codes and ordinances. All
work should be done by a qualifi ed electrician.
WARNING: Make certain power is OFF from the
electrical panel before starting installation or attempting
any maintenance. Indoor installation only.
TOOLS REQUIRED:
• Drywall saw
• Measuring Tape
• Electrical Wiring (use type and gauge suitable for
application to connect the fi xtures)
ASSEMBLY INSTRUCTIONS:
1. Turn power OFF from the electrical panel before
starting installation.
2. Locate a suitable position to place the fi xture
and open a hole in accordance to the cut-hole
dimensions (refer to Hole Cut Table for appropriate
size).
3. Run the electrical wire from the switch (power
supply) through the mounting hole – use NMD90
Romex or BX cable.
4. Open the hardwire box swing cover and remove the
appropriate knockout(s).
5. Insert the electrical supply cable through the
knockout and secure with a cable connector (sold
separately).
6. Wire box using supplied quick connect push-in
terminals. Connect cable ground wire to bare copper/
green wire on box. Connect white wire of cable to
white wire of box. Connect black wire of cable to
black wire of box [Fig.1].
7. Place all wiring and connections back in to the box
and close the cover
8. New construction applications: Hardwire box shall
be fi rmly secured to studs, joists, or similar fi xed
structural units [Fig. 2].
Remodel applications: Do not require the hardwire
box to be fi rmly secured after the mounting plates,
studs, joists, or structural units that have been
concealed. Insert into ceiling [Fig. 3].
9. Connect hardwire box to fi xture by connecting the
quick disconnect [Fig. 3].
10. Push spring loaded clips on the fi xture upwards and
insert fi xture base in to the mounting hole. Release
the clips and fi xture will be pulled fl ush to the ceiling
[Fig.4].
11. Once assembly is complete, turn on power to
confi rm fi xture is working properly.
1
2
Power supply
Bloc d'alimentation
Black wire
Fil noirWhite wire
Fil blanc
Quick connect push-in terminals
Bornes à bouton
Quick connect push-in terminals
Bornes à bouton
Cable to fi xture
Câble sur le montage
Green wire
Fil vert
Fig. 1
Fig. 3
Fig. 4
Fig. 2
SL-SLMB4-RGBTW-WZ
SL-SLMB6-RGBTW-90WZ
RECESSED LIGHTING • LUMINAIRE ENCASTRE • LÁMPARAS EMPOTRADAS
4" & 6" BAFFLE – RGB + TUNABLE WHITE
BAFFLE 4 PO ET 6 PO – RVB + TUNABLE BLANC
BAFFLE 4 " Y 6 " – RGB + BLANCO SINTONIZABLE
3 YEAR
WARRANTY
GARANTIE
3 ANS
GARANTÍA DE
3 AÑOS
Hole Cut Size / Taille Trou Découpé / Tamaño de
corte del Orifi cio
SL-SLMB4-RGBTW-WZ Ø 4¼ " (108mm)
SL-SLMB6-RGBTW-90WZ Ø 6¼ " (159mm)
REV 10.26.20