IMPORTANT SAFETY INFORMATION A\ Read and understand the manual and safety instructions before assembling, installing, and using Lite boxer Floor Stand. Failure to do so can result in serious injury or death. Save this document. AA WARNING: It is important that Lite boxer Floor Stand is assembled and installed according to the directions provided. If the unit is assembled and or installed incorrectly, it could become insecure, collapse, and cause injury to person and damage to equipment and property.
NOTICES This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device must not cause harmful interference, and (2) this device must not accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
PACKAGE CONTENTS 1. Assembly Packet: memberships card, 2. Pole 3. Accessories Box (A) : gloves, wraps, hard assembly booklet, hardware kit, power supply floor covers, and other optional accessories, Tablet Box (B) and Tablet Arm. 4. Base Liner 6.
LITE BOXER FLOOR STAND DIAGRAM / SPECIFICATIONS Lite shield Uppercut Pad +» Height Adjustment Knob Tablet (Screen and Speakers) Platform \ eo Transport Handle
Prior to unboxing, we recommend designating a space for your Lite boxer. This location will need to have an electrical outlet within 4 feet, and LOCATION REQUIREMENTS ideally should be within close proximity to your wireless router. In addition to the space designated for the platform's footprint, we recommend slaving 12" of clearance in the front and sides of the platform. This additional clearance will allow for any shift in location during your workout.
SETTING UP YOUR LITE BOXER I 1 WATCH THE ASSEMBLY VIDEO: EEA All returns must be shipped in their original packaging. IO] 4 Please save the box and packing material.
oO CHOOSE LITE BOXER PLATFORM: STANDARD OR EXTENDED ® For Standard Platform Installations: CONTINUE to page 10 ~~ —OR— For Extended Platform* Installations: SKIP to page *Note the Platform Extender arrives in a separate box and is purchased separately.
& ASSEMBLE THE PLATFORM | STANDARD 1. Remove shipping insert {A). 2, Slide base halves together (B). 4. Install 8 x base top screws and washers (C). 3. Install 4 x base side screws (D). (sxe to page 12 if you do not have a base extender ) *MAKE THESE TIGHT! peseta =50se I 0=5 mm meme =D tn 0 Tools \ () 10
ASSEMBLE THE PLATFORM | EXTENDED 1. Remove shipping insert {A). 2, Slide base segments together (B). 3. Install 16 x Base Top Screws and Washers (C). Tighten firmly! 4. Install 8 x Base Side Screws {D).
€) CALIBRATE FEET (necessary 1. Ensure the rubber feet beneath the platform are firmly grounded. Raise or lower the feet as needed by rotating them (A). 2. Tighten the nut located above the foot to lock it in place (B). Looking down at the floor, the wrench should rotate counterclockwise for tightening. CAUTION: Lithosphere platform may become unstable and wobble if the feet are not leveled and locked.
0 LAY DOWN THE FLOOR LINER 1. Unroll the Floor Liner {A). If you have a base extender, use the supplied extended floor liner. 2, Set the Floor Liner into the Platform (B).
eo PREPARE THE POLE 1. Extend the Pole fully, then lock in place with the height adjustment handle (A). 2, Fasten the Pole Safety Bracket (B) to the Pole using the two Pole Safety Screws (C). WARNING: To prevent serious injury; A ensure that the Pole Safety Bracket is fully installed & tightened. 3. Pull USB Cables out of both holes EXTEND POLE: » LAY POLE FLAT * LOOSEN HANDLE * FULLY EXTEND POLE * TIGHTEN THE HANDLE TO LOCK EXTENDED POLE. t Pole Safety Bracket Installed.
QO INSTALL THE LITE SHIELD 1. Place Lite shield (A} onto the Pole (B). 2, Install 2 x Lite shield Screws (C) to secure the Lite shield. 3. Connect USB Cable path (D). 4. Insert excess cable into the pole (E). CAUTION: To prevent serious injury Support the weight of the Lite shield before adjusting the height.
oO PREPARE THE TABLET 1. Place the Tablet {A) face down on a non-scratch surface. 2, Fasten the Tablet Arm (B) to the Tablet using four Tablet Screws (C).
0 INSTALL THE TABLET AND CONNECT TO POWER 18 1. Slide the Tablet (A) into the Pole Arm. 2, Fasten the Tablet (A) to the Pole arm using two Tablet Screws (B). 3. Plug in the Lite shield Cable {C) from the pole into the left USB-A port on the tablet. 4. Plug in the Power Cable (D) from the Power Supply (E) into the center USB-C port on the tablet. 5. Organize the cables into the Cable Clips (F). 6. Plug the Power Supply {E) into a wall outlet.
@ ADJUST HEIGHT 1. Adjust the Lite shield to the desired height by supporting its weight (A), then loosening the height adjustment handle (B). We recommend placing the canter “LB” emblem at shoulder-height. 2. Height Adjustment marks are located on the left & right sides of the pole (C). WARNING: To prevent serious injury always support the weight of the Lite shield before adjusting the height.
22 MAINTENANCE AND CARE For more information on keeping your Lite boxer in top shape, go to or scan the OR code below:
WARRANTY For more information on your Lite boxer's warranty, go to or scan the QR code below: 23
24 SUPPORT Should you have any questions or concerns when setting up your Lite boxer, or would like to learn more about assembly, app installation, and the getting started processes, please visit support.liteboxer.
A Read and understand the assembly guide and safety instructions before using your Lite boxer. For more information visit: support.liteboxer.
