WP8721 Access Point LITE-ON User Guide
Content 1 2 3 Introduction...............................................................................................................................3 1.1 Test Bench Setup...........................................................................................................3 RF Test Mode (by RealTek MPTool) ........................................................................................4 2.1 Switch from AP mode to RF test mode ...............................................................
1 Introduction This document describes how to start RF test mode or AP mode, under test firmware. 1.1 Test Bench Setup PC COM GE1 Switch GE1 DUT Console DC Power 1) DUT software version: WP8721_TestFW_Rv0.0.3_20170524 2) COM port configuration: Bits per second / Data bits / Parity / Stop bits / Flow control: 38400/8/None/1/None 3) Power adapter: 802.3at/af PoE or 12V DC 4) DUT default IP address: 192.168.1.254 in AP mode; 192.168.1.6 in RF test mode 5) Configure PC 192.168.1.100.
2 RF Test Mode (by RealTek MPTool) This chapter describes how to start RF test mode (especially continuous TX99 mode). 2.1 Switch from AP mode to RF test mode Please the default mode is AP model, can be switched to RF test mode: In Linux: # # fw_setenv bootcmd 'bootm b04a0000' # reboot Use telnet tool (e.g. putty) to login DUT and input command. Or in u-boot (by serial console tool, e.g.
8197F# setenv bootcmd 'bootm b04a0000'; save; reset 8197F# 2.2 Run MP tool Before running MP tool, make sure ping to 192.168.1.6 is OK. Extract MP-Tool-v3.4-2016.0115.zip, run MP_TEST.exe. 00005076-MP-Tool-v3.4-2016.0115.zip Note: 1. DUT IP address is 192.168.1.6 in RF test mode. 2.3 Continuous Tx As shown in the bellow figure: Dev, channel, bandwidth and ant can be changed. Then click Start to Tx continuously .
Note: 2. 5G Wireless interface is wlan0; 2.4G Wireless interface is wlan1. 3. Ant: A: chain-0; B: chain-1; A+B: chain0+1. 3 AP mode 3.1 Switch from RF test mode to AP mode If current mode is RF test mode, can be switch to AP mode by bellow command. Please note the default mode is AP.
# reboot # Telnet login to 192.168.1.6: Or in u-boot (by serial console tool, e.g. putty): 8197F# 8197F# setenv bootcmd 'bootm b00a0000'; save; reset 8197F# 3.2 Login DUT Input IP address in IE browser “192.168.1.
3.3 Change SSID Take 5G Wifi SSID as example, 5G Wireless Setting is in WLAN1, while 2G Wireless Setting is in WLAN2. 5G default SSID is “RTK 11n AP 5G”, while 2G default SSID is “RTK 11n AP 2.4G”. After Step “ Save & Apply”, there will be 20 seconds for restart wireless.
3.4 Change Channel Take 2G Wifi as example. 2G(WLAN2) default Channel is 11, while 5G(WLAN1) default Channel is 44. After Step “Save & Apply”, there will be 20 seconds for restart wireless.
Note: Channel List 1．2.4G 1,2,3,4,5,6,7,8,9,10,11 2. 5G 36,40,44,48,52,56,60,64,100,104,108,112,149,153,157,161 3.5 Change Mode and Bandwidth Take 2G Wifi as example. 2G(WLAN2) default Band is B/G/N, MCS Mode is HT40, while 5G(WLAN1) default Band is A/AN/AC, MCS Mode is VHT80. After Step “Save & Apply”, there will be 20 seconds to restart wireless.
3.6 Change IP address Bellow figure show how to change DUT IP address if you need to change it.
[End of file]
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
