PRODUCT SPECIFICATION 802.11n, 2T2R Single Band Wireless LAN USB Module WN4616L Version 1.1 User Manual This document contains confidential proprietary information and is property of LTC. The contents of this document should not be disclosed to unauthorized persons without the written consent of LTC.
PRODUCT DESCRIPTION The Wireless LAN USB Module is a sleek miniature Wireless LAN device working under 2.4GHz frequency band. Compatible with IEEE standards, 802.11b, 802.11g and support 802.11n. It provides full functional wireless access within wireless environments anytime, anywhere at a data rate of up to 300Mbps. The WN4616L comes with an USB 2.0 interface providing the maximum transfer rate of 480Mbps, the form factor is an embedded module.
Functional Specifications Standard IEEE802.11b; IEEE 802.11g; IEEE802.11n Bus Interface Universal Serial Bus (USB2.0) Data Rate 802.11b: 11, 5.5, 2, 1 Mbps 802.11g: 54, 48, 36, 24, 18, 12, 9, 6 Mbps 802.11n: MCS 0 to 15 for HT20MHz MCS 0 to 15 for HT40MHz Media Access Control CSMA/CA with ACK Radio Technology 802.11b: CCK, DQPSK, DBPSK 802.11g: 64QAM, 16 QAM, QPSK, BPSK 802.11n: BPSK, QPSK, 16QAM, 64QAM Network architecture Ad-hoc mode (Peer-to-Peer ) Infrastructure mode Operating Channel 2.
ENVIRONMENTAL Operating Operating Temperature: -10 to 75 C (14 to 167 F) Relative Humidity: 5-90% (non-condensing) Storage Temperature: -40 to 85 C (-40 to 185 F) Relevant Humidity: 5-95% (non-condensing) WN4616L Specification Page 4/10 LTC Network Access Confidential 2014/6/27
REGULATORY STATEMENTS FCC Certification The United States Federal Communication Commission (FCC) and the Canadian Department of Communications have established certain rules governing the use of electronic equipment. Part15, Class B This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment. 1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. For product available in the USA market, only channel 1~11 can be operated. Selection of other channels is not possible. IMPORTANT NOTE: This module is intended for OEM integrator.
operation. LABEL OF THE END PRODUCT: The final end product must be labeled in a visible area with the following " Contains TX FCC ID: PPQ-WN4616L ". 完全模組 IMPORTANT NOTE: This module is intended for OEM integrator. The OEM integrator is still responsible for the FCC compliance requirement of the end product, which integrates this module. Appropriate measurements (e.g. 15 B compliance) and if applicable additional equipment authorizations (e.g.
IN NTRODU UCTIO ON Thee 802.11b/g//n 2T2R WLAN W is a ddevice that allows a you connect c youur computerr to a wiireless locall area netwo ork (LAN). A wireless LAN allow ws your systtem to use wireeless Radio Frequency (RF) technnology to traansmit and receive r dataa without phyysically attacching to thee network. T The Wirelesss protocols that come w with this prodduct ensure data securiity and isolaation from interference generated bby other rad dio freqquencies.
e Access Point Netwo ork The Thee network innstallation allows a you tto share files, printers, and a Internett access mucch more connveniently. With Wirelless LAN Cards, C you caan connect w wireless LAN N to a wiredd global nettwork via ann Access Po oint. SO OFTWA ARE INSTALL LATION N Ins stall the device d 1. Make sure the computer is turnedd off. Remov ve the expan nsion slot coover from the t computer. 2.11b/g/n 2T T2R WLAN N into the USB U slot. Puush evenly and 2.
Install the Driver & Utility 1. Exit all Windows programs. Insert the included CD-ROM into your computer. The CD-ROM will run automatically. 2. Manually install driver from Device Manager HARDWARE INSTALLATION Verification To verify if the device exists in your computer and is enabled, go to Start > Control Panel > System (> Hardware) > Device Manager. Expand the Network Adapters category. If the 802.11n Wireless LAN Card is listed here, it means that your device is properly installed and enabled.
