USER MANUAL Wireless Module Model Name: WN4520L Liteon P/N Type A Sony P/N AAZ100426G0 Version 1.0 Author: Kaysa Lee Change History Revision Version 1.0 Date Author Change List 2017/ 07 / 19 Kaysa Lee Initial release * This document contains confidential proprietary information and is property of LTC. The contents of this document should not be disclosed to unauthorized persons without the written consent of LTC.
CONTENT 1 PRODUCT OVERVIEW ...................................................................................................................... 3 1.1 DESCRIPTION ............................................................................................................................. 3 1.2 FEATURES .................................................................................................................................. 3 1.3 GENERAL SPECIFICATIONS ..........................................
1 PRODUCT OVERVIEW 1.1 DESCRIPTION WN4520L is a WLAN module which using Chipsets : Rockchip NanoD and Realtek RTL8821CSH 1.2 FEATURES Operate at 2.4GHz / 5GHz band 150Mbps PHY Rate Support 1T1R Mode 20MHz Bandwidth Support (2.4G) , 20/40MHz Bandwidth Support (5G) IEEE standards support: IEEE 802.11a/b/g and 802.11n 802.11i‐ WEP 64/128, AES, TKIP RoHS compliance Low Halogen compliance 1.3 GENERAL SPECIFICATIONS Main Chipset RTL8821CSH Standard IEEE 802.
Current Consumption Antenna Type 1.4 WN4520L TBD Printed Antenna: 2.4G: 2.5dBi (max peak gain) 5G: 3.
1.
1.
1.7 PCB INFORMATION No. Item 1 PWB Supplier 2 ID Mark 3 PWB Supplier UL File No. 4 PWB Material Supplier 5 PWB Material PWB Material Supplier 6 UL File No. 7 Flame Class Rated Temperature 8 (Max Operation Temp.
1.
FCC WARING STATEMENT FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
the DFS band.
End Product Labeling The final end product must be labeled in a visible area with the following: "Contains FCC ID: PPQ‐WN4520L ” IMPORTANT NOTE: This module is intended for OEM integrator. The OEM integrator is still responsible for 1. ensuring that the end-user has no manual instructions to remove or install module 2. the FCC compliance requirement of the end product, which integrates this module. 3. Appropriate measurements (e.g. 15 B compliance) and if applicable additional equipment authorizations (e.
IC WARING STATEMENT Canada, avis d'Industry Canada (IC) This device complies with Industry Canada’s licence‐exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
OEM integrator is still responsible for testing their end product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). IMPORTANT NOTE: In the event that these conditions cannot be met (for example certain laptop configurations or co‐location with another transmitter), then the IC authorization is no longer considered valid and the IC No. cannot be used on the final product.
Radio Frequency (RF) Exposure Information The radiated output power of the Wireless Device is below the Industry Canada (IC) radio frequency exposure limits. The Wireless Device should be used in such a manner such that the potential for human contact during normal operation is minimized. This device has also been evaluated and shown compliant with the IC RF Exposure limits under mobile exposure conditions. (antennas are greater than 20cm from a person's body).
Japan Statement: 5GHz product for indoor use only. この製品は屋内においてのみ使用可能です CE Statement: Compliance with 2014/53/EU Radio Equipment Directive (RED) In accordance with Article 10.8(a) and 10.8(b) of the RED, the following table provides information on the frequency bands used and the maximum RF transmit power of the product for sale in the EU: Frequency range (MHz) 2400-2483.5 5150-5250 5250-5350 5470-5725 Max.
