PRODUCT SPECIFICATION 802.11a/b/g/n/ac, 2T2R Wireless LAN USB2.0 Module WN4515L Realtek RTL8812AU Version 1.0 User Manual * This document contains confidential proprietary information and is property of LTC.
CONTENT FCC WARING STATEMENT .......................................................................................................... 3 IC WARING STATEMENT .............................................................................................................. 4 PRODUCT FEATURES .................................................................................................................... 6 PRODUCT SPECIFICATIONS ..................................................................................
FCC WARING STATEMENT FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: "Contains FCC ID: PPQ-WN4515L ” Information for the OEMs and Integrators The following statement must be included with all versions of this document supplied to an OEM or integrator, but should not be distributed to the end user.
OEM integrator is still responsible for testing their end product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). IMPORTANT NOTE: In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the IC authorization is no longer considered valid and the IC No. cannot be used on the final product.
The transmitter module may not be co-located with any other transmitter or antenna. Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne. Radio Frequency (RF) Exposure Information The radiated output power of the Wireless Device is below the Industry Canada (IC) radio frequency exposure limits. The Wireless Device should be used in such a manner such that the potential for human contact during normal operation is minimized.
PRODUCT SPECIFICATIONS MAIN CHIPSET MAC/ Baseband/ RF: Realtek 8812AU-VS-CG FUNCTIONAL SPECIFICATIONS WiFi Function Standard IEEE802.11a; IEEE802.11b; IEEE 802.11g; IEEE 802.11n; IEEE802.11ac Bus Interface Universal Serial Bus (USB2.0) Data Rate 802.11a: 54, 48, 36, 24, 18, 12, 9, 6 Mbps 802.11b: 11, 5.5, 2, 1 Mbps 802.11g: 54, 48, 36, 24, 18, 12, 9, 6 Mbps 802.11n: MCS 0 to 15 for HT20MHz MCS 0 to 15 for HT40MHz 802.
Receiver Sensitivity Security 15 dBm@1-11Mbps 802.11g: 14 dBm@6-54Mbps 802.11n(2.4GHz): 20MHz: 13dBm@MCS0-7 40MHz: 13dBm@MCS0-7 802.11n(5GHz): 20MHz: 12dBm@MCS0-7 40MHz: 12dBm@MCS0-7 802.11ac: 20MHz: 13dBm@MCS0-8 40MHz: 12dBm@MCS0-9 80MHz: 11dBm@MCS0-9 802.11a: -85 dBm@6Mbps -70 dBm@54Mbps 802.11b: -83 dBm@11Mbps 802.11g: -86 dBm@6Mbps -70 dBm@54Mbps 802.11n(2.4GHz): 20MHz -69 dBm@MCS7 40MHz -66 dBm@MCS7 802.11n(5GHz): 20MHz -69 dBm@MCS7 40MHz -66 dBm@MCS7 802.
1.35W Unassoci ated Idle Standby @Wake up mode 1.66W 22mA / 0.11W 20mA / 0.1W Metal Antenna on Board Antenna Type RECOMMENDED OPERATION CONDITIONS For Module Symbol VCC Rating 5V Supply Voltage Min Typ Max Units 4.5 5 5.5 V Min Typ Max Units For IC Symbol Rating VDD33 3.3V Supply Voltage 3.0 3.3 3.6 V VDD12 1.2V Supply Voltage 1.10 1.2 1.23 V Min Typ Max Units DC CHARACTERISTICS Symbol Parameter VIL Input Low Voltage - 0 0.9 V VIH Input High Voltage 2.0 3.
PIN ASSIGNMENT Pin. 1 2 3 4 5 6 7 8 Pin Define Description Status +3.3V +3.3V 3.3V source 3.
MECHANICAL Page 11/13
METAL ANTENNA SPEC On Board Antenna for WiFi (Q’ty:1pcs) Page 12/13
EEPROM INFORMATION US Reg Domain 0x25 Vendor ID 0x0BDA Product ID 0x881A ENVIRONMENTAL Operating Operating Temperature: 0 to 70 °C Relevant Humidity: 5-90% (non-condensing) Storage Temperature: -40 to 85 °C (-40 to 185 °F) Relevant Humidity: 5-95% (non-condensing) Page 13/13
