USER MANUAL 802.11n, Dual Band 1T1R Wireless Lan SDIO Module WN3501M Marvell 88w8782 Version 1.2 Change History Revision Version 1.0 Version 1.1 Date 2014/04/30 2014/09/15 Author Kaysa Lee Kaysa Lee Version 1.2 2016/06/20 Kaysa Lee Change List Preliminary Update Product Picture Update: 1.Product Picture Add: 2. 2D drawing 3. Packing drawing 4. FFC Cable Drawing 5. Shielding Drawing 6. MAC Label Drawing * This document contains confidential proprietary information and is property of LTC.
CONTENT PRODUCT FEATURES .................................................................................................................... 3 WI-FI FEATURE: ..................................................................................................................................... 3 PRODUCT SPECIFICATIONS ........................................................................................................ 4 MAIN CHIPSET ..........................................................................
PRODUCT FEATURES WI-FI FEATURE: Operate at ISM frequency Band (2.4/5GHz) IEEE Standards Support, 802.11a,802.11b, 802.11g and 802.11n Support SDIO, G-SPI, high-speed UART interface Enterprise level security supporting: WPA, WPA2, WAPI Support 1 transmission and 1 receiving, transmission rate can up to 150Mbps (Physical Rate) in downstream and upstream Low power consumption Support Linux OS based and kernel up to 2.6.x , Android 2.2/3.
PRODUCT SPECIFICATIONS MAIN CHIPSET Marvell 88w8782 FUNCTIONAL SPECIFICATIONS Wi-Fi Function Standard IEEE802.11a; IEEE802.11b; IEEE 802.11g; IEEE 802.11n Bus Interface SDIO Data Rate 802.11b: 11, 5.5, 2, 1 Mbps 802.11a/g: 54, 48, 36, 24, 18, 12, 9, 6 Mbps 802.11n: MCS 0 to 7 for HT20MHz MCS 0 to 7 for HT40MHz Media Access Control CSMA/CA with ACK 802.11b: CCK, DQPSK, DBPSK 802.11a/g: Modulation Techniques 64QAM, 16QAM, QPSK, BPSK 802.
1 mA Dual Antenna connectors Antenna Type PIN ASSIGNMENT Pin. Pin Define Type 2 GND RESETTn I 3 4 WLAN_LED WAKEUP O I 5 SLP_CLK_In I 1 Description Ground Reset (active low) (internal pull-high) Please keep this pin floating if host don’t need to control it. WLAN LED Host Wakeup: Host-to-SoC Wakeup (input) Please keep this pin floating if host don’t need to control it. Sleep Clock Input Please keep this pin floating if host don’t need to control it.
PRODUCT PICTURE EEPROM INFORMATION Reg Domain FCC Channels 1-11 with active scan Vendor ID 0x02DF Device ID 0x9121 ENVIRONMENTAL OPERATING Operating Temperature: 0 to 70 C (32 to 158F) Relative Humidity: 5-90% (non-condensing) STORAGE Temperature: -40 to 80 C (-40 to 176 F) Relative Humidity: 5-95% (non-condensing) Page 6/11
SHIELDING DRAWING MAC LABEL Page 7/11
FFC CABLE DRAWING Page 8/11
Power UP Sequence PDn must remain asserted for a minimum of 1 ms after VDD33 is stable For auto reference clock detection, the sleep clock (32.
SDIO Protocol Timing Diagram—High Speed Mode SDIO Timing Data Symbol Parameter FPP Clock Frequency TWL Clock Low Time TWH Clock High Time TISU Input Setup Time TIH Input Hold Time TODLY TOH Output Delay Time Output Hold Time Condition Normal High Speed Normal High Speed Normal High Speed Normal High Speed Normal High Speed High Speed Page 10/11 Min 0 0 10 7 10 7 5 6 5 2 2.5 Typ - Max 25 50 7.
PACKING DRAWING (MODULE + FFC CABLE) Page 11/11
FCC Statement: FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
LABEL OF THE END PRODUCT: The final end product must be labeled in a visible area with the following " Contains TX FCC ID: PPQ-WN3501M ". If the labelling area is larger than the palm of the hand, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules.
IC Statement: This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d.
IMPORTANT NOTE: This module is intended for OEM integrator. The OEM integrator is responsible for the compliance to all the rules that apply to the product into which this certified RF module is integrated. Additional testing and certification may be necessary when multiple modules are used. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment.
Japan Statement: 5GHz band (W52, W53): Indoor use only
NCC Statement: (1) 「經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大 功率或變更原設計之特性及功能」。 (2) 「低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用， 並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射 頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾」。 (3) 無線資訊傳輸設備必須具備安全功能，以保護未經授權之一方任意更改軟體進而避免發射機操作於 非經認證之頻率、輸出功率、調變形式或其他射頻參數設定。 (4) 無線資訊傳輸設備避免影響附近雷達系統之操作。 (5) 「本模組於取得認證後將依規定於模組本體標示審驗合格標籤, 並要求平台廠商於平台上標示「本 產品內含射頻模組 CC XX xx LP yyy Z z」。
Korea Statement: B 급기기 (가정용 방송통신기자재) 이 기기는 가정용(B 급) 전자파적합기기로서 주로 가정에서 사용하는 것을 목적으로 하며, 모든 지역에서 사용할 수 있습니다.
