USER R MANU UAL WLAN W +B BT Combo Module Model Nam me: WCB BN4511R R Liteon P/N Hiisense P//N AAZ1 100235D0 WCB BN4511R(62) WCBN4 4511R(62 2‐WOB) WCB BN4511R(32) WCB BN4511R(12) AAZ1 100238D0 AAZ100233D0 AAZ100310D0 V Version 1.2 Autthor: Kaysa Leee Change H History Date e Author Change List Version 11.0 2015 5 / 10 / 10 Kaysa Lee Initial rele ease Version 11.1 2015 5 / 11 / 09 Kaysa Lee Add VID/PID informatio on Version 11.
CONTENT 1 PROD DUCT OVERVIEEW ......................................................................................................................... 3 1.1 DEESCRIPTION ................................................................................................................................ 3 1.2 FEEATURES ..................................................................................................................................... 3 1.3 GEENERAL SPECIIFICATIONS ..........................
1 PRODU UCT OVERVIEW 1.1 DESCRIPTION N WCBN4511R is a WLAN +BT Combo C moduule which using MTK Chip pset MT76622TU 1.2 FEEATURES Operate at 2.4 4GHz / 5GHz band 8666Mbps PHYY Rate Support 2TT2R Mode USSB 2.0 suppo ort for date rates up to 122Mbps full sp peed and 480Mbps high speed IEEE standards support: IE EEE 802.11a//b/g and 802.11n 8002.11i‐ WEP 64/128, AES, TKIP Ro oHS compliance Lo ow Halogen compliance c 1.3 GENERAL SPEECIFICATION NS Maain Chipset MT76 662TU Standard IEEE 802.
Tem mperature & Hum midity Normal Test Condittion: 25 +/‐ 2d deg.C , 65 +/‐ 2% RH Opera ating: ‐10 to 770 deg.C Storagge: ‐40 to 85 ddeg.
1.4 BOARD OUTLLINE 1.
1.6 W WTB USB I//F CONNECTTOR(1.25MM M PITCH) 9pin Man nufacturer : ACES Partt Number : 50271‐009‐‐0N‐001 1.
2 Appeaarance, Marking M 2.1 Appearance Top Botttom 2.
3 Packaage 3.1 Packing Spec S 3.2 Tray Spec 3.
FCC Statement: Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
compliance to all the rules that apply to the product into which this certified RF module is integrated. Additional testing and certification may be necessary when multiple modules are used. 20 cm minimum distance has to be able to be maintained between the antenna and the users for the host this module is integrated into. Under such configuration, the FCC radiation exposure limits set forth for an population/uncontrolled environment can be satisfied.
OEM Integrator Checklist The party below will implement the LITE‐ON Module in host systems in accordance with the instructions specified in this document and the documents referenced herein. 1. The OEM integrator will ensure the Module is integrated in a host systems using only the approved antenna model(s) described in this document. BT：Walsin / RFMTA400536IMAB301 / PIFA Antenna / Gain: 3.79dBi 2.4G：LITE‐ON / WCBN4511R / PIFA Antenna / ANT‐L Gain: 2.54dBi, ANT‐R Gain: 0.
IC Statement: This device complies with Industry Canada license‐exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
Sélection dynamique de fréquences (DFS) pour les dispositifs fonctionnant dans les bandes 5250‐5350 MHz, 5470‐5600 MHz et 5650‐5725 MHz. The maximum antenna gain permitted for devices in the bands 5250‐5350 MHz and 5470‐5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit. le gain maximal d’antenne permis pour les dispositifs utilisant les bandes 5250‐5350 MHz et 5470‐5725 MHz doit se conformer à la limite de p.i.r.e.
user has to be informed that the IC radio‐frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment.
