USER MANUAL WLAN + BT Combo Module Model Name: WCBN4506R Type A Type B Liteon P/N AAZ100162G0 AAZ100171G0 Sony P/N 1‐493‐092‐11 1‐493‐092‐21 Version 1.1 Author: Kaysa Lee Change History Revision Date Author Change List Version 1.0 2015 / 09 / 01 Kaysa Lee Initial release Version 1.1 2015 / 09 / 21 Kaysa Lee Update Product Picture/MAC Label format(size) * This document contains confidential proprietary information and is property of LTC.
CONTENT 1 PRODUCT OVERVIEW ...................................................................................................................... 3 1.1 DESCRIPTION ............................................................................................................................. 3 1.2 FEATURES .................................................................................................................................. 3 1.3 GENERAL SPECIFICATIONS...........................................
1 PRODUCT OVERVIEW 1.1 DESCRIPTION WCBN4506R is a WLAN +BT Combo module which using MTK Chipset MT7662RU 1.2 FEATURES Operate at 2.4GHz / 5GHz band 300Mbps PHY Rate Support 2T2R Mode 20MHz Bandwidth Support (2.4G) , 40MHz Bandwidth Support (5G) USB 2.0 support for date rates up to 12Mbps full speed and 480Mbps high speed IEEE standards support: IEEE 802.11a/b/g and 802.11n 802.11i‐ WEP 64/128, AES, TKIP RoHS compliance Low Halogen compliance 1.
Temperature & Humidity Normal Test Condition: 25 +/‐ 2deg.C , 65 +/‐ 2% RH Operating: ‐10 to 45 deg.C (2x2 mode), ‐10 to 60 deg.C (1x2 mode) Storage: ‐40 to 85 deg.C Operating Voltage 3.3V ±10% I/O supply voltage Current Consumption Antenna Type Typical: 500mA (2x2 mode) Max: 650mA (2x2 mode) Min: 450mA (2x2 mode) Type A: Antenna PWB (WiFi) + IPEX MHF RF connector x 1 (BT) Type B: IPEX MHF RF connector x 3 (WIFI + BT) 1.
1.5 PCB INFORMATION No. 1 Item PWB Supplier 2 ID Mark 3 4 5 PWB Supplier UL File No. PWB Material Supplier PWB Material PWB Material Supplier UL File No. Flame Class Rated Temperature 6 7 8 (Max Operation Temp.) Vendor #1 APCB 323K380024YD 323K381022YD (module) (antenna) E85792 E85792 GRACE Nanya GA‐HF‐15 NPG‐150N Vendor #2 PIOTEK 323K380024AD (module) 323K381022AD (antenna) E220370 Nanya NPG‐150N E186152 E98983 E98983 94V‐0 94V‐0 94V‐0 TG‐150 TG‐150 TG‐150 1.
Frame: 1.7 PIN CONFIGURATION Pin 1 2 3 4 Name GND DM DP RST_L 5 SYNC 6 7 8 VCC VCC GND WCBN4506R UART version 10Pin Type Description ‐ Ground I/O USB Data ‐ I/O USB Data + I Ground SYNC Signal O GPIO11(MT7662RU Pin44) PWR 3.3V PWR 3.
1.8 WARNINGS FCC Statement: Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. IMPORTANT NOTE: This module is intended for OEM integrator. The OEM integrator is responsible for the compliance to all the rules that apply to the product into which this certified RF module is integrated.
IC Statement: This device complies with Industry Canada license‐exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
Dynamic Frequency Selection (DFS) for devices operating in the bands 5250‐ 5350 MHz, 5470‐5600 MHz and 5650‐5725 MHz. Sélection dynamique de fréquences (DFS) pour les dispositifs fonctionnant dans les bandes 5250‐5350 MHz, 5470‐5600 MHz et 5650‐5725 MHz. The maximum antenna gain permitted for devices in the bands 5250‐5350 MHz and 5470‐5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit.
Table for Filed Antenna Set Ant. Brand Holder Model Name Antenna Type Connector 1 SONY corporation WCBN4506R PIFA Antenna N/A 2 SONY corporation WCBN4506R PIFA Antenna N/A 3 SONY corporation WCBN4506R Dipole Antenna I‐PEX 4 SONY corporation WCBN4506R Dipole Antenna I‐PEX 01S1072‐00 Dipole Antenna I‐PEX 01S1072‐00 Dipole Antenna I‐PEX 1 2 Waka manufacturing Co.,Ltd. Waka manufacturing Co.,Ltd. 5 3 6 Gain (dBi) WiFi‐5GHz WiFi‐5GHz Band 2 Band 3 1.81 2.14 1.78 2.12 Set Ant.
2.
I‐PEX Plug : Smooth Insert Type 3. The EUT has three sets of antennas and there are two antennas for each set. 4. Set 2~3 are the same type antenna. Only the highest gain antenna (Set 2 for Bluetooth, 5G Band3, Set 3 for 2.4G, 5G Band 1, 2, 4) was selected to test and record in this report.
This module is intended for OEM integrator. The OEM integrator is still responsible for the IC compliance requirement of the end product, which integrates this module. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. USERS MANUAL OF THE END PRODUCT: In the users manual of the end product, the end user has to be informed to keep at least 20 cm separation with the antenna while this end product is installed and operated.
Japan Statement: 5GHz product for indoor use only. CE Statement: This equipment complies with EU radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body.
