User's Manual Part 1

USERS MANUAL OF THE END PRODUCT:
The end user has to be informed that the FCC radio-frequency exposure guidelines for an
uncontrolled environment can be satisfied. The end user has to also be informed that any
changes or modifications not expressly approved by the manufacturer could void the user's
authority to operate this equipment. If the size of the end product is smaller than 8x10cm, then
additional FCC part 15.19 statement is required to be available in the users manual: This device
complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference and (2) this device must accept any interference
received, including interference that may cause undesired operation.
LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains TX
FCC ID: PPQ-WB110C/PPQ-WB110CIW ". If the size of the end product is larger than
8x10cm, then the following FCC part 15.19 statement has to also be available on the
label: This device complies with Part 15 of FCC rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference and (2) this
device must accept any interference received, including interference that may cause
undesired operation.
Hereby, Lite-On, declares that this device is in compliance with the essential requirement and
other relevant provisions of the R&TTE Driective 1999/5/EC. “ ᆖীڤᎁᢞٽ௑հ܅פ෷୴᙮ሽ
ᖲΔᆖ๺ױΔֆ׹Ε೸ᇆࢨࠌش݁լ൓ᖐ۞᧢ޓ᙮෷ΕףՕפ෷ࢨ᧢ޓ଺๻ૠհ௽ࢤ֗פ౨Ζ
܅פ෷୴᙮ሽᖲհࠌشլ൓ᐙ᥼ଆ౰ڜ٤֗եឫٽຏΙᆖ࿇෼ڶեឫ෼ွழΔᚨمܛೖشΔࠀ
ޏ࿳۟ྤեឫழֱ൓ᤉᥛࠌشΖছႈٽຏΔࠉሽ๵ࡳ܂ᄐհྤᒵሽຏΖ܅פ෷୴᙮ሽ
ᖲႊݴ࠹ٽຏࢨՠᄐΕઝᖂ֗᠔᛭شሽᘿ୴ࢤሽᖲ๻ໂհեឫΖ”ءᑓิ࣍࠷൓ᎁᢞ৵ലࠉ
๵ࡳ࣍ᑓิء᧯ᑑقᐉ᧭ٽ௑ᑑ᧘, ࠀ૞ޣؓ؀ᐗ೸࣍ؓ؀Ղᑑقψءข঴փܶ୴᙮ᑓ CC XX xx
YY yyy Z z WڗᑌΔᇡาᇷறᓮ೶ەࠌشᎅࣔ஼Ζ ءֆ׹բ࣍ᎅࣔ஼խ༼ࠎࢬڶؘ૞ᇷಛאᖄ
ࠌش/ڜᇘإᒔڜᇘ֗ᖙ܂Ζ
The module will only be sold to and installed by appointed OEM or ODM installers.