User's Manual

Step 3: Check the LED status
Power LED: The table below describes the states of the Power LED.
Troubleshooting
1. Ensure that the Ethernet cable is correctly plugged into the LAN1 (POE) port on the O-105ER and the other
end of the cable is plugged into an Ethernet jack or a port on a switch that is turned ON.
2. If the O-105ER did not receive a valid IP address from the DHCP server, ensure that a DHCP server is ON and
available on the VLAN/subnet to which the AP is connected. If the AP still fails to get a valid IP address, you
can reboot it once to see if that resolves the problem.
3. If you are using Arista Cloud Services, make sure that Internet connectivity is available from the VLAN/subnet
to which the AP is connected. Check if the required ports for AP and Server communication – UDP 3851
and default HTTP (TCP port 80) – are open on the Firewall. If you are using a Proxy, Web accelerator or URL
Reduced capability indicates that the AP is getting lower than the
required maximum power from the PoE switch, i.e., 802.3af instead
of 802.3at.
LAN LEDs: ON when the corresponding link is up.
Radio LEDs: ON when the corresponding radio is operational.
Green Orange
Solid Running at full capability Running at reduced
capability
Blinking Received IP address, but
not connected to the
server
Did not receive an IP
address
5453 Great America Parkway
Santa Clara, CA 95054
USA
408 547-5500
www.arista.com
Arista, Mojo, the Arista logo, and the Mojo logo are trademarks or registered trademarks of
Arista Networks, Inc. and Mojo Networks, LLC. in the U.S. and other countries.
© 2020 Arista Networks, Inc. www.arista.com
Headquarters
408 547-5500
www.arista.com
Support
408 547-5502
866 476-0000
[e-mail]
Sales
408 547-5501
866 497-0000
[e-mail]
00182-02
Our social responsibility includes conducting business in a manner that minimizes our ecological impact on the
environment and reducing waste in our supply chain. To that end, the Quick Start Guide and Safety Manual are available
at www.arista.com.
Getting Started
are available at
http://www.arista.com/en/support/product-documentation
Other documents available at this location include:
You can access Arista documentation at
https://www.arista.com/en/support
Documents available at this location include:
• Wireless Manager Appliance Quick Start Guide
• Safety and Compliance Guide
• WiFi Regulatory Compliance Statements
• User Manual
You may also download current software, as well as view FAQs, Warranty Information, Knowledge Base articles, Security
Advisories, Software Licenses, and Field Notices at https://www.arista.com/en/support
Receiving and Inspecting the Equipment
Upon receiving the access point, inspect the shipping boxes and record any external damage. Retain the packing
materials if you suspect that part of the shipment is damaged; the carrier may need to inspect them.
If the boxes were not damaged in transit, unpack them carefully. Ensure that you do not discard any accessories that
may be packaged in the same box as the main unit.
Obtaining Technical Assistance
Customers, partners, resellers, or distributors holding a valid Arista Service Contract can obtain technical support
through these sources:
Email:
. This is the easiest way to create a new service request.
Include a detailed description of the problem and the output of “show tech-support”.
Web: www.arista.com/en/support.
A support case may be created through the support portal on our website.
Pole Mount: Jio logo facing away from the pole
Note:
personal who has RF and related knowledge.
Getting the O-105ER Online
Step 1: Power up
Plug one end of the Ethernet cable into the PoE+ switch or injector and plug the other end into the LAN1
(PoE) on the O-105ER. Make sure the PoE+ source you are using is turned ON.
Step 2: Connect to the network
As you are using PoE+, the O-105ER should already be connected to your network.
Philips #2 screwdriver
External Antennas: Make sure the antennas are connected to their respective “N-type” connector ports
shown below.
O-105ER Access Point Getting Started Guide
Package Contents
You should have received the following components in your O-105ER package.
Wall Mount: Jio logo facing away from the wall
Mounting the O-105ER
Mounting Accessories
O-105ER
Mounting Bracket
Metal Clamp
x 4
x 1
x 2
x 4
x 4 x 1
x 2
F
For
earthing
in the bracket
Black
sealing
pins
50mm
Drill location Insert four anchors
Philips #2 screwdriver
Length ≥100mm
Ø 6.5mm (Depth 30mm)
84mm
for WP9331E-RJIO
正面 背面
成型方式:
QSG
5153*
210mm
298mm
(客戶):Arista
(材質): 128g雙銅紙
(顏色):CMYK
(表面處理): NO
(展開尺寸):298x210mm
(成型尺寸):149x210mm
(公差):+-1mm
A3
Dereck
蔣飛龍
2020-01-10
WI-RDC-016
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a resi-
dential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful inter-
ference to radio or television reception, which can be determined by turning the equipment off and on, the user is en-
couraged to try to correct the interference by one of the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
● Consult the dealer or an experienced radio/TV technician for help.
FCC
Caution: Any changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This de-
vice may not cause harmful interference, and (2) this device must accept any interference received, including inter-
ference that may cause undesired operation.
Professional installation is required
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equip-
ment should be installed and operated with minimum distance 20cm between the radiator & your body.