User's Manual

ManualsBrandsLITE-ON Technology ManualsElectronicsZigbee Module

MZ0100S-1 Product Specification Page 1/9

LTC Network Access Confidential

PRODUCT REQUIREMENT SPECIFICATION

MZ0100S-1

ZigBee Module

Version 1.2

Author: Javon Tseng Editor: Javon Tseng

Project Leader: Daniel KW Yang Approved by: Daniel KW Yang

Change History

Revision Date Author Change List

1 Nov, 01, 2014 Javon Tseng Initial

1.1 Dec. 31, 2014 Jesse Yang Added PA feature

1.2 Apr.26, 2015 Rocky Chen Update

* This document contains confidential proprietary information and is property of LTC. The contents of

this document should not be disclosed to unauthorized persons without the written consent of LTC.

Summary of content (9 pages)

PAGE 1
PRODUCT REQUIREMENT SPECIFICATION MZ0100S-1 ZigBee Module Version 1.2 Author: Javon Tseng Editor: Javon Tseng Project Leader: Daniel KW Yang Approved by: Daniel KW Yang Change History Revision 1 1.1 1.2 Date Nov, 01, 2014 Dec. 31, 2014 Apr.26, 2015 Author Javon Tseng Jesse Yang Rocky Chen Change List Initial Added PA feature Update * This document contains confidential proprietary information and is property of LTC.
PAGE 2
CONTENT 1 PRODUCT OVERVIEW.................................................................................................................3 1.1 DESCRIPTION ........................................................................................................................3 1.2 FEATURES .............................................................................................................................3 1.3 GENERAL SPECIFICATIONS ............................................................
PAGE 3
1 Product Overview 1.1 Description The MZ0100S-1, ZigBee Module is using 32-bit ARM® Cortex®-M3 microprocessor and an integrated ultra-low power 2.4GHz ISM band, compliance with IEEE 802.15.4 transceiver. These ZigBee Module is available in 33-pin stamp holes packages with up to 512KB Flash, and 64KB of SRAM. MZ0100S is based on SILICON LABS EM3585 single chip ZigBee solution the Wireless sensor networking, Industrial control, Machine-to-Machine (M2M) and emerging Internet of Things (IoT) markets. 1.
PAGE 4
Antenna Type 1. Print Antenna 2.
PAGE 5
2. Pin Assignment and Description Pin Number 1 2 3 4 5 6 7 8 9 10 Module Pin Name GND GND NC nRST PC6 PC7 PA7 PB3 PB4 PA0 11 Pin Description Ground Ground NC Reset Pin. Active Low Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O I/O P P -I I/O I/O I/O I/O I/O I/O PA1/I2C_SDA Digital I/O.
PAGE 6
Liteon Type A module Dimension : 24 x 17 x 2.5mm 3.
PAGE 7
FCC WARING STATEMENT This equipment has been tested and found to comply with the limit s for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 8
2. Only those antennas with same type and lesser gain filed under this FCC ID number can be used with this device. 3. The regulatory label on the final system must include the statement: “Contains FCC ID: PPQ-MZ0100S1 “. 4. The final system integrator must ensure there is no instruction provided in the user manual or cu stomer documentation indicating how to install or remove the transmitter module except such devic e has implemented two‐ways authentication between module and the host system.
PAGE 9
IC WARING STATEMENT Canada, Industry Canada (IC) Notices This Class B digital apparatus complies with Canadian ICES-003 and RSS-247. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Canada, avis d'Industry Canada (IC) Cet appareil numerique de classe B est conforme aux normes canadiennes ICES-003 et RSS-247.