Fusion 70 Access Point Installation Guide Part Number: 001605, Rev.
001605, Rev.
Introduction Introduction The Fusion 70 Access Point is a reliable, high-speed wireless device that offers secure communication access for both voice and data IEEE 802.11n transmissions for any SMB (Small- to Medium-sized Business). With a frequency of 2.4 GHz (802.11 b/g/n), this innovative and costeffective AP provides clients a fast and reliable network connection. You can provide power to the access point either by using a single, standard IEEE 802.
Introduction Product Description Features Table 2 Item Feature Description 1 LEDs These three indicators display power and/or link activity. 2 Console Port This port provides a serial interface for the AP. 3 Reset Button This button provides a mechanism to allow you to restore the AP back to its factory default settings. 4 Desktop Slots These slots allow you to mount the unit to a bracket (included), so that you can stand it up on a desktop.
Introduction Power and Environmental Power and Environmental Table 3 Input voltage AC power Operating 90-264 V AC Frequency 47-63 Hz Operating Temperature 32 to 104ºF (0-40C) Relative Humidity 5% to 95% (non-condensing) LEDs The Fusion 70 Access Point has the following three LEDs on to provide a visual indication of the operation status of the AP.
Introduction Reset Button Use the reset button to clear an AP’s configuration and set it back to its factory defaults. To restore the factory default, use a small pin to press and hold the reset button for 10 seconds while the AP has power applied. Antenna The Fusion 70 Access Point comes standard with three internal antennas. However, the AP also includes three external antenna connectors that allow you to connect external antennas (optional) to them to increase the range of each radio.
Specifications Specifications Table 6 General Specifications Specification Description Dimensions (L) 7.8" (19.7 cm) X (W) 7.8" (19.7cm) X (H) 1.8" (4.5cm) • • Standards support • • • IEEE 802.3ab IEEE 802.3af IEEE 802.11b IEEE 802.11g IEEE 802.11n • • • 802.11g: 54, 48, 36, 24, 18, 12, 9 and 6 Mbps 802.11b: 11, 5.5, 2 and 1 Mbps 802.11n: MCS 0 to 15 for HT20MHz, 6.5-130 Mbps MCS 0 to 15 for HT40MHz, • 802.11b/g/n: 2.4–2.484 GHz • • 802.11b: DSSS (Direct Sequence Spread Spectrum) 802.
Installation Installation Prerequisites The following are the prerequisites that you need to adhere to before attempting to install the Fusion 70 Access Point: For ease of cable connections, ensure that the access point is near a hub or computer, as well as a reliable power source. Ensure that the access point is away from any equipment that might cause radio signal interference, such as transformers, radar, heavyduty motors, microwave ovens, refrigerators, or other.
Installation 4. Connect the power cable to the power connection located on the bottom of the AP. The Power LED turns green as soon as power is applied. 5. Mount the AP using the mounting slots located at the bottom of the AP. Note: You can also use the slots on the side of the AP if you cannot mount the AP using the slots on the bottom of the AP. Desktop Mounting Do the following to place the AP on a table or desktop: 1. Insert the tabs on the table stand into the slots on the side of the AP.
Finding Product Documentation Finding Product Documentation The documentation CD with this unit includes the following documents: CompleteMobility Express Web User Interface Reference Manual CompleteMobility Express CLI Reference Guide Fusion 70 Installation Guide (also printed) Fusion 300 Controller Hardware Reference Guide Fusion 300 and CompleteMobility Express Release Note To view PDF files, use Adobe Acrobat® Reader® 5.0, or newer.
Regulatory Information Regulatory Information The U4EA Wireless 11b/g/n PoE Access Point (Fusion 70) must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the product. This product contains encryption. It is unlawful to export out of the U.S. without obtaining a U.S. Export License. This product does not contain any user serviceable components.
This device has been designed to operate with an antenna having a maximum gain of 3 dBi. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms Only the antennas listed below are allowed to be used with the radio. Ant Antenna Type Model Name Product description 2.4 GHz Gain (dBi) Tx/Rx mode Remark 1 Monopole Ant. TWX145XRSXX-361 2dBi Dual-Band Omni Antenna 2 2T3R Main Ant. for test 2 PCB Ant.
INDUSTRY CANADA — RF COMPLIANCE INDUSTRY CANADA — RF COMPLIANCE This device complies with RSS 210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device.
EU Declaration of Conformity EU Declaration of Conformity We, the undersigned, on behalf of U4EA Technologies, Inc., hereby declare that the products listed below conform to the relevant provisions of the legislation, as well as pertinent clauses of the standards and other normative documents mentioned herein. Type of product: Access Point Product name/model: Fusion 70 Intended use: Provide effective provisioning of converged VOIP and data services. For public and private use.
EU Declaration of Conformity Ελληνική [Greek] ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ U4EA Corporation ΔΗΛΩΝΕΙ ΟΤΙ RLAN device ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ. Francais [French] Par la presente U4EA declare que l'appareil RLAN device est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE.
454 Kato Terrace Fremont, CA 94539 www.u4eatech.
