User Manual
Table Of Contents
- Contents
- Safety precautions
- Installing the monitor
- To attach the base:
- 1 Carefully set the monitor on its side with the bottom of the monitor facing you.
- 2 Hold the base so that the narrow end is pointed toward the back of the monitor.
- 3 Align the four hooks on the bottom of the base with the corresponding slots on the bottom of th...
- 4 Slide the base toward the front of the monitor so that all hooks are securely in place. A retai...
- 5 Carefully set the monitor upright and place the monitor on a sturdy, level surface.
- 1 Carefully set the monitor on its side with the bottom of the monitor facing you.
- To connect the power and video cables:
- 1 Position the monitor and the computer so that you can easily get at the back panel of each. Mak...
- 2 Connect one end of the video cable that came with the monitor to the matching video connector o...
- 3 Connect the other end of the video cable to the matching blue video connector on the back of yo...
- 4 Tighten the screws on the video cable connectors to keep them from coming loose. Tightening the...
- 5 Connect the power cord that came with the monitor to the ACpower connector at the back of the ...
- 6 Plug the other end of the power cord into a properly grounded electrical outlet.
- 1 Position the monitor and the computer so that you can easily get at the back panel of each. Mak...
- Removing the base
- To attach the base:
- Starting the monitor
- Adjusting display settings
- A Flywheel control
- B Combination power button and power LED
- OSD options
- To adjust the display settings:
- 1 Press the flywheel control. The main menu opens. The current display settings appear across the...
- 2 Rotate the flywheel control to highlight an option. The name of the highlighted option appears ...
- 3 Press the flywheel control to select the highlighted option, then rotate the flywheel control t...
- 4 Rotate the flywheel control until Exit is highlighted, then press the flywheel control to exit ...
- 1 Press the flywheel control. The main menu opens. The current display settings appear across the...
- To adjust the display settings:
- Video modes
- Power management
- Maintenance
- Troubleshooting
- Important
- No picture
- Make sure that the computer is on.
- Move the mouse or press any key on the keyboard to bring the monitor out of sleep mode.
- Check the video connector and the end of the video cable for any pins that might be bent or pushe...
- Make sure that the video cable is not damaged.
- Restart the computer with the monitor turned on.
- Picture is scrambled
- To reset your monitor to its default settings:
- 1 Start the system.
- 2 Press Ctrl.
- 3 Select Safe mode and wait for the system to finish starting up. Windows98™ starts in a “safe m...
- 4 Click Start, then select Settings, then Control Panel. The Control Panel window opens.
- 5 Double-click the Display icon. The Display Properties window opens.
- 6 Click the Settings tab.
- 7 Click Advanced. The Advanced Display Properties window opens.
- 8 Click the Monitor tab.
- 9 Click Change. The Select Device window opens.
- 10 Select Plug and Play monitor (VESA DDC) by following the on-screen instructions.
- 11 Restart Windows.
- 1 Start the system.
- To reset your monitor to its default settings:
- Display colors are wrong
- Picture is fuzzy
- Picture bounces, jitters, or has waves
- Picture has shadows or “ghosts”
- Color is not uniform
- Image is not sized or centered properly
- Image cannot be adjusted full screen
- No picture
- Important
- ECO document
Installing the monitor
3
Installing the monitor
Installing the monitor consists of two procedures: attaching the base and
connecting the monitor cables.
If you are setting up your system for the first time, refer to the setup poster
for more information about connecting additional peripherals.
To attach the base:
1
Carefully set the monitor on its side with the bottom of the monitor
facing you.
2
Hold the base so that the narrow end is pointed toward the back of the
monitor.
3
Align the four hooks on the bottom of the base with the corresponding
slots on the bottom of the monitor.
4
Slide the base toward the front of the monitor so that all hooks are
securely in place. A retaining latch built into the base clicks into place
when the base is correctly attached.
5
Carefully set the monitor upright and place the monitor on a sturdy, level
surface.