User Manual
Table Of Contents
- Contents
- Safety precautions
- Installing the monitor
- To attach the base:
- 1 Carefully set the monitor on its side with the bottom of the monitor facing you.
- 2 Hold the base so that the narrow end is pointed toward the back of the monitor.
- 3 Align the four hooks on the bottom of the base with the corresponding slots on the bottom of th...
- 4 Slide the base toward the front of the monitor so that all hooks are securely in place. A retai...
- 5 Carefully set the monitor upright and place the monitor on a sturdy, level surface.
- 1 Carefully set the monitor on its side with the bottom of the monitor facing you.
- To connect the power and video cables:
- 1 Position the monitor and the computer so that you can easily get at the back panel of each. Mak...
- 2 Connect one end of the video cable that came with the monitor to the matching video connector o...
- 3 Connect the other end of the video cable to the matching blue video connector on the back of yo...
- 4 Tighten the screws on the video cable connectors to keep them from coming loose. Tightening the...
- 5 Connect the power cord that came with the monitor to the ACpower connector at the back of the ...
- 6 Plug the other end of the power cord into a properly grounded electrical outlet.
- 1 Position the monitor and the computer so that you can easily get at the back panel of each. Mak...
- Removing the base
- To attach the base:
- Starting the monitor
- Adjusting display settings
- A Flywheel control
- B Combination power button and power LED
- OSD options
- To adjust the display settings:
- 1 Press the flywheel control. The main menu opens. The current display settings appear across the...
- 2 Rotate the flywheel control to highlight an option. The name of the highlighted option appears ...
- 3 Press the flywheel control to select the highlighted option, then rotate the flywheel control t...
- 4 Rotate the flywheel control until Exit is highlighted, then press the flywheel control to exit ...
- 1 Press the flywheel control. The main menu opens. The current display settings appear across the...
- To adjust the display settings:
- Video modes
- Power management
- Maintenance
- Troubleshooting
- Important
- No picture
- Make sure that the computer is on.
- Move the mouse or press any key on the keyboard to bring the monitor out of sleep mode.
- Check the video connector and the end of the video cable for any pins that might be bent or pushe...
- Make sure that the video cable is not damaged.
- Restart the computer with the monitor turned on.
- Picture is scrambled
- To reset your monitor to its default settings:
- 1 Start the system.
- 2 Press Ctrl.
- 3 Select Safe mode and wait for the system to finish starting up. Windows98™ starts in a “safe m...
- 4 Click Start, then select Settings, then Control Panel. The Control Panel window opens.
- 5 Double-click the Display icon. The Display Properties window opens.
- 6 Click the Settings tab.
- 7 Click Advanced. The Advanced Display Properties window opens.
- 8 Click the Monitor tab.
- 9 Click Change. The Select Device window opens.
- 10 Select Plug and Play monitor (VESA DDC) by following the on-screen instructions.
- 11 Restart Windows.
- 1 Start the system.
- To reset your monitor to its default settings:
- Display colors are wrong
- Picture is fuzzy
- Picture bounces, jitters, or has waves
- Picture has shadows or “ghosts”
- Color is not uniform
- Image is not sized or centered properly
- Image cannot be adjusted full screen
- No picture
- Important
- ECO document
24
Safety, Regulatory, and Legal Information
Notices
Copyright © 2000 Gateway, Inc.
All Rights Reserved
4545 Town Centre Court
San Diego, CA 92121 USA
All Rights Reserved
This publication is protected by copyright and all rights are reserved. No part of it may be reproduced or
transmitted by any means or in any form, without prior consent in writing from Gateway.
The information in this manual has been carefully checked and is believed to be accurate. However, changes are
made periodically. These changes are incorporated in newer publication editions. Gateway may improve and/or
change products described in this publication at any time. Due to continuing system improvements, Gateway is
not responsible for inaccurate information which may appear in this manual. For the latest product updates,
consult the Gateway Web site at www.gateway.com. In no event will Gateway be liable for direct, indirect, special,
exemplary, incidental, or consequential damages resulting from any defect or omission in this manual, even if
advised of the possibility of such damages.
In the interest of continued product development, Gateway reserves the right to make improvements in this
manual and the products it describes at any time, without notices or obligation.
Trademark Acknowledgments
AnyKey, black-and-white spot design, CrystalScan, Destination, EZ Pad, EZ Point, Field Mouse, Solo, TelePath,
Vivitron, stylized “G” design, and “Yo u ’ve got a friend in the business” slogan are registered trademarks and
GATEWAY, Gateway Profile, Gateway Solo, Gateway Astro, green stylized GATEWAY, green stylized Gateway
logo, and the black-and-white spotted box logo are trademarks of Gateway, Inc. Intel, Intel Inside logo, and
Pentium are registered trademarks and MMX is a trademark of Intel Corporation. Microsoft, MS, MS-DOS, and
Windows are trademarks or registered trademarks of Microsoft Corporation. All other product names mentioned
herein are used for identification purposes only, and may be the trademarks or registered trademarks of their
respective companies.