User Manual
Table Of Contents
- Contents
- Safety precautions
- Installing the monitor
- To attach the base:
- 1 Carefully set the monitor on its side with the bottom of the monitor facing you.
- 2 Hold the base so that the narrow end is pointed toward the back of the monitor.
- 3 Align the four hooks on the bottom of the base with the corresponding slots on the bottom of th...
- 4 Slide the base toward the front of the monitor so that all hooks are securely in place. A retai...
- 5 Carefully set the monitor upright and place the monitor on a sturdy, level surface.
- 1 Carefully set the monitor on its side with the bottom of the monitor facing you.
- To connect the power and video cables:
- 1 Position the monitor and the computer so that you can easily get at the back panel of each. Mak...
- 2 Connect one end of the video cable that came with the monitor to the matching video connector o...
- 3 Connect the other end of the video cable to the matching blue video connector on the back of yo...
- 4 Tighten the screws on the video cable connectors to keep them from coming loose. Tightening the...
- 5 Connect the power cord that came with the monitor to the ACpower connector at the back of the ...
- 6 Plug the other end of the power cord into a properly grounded electrical outlet.
- 1 Position the monitor and the computer so that you can easily get at the back panel of each. Mak...
- Removing the base
- To attach the base:
- Starting the monitor
- Adjusting display settings
- A Flywheel control
- B Combination power button and power LED
- OSD options
- To adjust the display settings:
- 1 Press the flywheel control. The main menu opens. The current display settings appear across the...
- 2 Rotate the flywheel control to highlight an option. The name of the highlighted option appears ...
- 3 Press the flywheel control to select the highlighted option, then rotate the flywheel control t...
- 4 Rotate the flywheel control until Exit is highlighted, then press the flywheel control to exit ...
- 1 Press the flywheel control. The main menu opens. The current display settings appear across the...
- To adjust the display settings:
- Video modes
- Power management
- Maintenance
- Troubleshooting
- Important
- No picture
- Make sure that the computer is on.
- Move the mouse or press any key on the keyboard to bring the monitor out of sleep mode.
- Check the video connector and the end of the video cable for any pins that might be bent or pushe...
- Make sure that the video cable is not damaged.
- Restart the computer with the monitor turned on.
- Picture is scrambled
- To reset your monitor to its default settings:
- 1 Start the system.
- 2 Press Ctrl.
- 3 Select Safe mode and wait for the system to finish starting up. Windows98™ starts in a “safe m...
- 4 Click Start, then select Settings, then Control Panel. The Control Panel window opens.
- 5 Double-click the Display icon. The Display Properties window opens.
- 6 Click the Settings tab.
- 7 Click Advanced. The Advanced Display Properties window opens.
- 8 Click the Monitor tab.
- 9 Click Change. The Select Device window opens.
- 10 Select Plug and Play monitor (VESA DDC) by following the on-screen instructions.
- 11 Restart Windows.
- 1 Start the system.
- To reset your monitor to its default settings:
- Display colors are wrong
- Picture is fuzzy
- Picture bounces, jitters, or has waves
- Picture has shadows or “ghosts”
- Color is not uniform
- Image is not sized or centered properly
- Image cannot be adjusted full screen
- No picture
- Important
- ECO document
22
Safety, Regulatory, and Legal Information
European users
European directives
This Information Technology Equipment has been tested and found to comply with the
following European directives:
■
EMC Directive 89/336/EEC amending directive 92/31/EEC & 93/68/EEC as per
- EN 50081-1:1992 according to
EN 55022:1994 Class B
EN 61000-3-2:1995 or EN 60555-2:1987
EN 61000-3-3:1995 or EN 60555-3:1987
- EN 50082-1:1992 according to
EN 61000-4-2:1995 or IEC 801-2:1984
EN 61000-4-3:1996 or IEC 801-3:1984
EN 61000-4-4:1995 or IEC 801-4:1988
■
Low Voltage Directive (Safety) 73/23/EEC as per EN 60950:1992(A1/A2/A3/A4/A11)
Japanese users
VCCI statement
This equipment is in the Class B category (Information Technology Equipment to be used in a
residential area or an adjacent area thereto) and conforms to the standards set by the Voluntary
Control Council for Interference by Information Technology Equipment aimed at preventing
radio interference in such residential areas. When used near a radio or TV receiver, it may
become the cause of radio interference. Read instructions for correct handling.
Australia and New Zealand users
EMI statement
This device has been tested and found to comply with the limits for a Class B digital device,
pursuant to the Australian/New Zealand standard AS/NZS 3548 set out by the Australian
Communications Authority and Radio Spectrum Management Agency.