SDS

7. Handling and storage
Obtain special instructions before use. Do not handle until all safety precautions have been read
and understood. Pressurized container: Do not pierce or burn, even after use. Do not use if spray
button is missing or defective. Do not spray on a naked flame or any other incandescent material.
Do not smoke while using or until sprayed surface is thoroughly dry. Do not cut, weld, solder, drill,
grind, or expose containers to heat, flame, sparks, or other sources of ignition. All equipment used
when handling the product must be grounded. Close valve after each use and when empty. Protect
cylinders from physical damage; do not drag, roll, slide, or drop. When moving cylinders, even for
short distances, use a cart (trolley, hand truck, etc.) designed to transport cylinders. Suck back of
water into the container must be prevented. Do not allow backfeed into the container. Purge air
from system before introducing gas. Use only properly specified equipment which is suitable for
this product, its supply pressure and temperature. Contact your gas supplier if in doubt. Do not
re-use empty containers. Do not breathe mist or vapor. Avoid contact with eyes, skin, and clothing.
Avoid prolonged or repeated contact with skin. Avoid prolonged exposure. Do not taste or swallow.
When using, do not eat, drink or smoke. Pregnant or breastfeeding women must not handle this
product. Should be handled in closed systems, if possible. Use only in well-ventilated areas. Wear
appropriate personal protective equipment. Wash hands thoroughly after handling. Avoid release
to the environment. Wash contaminated clothing before reuse. Observe good industrial hygiene
practices.
Precautions for safe handling
Level 3 Aerosol.
Store locked up. Pressurized container. Protect from sunlight and do not expose to temperatures
exceeding 50°C/122 °F. Do not puncture, incinerate or crush. Do not handle or store near an open
flame, heat or other sources of ignition. This material can accumulate static charge which may
cause spark and become an ignition source. Cylinders should be stored upright, with valve
protection cap in place, and firmly secured to prevent falling or being knocked over. Stored
containers should be periodically checked for general condition and leakage. Store in a
well-ventilated place. Keep out of the reach of children. Store away from incompatible materials
(see Section 10 of the SDS).
Conditions for safe storage,
including any incompatibilities
8. Exposure controls/personal protection
Occupational exposure limits
US. OSHA Table Z-1 Limits for Air Contaminants (29 CFR 1910.1000)
ValueComponents
Form
Type
PEL 435 mg/m3BENZENE, DIMETHYL
(CAS 1330-20-7)
100 ppm
PEL 245 mg/m3BENZENE,1-METHYLETHY
L-
(CAS 98-82-8)
50 ppm
PEL 9000 mg/m3Carbon Dioxide (CAS
124-38-9)
5000 ppm
PEL 5 mg/m3 Mist.Distillates (petroleum),
Hydrotreated Heavy
Naphthenic (CAS
64742-52-5)
2000 mg/m3
500 ppm
PEL 435 mg/m3ETHYLBENZENE (CAS
100-41-4)
100 ppm
PEL 1800 mg/m3HEXANE (CAS 110-54-3)
500 ppm
PEL 400 mg/m3Naphtha (petroleum),
Hydrotreated Heavy (CAS
64742-48-9)
100 ppm
PEL 50 mg/m3NAPHTHALENE (CAS
91-20-3)
10 ppm
PEL 2900 mg/m3Stoddard Solvent (CAS
8052-41-3)
500 ppm
4 / 16
Material name: Liquid Wrench Silicone Spray
M914, M914/6, M914/4 Version #: 04 Revision date: 12-16-2015 Issue date: 06-01-2015
SDS US