Technical Specifications

APPLYING THE PRODUCT
Preparation: Surfaces must be clean, dry and structurally sound.
1. Cut nozzle at a 45° angle to desired size.
2. Puncture inner seal with nail or wire.
Cabinets and counter tops: Apply a 1/4" bead to contact areas on the back of cabinets
or counter tops. Press firmly into place. Mechanical fasteners must also be used for
installing wall cabinets.
Materials to furring strips or studs: Apply zigzag 1/4" bead to each strip or stud to
be covered by panel. Position panel so edges meet at stud center; only severely warped
materials require finishing nails at top and bottom.
CLEAN UP
Use mineral spirits or an adhesive remover.
DISPOSAL
Contains organic solvents which may cause adverse effects to the environment if
disposed of improperly. Place empty containers in normal refuse for disposal. Contact
your sanitation department or household hazardous waste coordinator for information
concerning possible re-use or disposal of unused solvent-containing adhesives
and/or sealants. EAD-C9
LIMITED WARRANTY
PPG warrants satisfaction with this product when handled and applied according to label
instructions. If product is not as warranted, PPG will, at your option, furnish replacement
product or refund the purchase price. Please call 1-800-634-0015 for details. This limited
warranty excludes labor or the cost of labor and is given as the exclusive warranty and
remedy. No warranty of merchantability, fitness for purpose or other warranty,
express or implied, is made. PPG shall not be liable for any special, incidental
or consequential damages. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above exclusions/limitations may not apply.
This limited warranty gives specific legal rights; you may have other rights that vary
by state.
LN-901/LNP-901
TECHNICAL INFORMATION
Base: Synthetic rubber & resin
Type: Solvent
Color: Tan
Appearance: Smooth
Application Temperature: 40–100° F
(5 – 38° C)
Service Temperature: -20 – 140° F
(-29 – 60° C)
Adhesion: Excellent
Consistency: Short buttery
Bridging Ability: Excellent
Extrudability: Easy
Shear Strength: 24 hours – 225 psi
48 hours – 300 psi
7 days – >425 psi
Durability: Excellent; 20 year life
Flexibility: Excellent
Water Resistance: Excellent
Exterior Weathering: Very good;
adhesive not recommended for
direct exposure to sunlight
Staining: May stain marble
Odor: Mild solvent
Working Time: 10 minutes
Minimum Cure Time: 24 hours
Weight Per Gallon: 9.4 pounds (1.12 kg/l)
Viscosity: 230,000 CPS
Volatiles: 35%
Solids: 65%
Flammability: Extremely flammable;
nonflammable when dry
Flash Point: 1°F (-17°C)
Coverage: 30 lineal ft. using 1/4" bead for
10 fl.oz.; 85 lineal ft. using 1/4"
bead for 28 fl.oz.
Shelf Life: One year from date of purchase
Specifications: Exceeds ASTM C-557
VOC: < 40% by wt. (384 g/L)
PPG Architectural Coatings
400 Bertha Lamme Drive
Cranberry Township, PA 16066
www.liquidnails.com
1-800-634-0015
LN-901/LNP-901 3/15
Liquid Nails is a registered trademark of the PPG Group of Companies.
© PPG Industries, Inc. 2015. All Rights Reserved.
DANGER! EXTREMELY FLAMMABLE. CAUSES EYE AND SKIN BURNS. HARMFUL OR FATAL
IF SWALLOWED. HARMFUL IF INHALED. MAY CAUSE CENTRAL NERVOUS SYSTEM EFFECTS,
INCLUDING DIZZINESS, HEADACHE OR NAUSEA. CAUSES RESPIRATORY TRACT IRRITATION.
USE ONLY WITH ADEQUATE VENTILATION. KEEP OUT OF THE REACH OF CHILDREN. Reports have
associated repeated and prolonged occupational overexposure to solvents with permanent brain and nervous
system damage. Intentional misuse by deliberately concentrating and inhaling the contents may be harmful or fatal.
Contains Crystalline Silica. If sanding, wear a dust mask to avoid breathing of sanding dust. Keep away from heat,
sparks and flame. Do not smoke. Vapors may ignite explosively. Vapors may spread long distances. Extinguish
all flames, burners, stoves, heaters and pilot lights and disconnect all electrical motors and appliances before use
and until all vapors are gone. Do not breathe vapors. Prevent build-up of vapors by opening all windows and doors
to achieve cross-ventilation. Avoid contact with eyes and skin. Close container after use. FIRST AID: For skin
contact, wash thoroughly with soap and water. If any product remains, gently rub with petroleum jelly, vegetable
or mineral/baby oil, then wash again with soap and water. Repeat as needed. Remove contaminated clothing. For
eye contact, flush immediately with plenty of water for at least 15 minutes. Get medical attention. If swallowed,
get medical attention immediately. If inhalation causes physical discomfort, remove to fresh air. If discomfort
persists or any breathing difficulty occurs, get medical attention. For emergency information, customer service,
MSDS or additional safety and chronic hazard information, call 1-800-634-0015. KEEP FROM FREEZING.
HEAVY DUTY
Construction Adhesive