Use and Care Manual

ManualsBrandsLippert ManualsAutomotive360° Siphon RV Holding Tank Vent Cap - Black

360 Siphon®

Aftermarket Manual

lci1.com 574-537-8900 CCD-0001583 Rev. 07.10.18

360 Siphon

Aftermarket

Manual

Table Of Contents

Introduction � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 2

Parts List� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 2

Preparation � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 3

Resources Required � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 3

Installation Options

� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 3

Modied Installation

� � � � � � � � � � � � � � � � � � � � � � � � � � � � � 3

Cap 1

� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 4

Cap 2

� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 5

Cap 3

� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 5

Cap 4

� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 6

Cap 5

� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 6

Complete Installation� � � � � � � � � � � � � � � � � � � � � � � � � � � � 8

360 Siphon

Generation 2

Summary of content (8 pages)

PAGE 1
360 Siphon® Aftermarket Manual 360 Siphon® Aftermarket Manual 360 Siphon® Generation 2 Table Of Contents Introduction �� 2 Parts List �� 2 Preparation �� 3 Resources Required �� 3 Installation Options ��
PAGE 2
360 Siphon® Aftermarket Manual Introduction Parts List The 360 Siphon® RV holding tank vent cap removes odors from the source — the holding tanks — and exhausts them out through the roof vent before they have a chance to invade the RV living space. By design, the patented 360 Siphon® can only create an updraft, expelling odors and fostering an oxygen-rich environment to speed up waste breakdown.
PAGE 3
60 Siphon® Aftermarket Manual 3. Assess the stack height and diameter. Preparation A. Things to consider before proceeding: Note: Blue lines within images refer to using adhesive/sealant on the designated area, while red lines refer to using a saw.
PAGE 4
360 Siphon® Aftermarket Manual 4. Dry fit all parts prior to adding any adhesive/sealant. Cap 1 (Fig.5, Fig.6 and Fig.7) 1. Remove the lid by removing the single screw on the top. 5. Apply a small amount of adhesive/sealant around the perimeter of the funnel that fits into the lid and insert (Fig.2). 2. Use a saw to cut off the 8 legs and lid support. lid Fig.2 base 6. If applicable, apply a small amount of adhesive/sealant around the top of the collar (Fig.3) and attach to the lid. Fig.
PAGE 5
360 Siphon® Aftermarket Manual Cap 2 (Fig.8, Fig.9 and Fig.10) 1. Remove the lid by removing the single screw on the top. Cap 3 (Fig.11 and Fig.12) 1. Use a saw to cut the top section off 1 1/2” above the roof. 2. Use a saw to cut off the 4 legs and screw support as close to the base as possible. lid top section leg base 1 1/2” Fig.8 Fig.11 Fig.9 Fig.12 Fig.10 lci1.com 574-537-8900 5 CCD-0001583 Rev. 07.10.
PAGE 6
360 Siphon® Aftermarket Manual Cap 4 (Fig.13 and Fig.14) 1. Use a saw to cut off the 3 legs that secure the lid, cut low without touching the roof seal. Cap 5 (Fig.15 and Fig.16) 1. Use a saw to make a cut 1/2” from the top of the base. lid leg Fig.13 1/2” Fig.15 Fig.14 Fig.16 lci1.com 574-537-8900 6 CCD-0001583 Rev. 07.10.
PAGE 7
360 Siphon® Aftermarket Manual When completed, the modified installations using the 360 Siphon RV holding tank vent cap with the existing bases will look similar to the pictures depicted on this page. Note: Roof fasteners and roof sealant not shown. Cap 3 Cap 1 Cap 4 Cap 2 Cap 5 lci1.com 574-537-8900 7 CCD-0001583 Rev. 07.10.
PAGE 8
360 Siphon® Aftermarket Manual Complete Installation 1. Remove old cap by gently removing the seal around the base, making sure not to damage the roof top membrane. 2. Unscrew the base from the roof. 3. Clean off the roof, fill the screw holes and check the seal around the stack. 4. Dry fit the base, funnel and lid for proper fit (Fig.17). Note: Review Modified Installation section step 3 for any concerns on the stack height and diameter. Fig.18 5.