S�����® M����� A����� - C���� S���� OWNER'S MANUAL Rev: 07.30.
TABLE OF CONTENTS System Safety Information Operation Extending the Awning Adjusting Pitch Fabric Care Solera Manual Gearbox Awning Assembly Webpage Solera Manual Gearbox Awning Components Webpage Variant Code Information Awning Fabric and Roll Bar Replacement 2 2 3 3 5 5 6 7 7 9 System Safety Information The “WARNING” symbol above is a sign that a service or maintenance procedure has a safety risk involved and may cause death or serious injury if not performed safely and within the paramet
Operation Extending the Awning 1. Locate the locking latch (Fig. 1) (if equipped) on the drive side awning arm. Unlock the latch (Fig. 2). NOTE: This latch is optional and may be installed on one or both support arms. If not installed, skip to step 2. 2. Locate the manual crank handle for the awning. 3. Insert the hook end of the crank handle into the eye bolt on the drive head (Fig. 3A). 4. Turn the crank in a counter-clockwise direction and fully extend the awning (Fig. 4).
Retracting the Awning 1. Insert the hook end of the crank handle into the eye bolt on the drive head (Fig. 6). 2. Turn the crank handle in a clockwise direction until the awning is fully retracted (Figs. 7 and 8). NOTE: Keeping handle even with the roller tube makes it easier to turn. 3. Locate the locking latch (Fig. 9) (if equipped) on the drive side awning arm. Lock the latch to secure the awning in place (Fig. 10). NOTE: This latch is optional and may not be installed.
Adjusting Pitch NOTE: Without manually setting pitch to the awning, the awning will pitch itself to purge excessive water pooling in one location and may dump a significant amount of water to either end of the awning without notice. 1. Pitch can be set manually by adjusting the articulating arm to tip one side of the awning to allow water runoff. 2. Extend awning to desired location. 3. Choose the side of the awning for optimum or convenient water runoff.
SOLERA® MANUAL AWNING - CRANK STYLE ASSEMBLY WEBPAGE AWNINGS Idler Side Head End Cap Manual Gearbox Head Manual Crank Handle Grommet Grommet Diaphragm #8 Wax Screws Box Gear with Eyelet Awning Fabric Manual Gearbox Head X-Ray View Coupler Support Arm Assembly Pin Gas Strut Box Gear with Eyelet Screw Nylock Nut Roll Bar Rev: 07.30.
SOLERA® MANUAL AWNING - CRANK STYLE COMPONENTS WEBPAGE AWNINGS Variant Code Information The variant code on Lippert products can assist LCI customers in obtaining additional information about the product and its components. For replacement part information, locate the variant code as outlined below and call LCI customer service at 574-537-8900. Roll bar Variant Code B A C D E Callout A B C D E F G Rev: 07.30.
H I J K L M O N R Q P Callout White Part # Black Part # Description H 299419 Screw - # 8 - 15 X ½ PNH ZN SQ A ST I 266156 #6 X ½ ZN Screw (fastener for head covers, 6 per cover) J K L 299630 118043 266148 M 266155 N O P 300030 266130 275071 #8 End Cap Wax Screw (head to roll bar) Nut 5⁄16-18 Nylock ZN ST (head to arm) Screw 5⁄16-18 X 2-1/4 (head to arm) Screw #8-32 x ½ PH PNH MACHG ZN FTHD (back cover to mount) Manual Crank Handle End Cap Rubber Grommet Q 299993 Grommet Diaphrag
S T U S V Callout S T U V White Part # Black Part # 295742 395743 260294 266169 281152 2881154 280343 260282 286576 282484 Description Support Arm Assembly (Short, 61") Support Arm Assembly (Pitched, 66 1⁄8") Support Arm Assembly (Flat, 69") Gas Strut; 26"; 124 LBS (for Short and Flat Arm assemblies) Gas Strut; 124 - 144 LBS (for Pitched Arm assemblies) Screw - #14 - 10 x 1 ½ (arms to coach) Star Washer (for Gas Strut) Awning Fabric and Roll Bar Replacement To order replacement awning fabric and rol
All information contained within may be distributed as a full document only, unless otherwise permitted by explicit consent of Lippert Components Inc. to distribute individual parts. All information contained within is subject to change without notice. New editions will be posted on www.lci1. com and can be downloaded for free. Information contained within is considered factual until made obsolete by a *NEW* revision. Please recycle all obsolete materials.
