User Manual

ManualsBrandsLionda Technology ManualsElectronicsFRS/GMRS

Operation

3. Press the button to confirm your selection and return to the NOR-

MAL mode.

4. To confirm and shift to the next option, press the button.

NOTE: To communicate with other FRS units, both units must be switched toGMRS/

the same channel and CTCSS sub-channel.

VOX Selection

1. Press the button thrice, the VX icon will flash on the LCD

Screen.

2. Press the UP button to turn the VOX feature ON, or press the

DOWN button to turn the VOX feature OFF.

3. In the VOX mode, the VX icon will be displayed.

4. To confirm your selection and return to the NORMAL mode, press

the button.

5. To confirm and shift to the next option, press the button.

Changing the CTCSS SUB-CHANNELS

The FRS has 38 available CTCSS sub-channels. To change

channels:

GMRS/

1. Press the button twice, the CTCSS sub-channel 0 will flash on the

LCD Screen.

2. While the CTCSS sub-channel is flashing:

The sub-channel changes from 0 to 38, or from 38 to 0.

Press the UP button to move to a higher sub-channel.

Press the DOWN button to move to a lower sub-channel.

The FRS is capable of voice activated (VOX) transmission. In VOX

mode, the radio will transmit a signal only when it is activated by your

voice or other sound around you. VOX operation is not recommended if

GMRS/

you plan to use your radio in a noisy or windy environment.

NOTE: To save power, the unit will not turn ON the LCD Screen light when in

the VOX mode.

Operation

NOTE: This FRS unit allows you to communicate with standard FRS

models by using channels 1 through 14.

GMRS/

NOTE:

and environment.

This GMRS/FRS unit has a fixed power output (0.135W) from channel 1 thru

channel 22. The maximum transmission range will vary depending on terrain

CHANNEL SCAN

CHANNEL SCAN performs searches for active signals in an endless

loop from 1 to 22.

2. When an active signal (one of 22 channels) is detected, CHANNEL SCAN

pauses keeping the active signal broadcasted.

3. Press the button to communicate through the active signal channel

and CHANNEL SCAN is deactivated.

5. Press the button to deactivate CHANNEL SCAN mode.

4. When an active signal (one of 22 channels) is detected, but another

channel is desired, press the UP or DOWN button to bypass

the current channel and continue to search for another active channel.

CHANNEL TABLE

Specifications

POWER

(Watts)

POWER

(Watts)

FREQUENCY

(MHz)

467.6625

467.6875

467.7125

CHANNEL

NUMBER

CHANNEL

NUMBER

FREQUENCY

(MHz)

467.5625

467.5875

467.6125

467.6375

462.5625

462.5875

462.6125

462.6375

462.6625

462.6875

462.7125

462.5750

462.6250

462.6750

462.5500

462.6000

462.6500

462.7000

462.7250

22 Channels

38 for each Channel

FRS/GMRS 0.135W

Channels

ailable

CTCSS Sub-channel

Output Power (TX)

Battery Charge Level/Low Battery Indication

The BATTERY CHARGE LEVEL is indicated by the number of squares

present inside the BATTERY icon on the LCD Screen.

When the BATTERY CHARGE LEVEL is low, the BATTERY icon will

flash to indicate that the batteries need to be replaced.

Sending Call Tones

You can use Call Tones to alert the other user to identify yourself. You can

also use Call Tones to signal the beginning or the end of a transmission.

1. Press and release the button.

2. Your Call Tones will transmit to nearby receivers set to the same

channel.

To use this FRS with an AC/DC ADAPTER (not included) andGMRS/

rechargeable BATTERY PACK (not included) do the following:

1. Plug the 7.5 V DC / 150 mA ADAPTER (not included) into the EAR/MIC/

CHARGER JACK on top of the GMRS/FRS and turn it ON by pressing the

POWER button.

2. The battery icon will flash while the indicator bar is scrolling.

To Charge the FRSGMRS/

NOTE: The GMRS/FRS cannot transmit calls while the batteries are being charged.

It takes approximately 5 to 6 hours to fully charge the batteries if they are at their

lowest level.

1. Press and release the button to activate CHANNEL SCAN.

The channel number on the LCD Screen changes rapidly until an

active signal is detected.

SCAN

CALL

0.135

GMRS/

FRS

GMRS/

FRS

GMRS/

FRS

GMRS/

FRS

GMRS/

FRS

GMRS/

FRS

GMRS/

FRS

GMRS