® A Division of Cisco Systems, Inc. 2.4 GHz Wireless-G 54Mbps VPN Router WIRELESS Model No. WRV54G Linksys is a registered trademark or trademark of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries.
Dual-Band Wireless Access Point Table of Contents Chapter 1: Introduction 1 Welcome What’s in this Guide? 1 2 Chapter 2: Planning your Wireless Network Network Topology Roaming Network Layout Chapter 3: Getting to Know the Access Point The Back Panel The Front Panel Chapter 4: Connecting the Access Point Hardware Installation Chapter 5: Setting Up the Access Point Setup Wizard Chapter 6: Configuring the Access Point Overview The Setup Tab The Password Tab The Status Tab The Help Tab The Filter Tab
Dual-Band Wireless Access Point Appendix G: Warranty Information Appendix H: Regulatory Information Appendix I: Contact Information 41 42 44
Dual-Band Wireless Access Point List of Figures Figure 1-1: 1 Figure 1-2: 1 Figure 1-3: 2 Figure 1-4: 2 Figure 1-5: Figure 1-6: Figure 1-7: Figure 1-8: Figure 1-9: Figure 1-10: Figure 1-11: Figure 1-12: Figure 2-1: Network Figure 2-2: 4 Figure 2-3: 4 Figure 2-4: 4 Figure 2-5: 4 Figure 2-6: 4 Figure 2-7: 4 Figure 2-8: 4 Figure 2-9: 4 Figure 2-10: 4 Figure 2-11: 4 Figure 2-12: 4 Figure 3-1: Back Panel Figure 3-2: Front Panel Figure 3-3: 7 Figure 3-4: 7 Figure 3-5: 7 Figure 3-6: 7 2 2 2 2 2 2 2 2 4 5 6 Fig
Dual-Band Wireless Access Point Figure 5-13: 12 Figure 5-14: 12 Figure 5-15: 12 Figure 6-1: Password Screen 15 Figure 6-2: Setup Tab 16 Figure 6-3: 802.11b Wireless Setings 17 Figure 6-4: Password Tab 17 Figure 6-5: Status Tab 18 Figure 6-6: Help Tab 18 Figure 6-7: Filter Tab 19 Figure 6-8: Wireless Tab 20 Figure 6-9: 21 Figure 6-10: 21 Figure 6-11: 21 Figure 6-12: 21 Figure 6-13: 21 Figure 6-14: 21 Figure 6-15: 21 Figure B-1: Warchalking Figure B-2: 802.11a WEP Key Setting Figure B-3: 802.
Wireless-G Broadband VPN Router Chapter 1: Introduction Welcome Wireless-G is the upcoming 54Mbps wireless networking standard that’s almost five times faster than the widely deployed Wireless-B (802.11b) products found in homes, businesses, and public wireless hotspots around the country—but since they share the same 2.4GHz radio band, Wireless-G devices can also interoperate with existing 11Mbps Wireless-B equipment. Since both standards are built in, you can protect your investment in existing 802.
Dual-Band Wireless Access Point Chapter 2: Planning your Wireless Network The Router’s Functions Simply put, a router is a network device that connects two networks together. In this instance, the Router connects your Local Area Network (LAN), or the group of PCs in your home or office, to the Internet. The Router processes and regulates the data that travels between these two networks. The Router’s NAT feature protects your network of PCs so users on the public, Internet side cannot “see” your PCs.
Dual-Band Wireless Access Point Chapter 6: Configuring the Router’s Basic Settings This chapter will show you how to configure the Router to function in your network and gain access to the Internet through your Internet Service Provider (ISP). Detailed description of the Router’s web-based utility can be found in “Chapter 6: The Router’s Web-based Utility.” The instructions from your ISP tell you how to set up your PC for Internet access.
Dual-Band Wireless Access Point The Setup Tab The first screen that appears displays the Setup tab. This allows you to change the Access Point's general settings. Change these settings as described here and click the Apply button to apply your changes or Cancel to cancel your changes. If you require online help, click the Help button. • Firmware. This will display the Access Point's current firmware version. Firmware can be upgraded from the Help tab. • Access Point Name.
Dual-Band Wireless Access Point 2.4GHz/802.11b Wireless Settings • SSID. The SSID is the unique name shared among all points in a wireless network. The SSID must be identical for all points in the wireless network. It is case sensitive and must not exceed 32 alphanumeric characters, which may be any keyboard character. Make sure this setting is the same for all points in your wireless network. • Channel. Select the appropriate channel from the list provided to correspond with your network settings.
Dual-Band Wireless Access Point The Status Tab The Status tab will display current information on the Access Point, its settings and performance. • Firmware Version. This displays the current version of the Access Point's firmware. Firmware should only be upgraded if you experience problems with the Access Point and can be upgraded from the Help tab. • IP Address. This IP address is the unique address to your network. • Subnet Mask.
Dual-Band Wireless Access Point The Filter Tab The Filter tab allows you to block and allow certain computers, by their MAC Address, from communicating with the Access Point. To enable filtering of computers by their MAC Addresses, click the Enable radio button. To disable this feature, click the radio button by Disable. Type the MAC Addresses for those PCs you wish to allow access to the Access Point in the MAC Address fields.
Dual-Band Wireless Access Point The Wireless Tab Before making any changes to the Wireless tab, please check your wireless settings on other systems, as these changes will alter the effectiveness of the Access Point. In most cases, these settings do not need to be changed. • Beacon Interval. This value indicates the frequency interval of the beacon. A beacon is a packet broadcast by the Access Point to keep the network synchronized.
Dual-Band Wireless Access Point • Preamble Type. (2.4GHz/802.11b only) The preamble synchronizes network traffic for more efficient communication. Small networks benefit most from Short preambles. Large networks benefit from Long preambles. All points in your wireless network must be set to the same preamble type. • Authentication Type. You may choose between Open System or Shared Key. The Authentication Type default is set to Open System, in which the sender and the recipient do NOT share a secret key.
Dual-Band Wireless Access Point Chapter 5: Configuring the PCs Overview The instructions in this chapter will help you configure each of your computers to be able to communicate with the Router. To do this, you need to configure your PC’s network settings to obtain an IP (or TCP/IP) address automatically, so your PC can function as a DHCP client. Computers use IP addresses to communicate with the Router and each other across a network, such as the Internet.
Dual-Band Wireless Access Point Chapter 4: Connecting the Wireless-G Broadband Router Overview The Router’s setup consists of more than simply plugging hardware together. You will have to configure your networked PCs to accept the IP addresses that the Router assigns them (if applicable), and you will also have to configure the Router with setting(s) provided by your Internet Service Provider (ISP).
Dual-Band Wireless Access Point Chapter 3: Getting to Know the Wireless-G Broadband VPN Router The Back Panel The Router’s ports, where a network cable is connected, are located on the back panel. Figure 3-1: Back Panel Internet The Internet port connects to your modem. LAN (1-4) The LAN (Local Area Network) ports connect to your PC and other network devices. Power The Power port is where you will connect the power adapter. Reset Button There are two ways to Reset the Router's factory defaults.
Dual-Band Wireless Access Point Chapter 7: Configuring the Router’s Web-Based Utility Overview Use the Router’s web-based utility to administer it. This chapter will describe each web page in the Utility and each page’s key functions. The utility can be accessed via your web browser through use of a computer connected to the Router. For a basic network setup, most users only have to use the following screens of the Utility: • Basic Setup. On the Basic Setup screen, enter the settings provided by your ISP.
Dual-Band Wireless Access Point • Advanced Wireless Settings. On this screen you can access the Advanced Wireless features of Authentication Type, Basic Data Rates, Control Tx Rates, Beacon Interval, DTIM Interval, RTS Threshold, and Fragmentation Threshold. Beacon Interval :The frequency interval of the beacon, which is a packet broadcast by a router to synchronize a wireless network. Security • Filter.
Dual-Band Wireless Access Point • Local Network. This provides status information about the local network. How to Access the Web-based Utility To access the web-based utility, launch Internet Explorer or Netscape Navigator, and enter the Router’s default IP address, 192.168.1.1, in the Address field. Then press Enter. A password request page, shown in Figure 6-2 will pop up. (non-Windows XP users will see a similar screen.
Dual-Band Wireless Access Point Static If you are required to use a permanent IP address to connect to the Internet, then select Static IP. • IP Address. This is the Router’s IP address, when seen from the WAN, or the Internet. Your ISP will provide you with the IP Address you need to specify here. • Subnet Mask. This is the Router’s Subnet Mask, as seen by external users on the Internet (including your ISP). Your ISP will provide you with the Subnet Mask. • Default Gateway.
Dual-Band Wireless Access Point PPPTP Point to Point Tunneling Protocol (PPTP) is a service that applies to connections in Europe only (see Figure 68). • Internet IP Address. This is the Router’s IP address, when seen from the Internet. Your ISP will provide you with the IP Address you need to specify here. • Subnet Mask. This is the Router’s Subnet Mask, as seen by external users on the Internet (including your ISP). Your ISP will provide you with the Subnet Mask. • Default Gateway.
Dual-Band Wireless Access Point 1200 to 1500 range. For most DSL users, it is recommended to use the value 1492. By default, MTU is set at 1500 when disabled. Network Setup • Gateway IP. The values for the Router’s Local IP Address and Subnet Mask are shown here. In most cases, keeping the default values will work. • Local IP Address. The default value is 192.168.1.1. • Subnet Mask. The default value is 255.255.255.0. • Network Address Server Settings (DHCP).
Dual-Band Wireless Access Point The DDNS Tab The Router offers a Dynamic Domain Name System (DDNS) feature. DDNS lets you assign a fixed host and domain name to a dynamic Internet IP address. It is useful when you are hosting your own website, FTP server, or other server behind the Router. Before you can use this feature, you need to sign up for DDNS service at one of two DDNS service providers, DynDNS.org or TZO.com. DDNS DDNS Service. If your DDNS service is provided by DynDNS.org, then select DynDNS.
Dual-Band Wireless Access Point MAC Address Clone Tab The Router’s MAC address is a 12-digit code assigned to a unique piece of hardware for identification, like a social security number. If your ISP requires MAC address registration, find your adapter’s MAC address by following the instructions in “Appendix D: Finding the MAC Address and IP Address for Your Ethernet Adapter.” MAC Clone • MAC Clone Service. To use MAC address cloning, select Enable. • MAC Address.
Dual-Band Wireless Access Point Static Routing If the Router is connected to more than one network, it may be necessary to set up a static route between them. A static route is a pre-determined pathway that network information must travel to reach a specific host or network. To create a static route, change the following settings: • Select Number. Select the number of the static route from the drop-down menu. The Router supports up to 20 static route entries. • Delete This Entry.
Dual-Band Wireless Access Point Hot Spot Hot Spot Service Provider. Select the Hot Spot Provider from the drop-down menu. Hot Spot Sevice Provider URL. Enter the Hot Spot Sevice Provider URL in the field. Hot Spot Object ID. Enter the Hot Spot Object ID in the field. Click Register to __________________________. Click Hot Spot Status to view the status. Click the Clear button to clear the information you’ve entered.
Dual-Band Wireless Access Point Wireless Security • Wireless SSID Broadcast. When wireless clients survey the local area for wireless networks to associate with, they will detect the SSID broadcast by the Router. To broadcast the Router's SSID, keep the default setting, Enabled. If you do not want to broadcast the Router's SSID, then select Disabled. • WEP. An acronym for Wired Equivalent Privacy, WEP is an encryption method used to protect your wireless data communications.
Dual-Band Wireless Access Point Wireless Network Access Wireless Network Access. If this function is enabled, only the computers on the list will be allowed access to the wireless network. To add a computer to the network, click the Permit to access button, and enter the MAC address in the fields. Click the Select MAC Address From Networked Computers button, and the screen in figure 7-15 will appear. Select the MAC Address from the list and click the Select button.
Dual-Band Wireless Access Point Advanced Wireless Settings On this screen you can access the Advanced Wireless features of Authentication Type, Basic Data Rates, Control Tx Rates, Beacon Interval, DTIM Interval, RTS Threshold, and Fragmentation Threshold. • Authentication Type. The default is set to Auto, which allows either Open System or Shared Key authentication to be used. For Open System authentication, the sender and the recipient do NOT use a WEP key for authentication.
Dual-Band Wireless Access Point The Security Tab Firewall When you click the Security tab, you will see the Firewall screen (see Figure 6-16). This screen contains Filters and Block WAN Requests. Filters block specific internal users from accessing the Internet and block anonymous Internet requests and/or multicasting. • Firewall. To add Firewall Protection, click Enabled. If you do not want Firewall Protection, click Disabled. • Filter Proxy. Use of WAN proxy servers may compromise the Router's security.
Dual-Band Wireless Access Point VPN Virtual Private Networking (VPN) is a security measure that basically creates a secure connection between two remote locations. This connection is very specific as far as its settings are concerned; this is what creates the security. The VPN screen, shown in Figure 7-18, allows you to configure your VPN settings to make your network more secure. VPN PassThrough • IPSec Passthrough.
Dual-Band Wireless Access Point connection cannot be made. Remember, this is NOT the IP Address of the local VPN Router, but the IP Address of the remote VPN Router or device with which you wish to communicate. • Encryption. Using Encryption also helps make your connection more secure. There are two different types of encryption: DES or 3DES (3DES is recommended because it is more secure).
Dual-Band Wireless Access Point Advanced VPN Tunnel Setup From the Advance VPN Tunnel Setup screen, shown in Figure 7-19, you can adjust the settings for specific VPN tunnels. Phase 1 • Phase 1 is used to create a security association (SA), often called the IKE SA. After Phase 1 is completed, Phase 2 is used to create one or more IPSec SAs, which are then used to key IPSec sessions. • Operation Mode. There are two modes: Main and Aggressive, and they exchange the same IKE payloads in different sequences.
Dual-Band Wireless Access Point Other Options • Unauthorizes IP Blocking. Click Enabled to block unauthorized IP addresses. Enter in the Rejects Number field to specify how many times IKE must fail before blocking that unauthorized IP address. Enter the length of time that you specify (in seconds) in the Block Period field. When finished making your changes on this tab, click the Save Settings button to save these changes, or click the Cancel Changes button to undo your changes.
Dual-Band Wireless Access Point • WEP Encryption. Select the level of WEP encryption you wish to use, 64-bit 10 hex digits or 128-bit 26 hex digits. Higher encryption levels offer higher levels of security, but due to the complexity of the encryption, they may decrease network performance. • Passphrase. Instead of manually entering WEP keys, you can enter a Passphrase. This Passphrase is used to generate one or more WEP keys. It is case-sensitive and should not be longer than 16 alphanumeric characters.
Dual-Band Wireless Access Point 2. Click the Edit List button. This will open the List of PCs screen, shown in Figure 7-23. From this screen, you can enter the IP address or MAC address of any PC to which this policy will apply. You can even enter ranges of PCs by IP address. Click the Apply button to save your settings, the Cancel button to undo any changes, and the Close button to return to the Filters tab. 3.
Dual-Band Wireless Access Point Applications and Gaming Port Range Forwarding The Port Forwarding screen sets up public services on your network, such as web servers, ftp servers, e-mail servers, or other specialized Internet applications. (Specialized Internet applications are any applications that use Internet access to perform functions such as videoconferencing or online gaming. Some Internet applications may not require any forwarding.
Dual-Band Wireless Access Point When finished making your changes on this tab, click the Save Settings button to save these changes, or click the Cancel Changes button to undo your changes. UPnP Forwarding The UPnP screen displays preset application settings as well as options for customization of port services for other applications. • Application. Ten preset applications are preset. You can specify up to five additional applications in the available fields.
Dual-Band Wireless Access Point with little selectivity. All pending messages and attachments are downloaded at the same time. POP3 uses the SMTP messaging protocol. • NNTP (Network News Transfer Protocol) The protocol used to connect to Usenet groups on the Internet. Usenet newsreaders support the NNTP protocol. • SNMP (Simple Network Management Protocol) A widely used network monitoring and control protocol.
Dual-Band Wireless Access Point DMZ The DMZ screen allows one local user to be exposed to the Internet for use of a special-purpose service such as Internet gaming and videoconferencing. Whereas Port Range Forwarding can only forward a maximum of 10 ranges of ports, DMZ hosting forwards all the ports for one PC at the same time. • Software DMZ. To use this feature, select Enabled. To disable DMZ , select Disabled. • DMZ Host IP Address. To expose one PC, enter the computer’s IP address.
Dual-Band Wireless Access Point Administration Management The Management screen allows you to change the Router’s access settings as well as configure the SNMP and UPnP (Universal Plug and Play) features. Router Password Local Router Access. To ensure the Router’s security, you will be asked for your password when you access the Router’s Web-based Utility. The default password is admin. • Router Password. It is recommended that you change the default password to one of your choice. • Re-enter to confirm.
Dual-Band Wireless Access Point • SNMP Trap-Destination. Enter the IP Address. UPnP UPnP allows Windows XP to automatically configure the Router for various Internet applications, such as gaming and videoconferencing. To enable UPnP, click Enabled. • Allow User to make Configuration Changes. When enabled, this feature allows you to make manual changes while still using the UPnP feature. • Allow users to disable Internet access.
Dual-Band Wireless Access Point Notification Qeue Length • Log queue Length. Enter the number of entries in the log queue in the field. • Log Time Threshold. Enter the time for the threshold in the field. Alert Log Select the alert log that you want to ______. Select Syn Flooding, IP Spoofing, Win Nuke, Ping of Death, or Unauthorized Login attempt. General Log. Select the ________.
Dual-Band Wireless Access Point Factory Default If you have exhausted all other options and wish to restore the Router to its factory default settings and lose all your settings, click Yes. When finished making your changes on this tab, click the Save Settings button to save these changes, or click the Cancel Changes button to undo your changes. Figure 7-33: Firmware Upgrade To upgrade the Router’s firmware: 1.
Dual-Band Wireless Access Point Status Router This screen displays information about your Router and its WAN (Internet) Connections. Information The information displayed is the Hardware Version, Software Version, MAC Address, Local MAC Address, and System Up Time. WAN Connections The WAN Connections displayed are the Network Access, WAN IP Address, Subnet Mask, Default Gateway, and DNS. Click the Refresh button if you want to Refresh your screen.
Dual-Band Wireless Access Point Local Network The Local Network information that is displayed is the IP Address, Subnet Mask, DHCP Server, and DHCP Client Lease Info. To view the DHCP Clients Table, click the DHCP Clients button. See Figure 7-36. The DHCP Active IP Table, Figure 7-37, displays the computer name, IP Address, MAC Address and the expiration time. Click the Close button to return to the Local Network screen.
Dual-Band Wireless Access Point Wireless The Wireless Network information that is displayed is the MAC Address, Mode, SSID, Channel, and Encryption Function. Click the Refresh button if you want to Refresh your screen. System Performance The System Peformance information that is displayed is the Wireless, Internet, and/or LAN information for the IP Address, MAC Address, Connection Status, Packets Received, Packets Sent, Bytes Received, Bytes Sent, Error Packes Received, and Dropped Packets Received.
Dual-Band Wireless Access Point Appendix A: Troubleshooting This appendix consists of two parts: “Common Problems and Solutions” and “Frequently Asked Questions.” Provided are possible solutions to problems that may occur during the installation and operation of the Router. Read the descriptions below to help you solve your problems. If you can’t find an answer here, check the Linksys website at www.linksys.com. Common Problems and Solutions 1. I need to set a static IP address on a PC.
Dual-Band Wireless Access Point 4. Enter a unique IP address that is not used by any other computer on the network connected to the Router. You can only use an IP address in the ranges 192.168.1.2 to 192.168.1.99 and 192.168.1.151 to 192.168.1.254. 5. Enter the Subnet Mask, 255.255.255.0. 6. Enter the Default Gateway, 192.168.1.1 (Router’s default IP address). 7.
Dual-Band Wireless Access Point 4. In the This connection uses the following items box, highlight Internet Protocol (TCP/IP). Click the Properties button. 5. Enter a unique IP address that is not used by any other computer on the network connected to the Router. You can only use an IP address in the ranges 192.168.1.2 to 192.168.1.99 and 192.168.1.151 to 192.168.1.254. 6. Enter the Subnet Mask, 255.255.255.0. 7. Enter the Default Gateway, 192.168.1.1 (Router’s default IP address). 8.
Dual-Band Wireless Access Point D.In the command prompt, type ping followed by your Internet or WAN IP address and press the Enter key. The Internet or WAN IP Address can be found on the Status screen of the Router’s web-based utility. For example, if your Internet or WAN IP address is 1.2.3.4, you would enter ping 1.2.3.4 and press the Enter key. • If you get a reply, the computer is connected to the Router.
Dual-Band Wireless Access Point VPNs that use IPSec with the ESP (Encapsulation Security Payload known as protocol 50) authentication will work fine. At least one IPSec session will work through the Router; however, simultaneous IPSec sessions may be possible, depending on the specifics of your VPNs. VPNs that use IPSec and AH (Authentication Header known as protocol 51) are incompatible with the Router. AH has limitations due to occasional incompatibility with the NAT standard.
Dual-Band Wireless Access Point CustomizedExternal PortTCPUDPIP AddressEnable Application Web server80 to 80X X192.168.1.100X FTP server21 to 21X192.168.1.101X SMTP (outgoing)25 to 25XX192.168.1.102X POP3 (incoming)110 to 110XX192.168.1.102X When you have completed the configuration, click the Apply button. 7. I need to set up online game hosting or use other Internet applications.
Dual-Band Wireless Access Point If you are having difficulties getting any Internet game, server, or application to function properly, consider exposing one PC to the Internet using DeMilitarized Zone (DMZ) hosting. This option is available when an application requires too many ports or when you are not sure which port services to use. Make sure you disable all the forwarding entries if you want to successfully use DMZ hosting, since forwarding has priority over DMZ hosting.
Dual-Band Wireless Access Point For Netscape 4.7 or higher: A.Start Netscape Navigator, and click Edit, Preferences, Advanced, and Proxies. B.Make sure you have Direct connection to the Internet selected on this screen. C.Close all the windows to finish. 11. To start over, I need to set the Router to factory default. Hold the Reset button for 10 seconds and then release it. This will return the password, forwarding, and other settings on the Router to the factory default settings.
Dual-Band Wireless Access Point B.Enter the password, if asked. (The default password is admin.) C.On the Setup screen, select the option Keep Alive, and set the Redial Period option at 20 (seconds). D.Click the Apply button. E.Click the Status tab, and click the Connect button. F.You may see the login status display as Connecting. Press the F5 key to refresh the screen, until you see the login status display as Connected. G.Click the Apply button to continue.
Dual-Band Wireless Access Point • If the Router is configured correctly, check your Internet connection (DSL/cable modem, etc.) to see if it is working correctly. You can remove the Router to verify a direct connection. • Manually configure the TCP/IP settings with a DNS address provided by your ISP. • Make sure that your browser is set to connect directly and that any dial-up is disabled. For Internet Explorer, click Tools, Internet Options, and then the Connection tab.
Dual-Band Wireless Access Point never transmitted on the Internet. Furthermore, NAT allows the Router to be used with low cost Internet accounts, such as DSL or cable modems, when only one TCP/IP address is provided by the ISP. The user may have many private addresses behind this single address provided by the ISP.
Dual-Band Wireless Access Point Force your Ethernet adapter to 10Mbps or half duplex mode, and turn off the “Auto-negotiate” feature of your Ethernet adapter as a temporary measure. (Please look at the Network Control Panel in your Ethernet adapter’s Advanced Properties tab.) Make sure that your proxy setting is disabled in the browser. Check our website at www.linksys.com for more information.
Dual-Band Wireless Access Point Is the Router cross-platform compatible? Any platform that supports Ethernet and TCP/IP is compatible with the Router. How many ports can be simultaneously forwarded? Theoretically, the Router can establish 520 sessions at the same time, but you can only forward 10 ranges of ports. Does the Router replace a modem? Is there a cable or DSL modem in the Router? No, the Router must work in conjunction with a cable or DSL modem.
Dual-Band Wireless Access Point •CSMA/CA plus Acknowledge protocol •Multi-Channel Roaming •Automatic Rate Selection •RTS/CTS feature •Fragmentation •Power Management What is ad-hoc mode? When a wireless network is set to ad-hoc mode, the wireless-equipped computers are configured to communicate directly with each other. The ad-hoc wireless network will not communicate with any wired network.
Dual-Band Wireless Access Point worldwide. This presents a truly revolutionary opportunity to place convenient high-speed wireless capabilities in the hands of users around the globe. What is Spread Spectrum? Spread Spectrum technology is a wideband radio frequency technique developed by the military for use in reliable, secure, mission-critical communications systems. It is designed to trade off bandwidth efficiency for reliability, integrity, and security.
Dual-Band Wireless Access Point If you are using the Router and one or more Access Points in close proximity to one another, and they are set on the same channel, interference will be generated. To avoid interference, be sure to set the Router and all Access Points to different channels (frequencies); in other words, assign a unique channel to the Router and each Access Point. How do I reset the Router? Press the Reset button on the back panel for about ten seconds.
Dual-Band Wireless Access Point Appendix H: Regulatory Information FCC STATEMENT This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Dual-Band Wireless Access Point Appendix G: Warranty Information LIMITED WARRANTY Linksys warrants to the original end user purchaser ("You") that, for a period of [ ], (the "Warranty Period") Your Linksys product will be free of defects in materials and workmanship under normal use. Your exclusive remedy and Linksys's entire liability under this warranty will be for Linksys at its option to repair or replace the product or refund Your purchase price less any rebates.
Dual-Band Wireless Access Point Appendix F: Specifications Standards IEEE 802.3, 802.3u, 802.11a and 802.11b Channels 802.11a 802.11b Ports/Buttons One 10/100 RJ-45 Port, One Power Port, One Reset Button, One Power Switch Cabling Type UTP CAT 5 or better Data Rate Up to 54Mbps (up to 72 Mbps in Turbo Mode) Transmit Power 802.11a 802.11b LEDs Power, Diag 802.11a: Act, Link 802.11b: Act, Link LAN: Link/Act, Full/Col, 100 Dimensions (L x W x H) 7.31" x 1.88" x 6.
Dual-Band Wireless Access Point Appendix E: Glossary 802.11a - An IEEE wireless networking standard that specifies a maximum data transfer rate of 54Mbps and an operating frequency of 5GHz. 802.11b - An IEEE wireless networking standard that specifies a maximum data transfer rate of 11Mbps and an operating frequency of 2.4GHz. (Draft) 802.11g - A proposed IEEE wireless networking standard that specifies a maximum data transfer rate of 54Mbps, an operating frequency of 2.
Dual-Band Wireless Access Point Appendix D: Windows Help All wireless products require Microsoft Windows. Windows is the most used operating system in the world and comes with many features that help make networking easier. These features can be accessed through Windows Help and are described in this appendix. TCP/IP Before a computer can communicate with the Access Point, TCP/IP must be enabled. TCP/IP is a set of instructions, or protocol, all PCs follow to communicate over a network.
Dual-Band Wireless Access Point Appendix C: Upgrading Firmware The Access Point's firmware is upgraded through the Web-Utility's Firmware Upgrade tab from the Administration tab. Follow these instructions: 1. Click the Browse button to find the firmware upgrade file that you downloaded from the Linksys website and then extracted. 2. Double-click the firmware file you downloaded and extracted. Click the Upgrade button, and follow the instructions there.
Dual-Band Wireless Access Point Appendix B: Wireless Security A Brief Overview Whenever data - in the form of files, emails, or messages - is transmitted over your wireless network, it is open to attacks. Wireless networking is inherently risky because it broadcasts information on radio waves. Just like signals from your cellular or cordless phone can be intercepted, signals from your wireless network can also be compromised. What are the risks inherent in wireless networking? Read on.
Dual-Band Wireless Access Point Chapter I: Contact Information Need to contact Linksys? Visit us online for information on the latest products and updates to your existing products at: http://www.linksys.com or ftp.linksys.
