User's Manual

42
Appendix G: Regulatory Information
Wireless-G Notebook Adapter
Appendix G: Regulatory Information
FCC STATEMENT
This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used according to the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which is found by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment or devices
Connect the equipment to an outlet other than the receiver's
Consult a dealer or an experienced radio/TV technician for assistance
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator and your body.
INDUSTRY CANADA (CANADA)
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
The use of this device in a system operating either partially or completely outdoors may require the user to obtain
a license for the system according to the Canadian regulations.
EC DECLARATION OF CONFORMITY (EUROPE)
Linksys declares that the Wireless-G Notebook Adapter conforms to the specifications listed below, following the
provisions of the European R&TTE directive 1999/5/EC:
EN 301 489-1, 301 489-17 General EMC requirements for Radio equipment.
EN 609 50 Safety
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
T
hese limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
g
enerates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
h
armful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
I
f this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off
a
nd on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
T
his device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
h
armful interference, and (2) this device must accept any interference received, including interference that may cause undesired
o
peration.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's
a
uthority to operate this equipment.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
This device is intended only for OEM integrators under the following conditions:
1
) The transmitter module may not be co-located with any other transmitter or antenna.
A
s long as conduction above is met, further transmitter test will not be required. However, the OEM integrator is still responsible for
t
esting their end-product for any additional compliance requirements required with this module installed (for example, digital device
e
missions, PC peripheral requirements, etc.).
I
MPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with
a
nother transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In
t
hese circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a
s
eparate FCC authorization.
E
nd Product Labeling
T
he final end product must be labeled in a visible area with the following: “Contains TX FCC ID:Q87-WPC54GV4''
M
anual Information That Must be Included
T
he OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the
u
sers manual of the end product which integrate this module.
T
he users manual for OEM integrators must include the following information in a prominent location “ IMPORTANT NOTE: To comply
w
ith FCC RF exposure compliance requirements. The antenna must not be co-located or operating in conjunction with any other antenna
o
r transmitter.
E
C DECLARATION OF CONFORMITY (EUROPE)
L
inksys declares that the Wireless-G Notebook Adapter conforms to the specifications listed below, following the
p
rovisions of the European R&TTE directive 1999/5/EC:
E
N 301 489-1, 301 489-17 General EMC requirements for Radio equipment.
E
N 609 50 Safety