2.4 GHz Wireless-G 802.11g Exterior Access Point WIRELESS Model No.
Wireless-G Exterior Access Point Copyright and Trademarks Specifications are subject to change without notice. Linksys is a registered trademark or trademark of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Copyright © 2006 Cisco Systems, Inc. All rights reserved. Other brands and product names are trademarks or registered trademarks of their respective holders.
Wireless-G Exterior Access Point Table of Contents Chapter 1: Introduction Welcome What’s in this User Guide? 1 1 2 Chapter 2: Planning Your Wireless Network 4 Network Topology Roaming Network Layout Example of a Simple Wireless Network 4 4 4 5 Chapter 3: Getting to Know the Wireless-G Exterior Access Point The LEDs The Ports The Reset Button and Ground The Antenna Pattern Chapter 4: Connecting the Wireless-G Exterior Access Point Overview Hardware Installation Chapter 5: Setting Up the Wireless-G
Wireless-G Exterior Access Point The Administration - Reboot Tab The Administration - Config Management Tab The Status - Local Network Tab The Status - Wireless Tab The Status - System Performance Tab 37 38 39 40 41 Appendix A: Troubleshooting 43 Frequently Asked Questions 43 Appendix B: Wireless Security Security Precautions Security Threats Facing Wireless Networks Appendix C: Upgrading Firmware Appendix D: Windows Help Appendix E: Glossary Appendix F: Specifications Appendix G: Warranty Informati
Wireless-G Exterior Access Point List of Figures Figure 2-1: Example of a Simple Wireless Network Figure 3-1: Front Panel Figure 3-2: Bottom Panel Figure 3-3: Top Panel Figure 3-4: Back Panel Figure 3-5: Internal Antenna Pattern (Horizontal Plane) Figure 3-6: Radio Coverage of the Access Point to Client Devices Figure 3-7: Access Point to Access Point (bridging) Radio Coverage Figure 4-1: Mark the Locations of the Two Wall-Mount Slots Figure 4-2: Attach the Mounting Plate Figure 4-3: Ground the Access Poin
Wireless-G Exterior Access Point Figure 6-15: Wireless - Advanced Wireless Figure 6-16: AP Mode Figure 6-17: Wireless Repeater Figure 6-18: Site Survey Figure 6-19: Administration - Management Figure 6-20: The Administration - Log Figure 6-21: Administration - Factory Default Figure 6-22: Administration - Firmware Upgrade Figure 6-23: Administration - Reboot Figure 6-24: Administration - Config Management Figure 6-25: Status - Local Network Figure 6-26: Status - Wireless Figure 6-27: Status - System Perfor
Wireless-G Exterior Access Point Chapter 1: Introduction Welcome Thank you for choosing the Wireless-G Exterior Access Point. This Access Point will allow you to network wirelessly better than ever. How does the Access Point do all of this? An access point allows for greater range and mobility within your wireless network while also allowing you to connect the wireless network to a wired environment.
Wireless-G Exterior Access Point What’s in this User Guide? This user guide covers the steps for setting up and using the Wireless-G Exterior Access Point. • Chapter 1: Introduction This chapter describes the Wireless-G Exterior Access Point’s applications and this User Guide. • Chapter 2: Planning your Wireless Network This chapter describes the basics of wireless networking. • Chapter 3: Getting to Know the Wireless-G Exterior Access Point This chapter describes the physical features of the Access Point.
Wireless-G Exterior Access Point • Appendix G: Warranty Information This appendix supplies the Access Point’s warranty information. • Appendix H: Regulatory Information This appendix supplies the Access Point’s regulatory information. • Appendix I: Contact Information This appendix provides contact information for a variety of Linksys resources, including Technical Support.
Wireless-G Exterior Access Point Chapter 2: Planning Your Wireless Network Network Topology A wireless network is a group of computers, each equipped with one or more wireless adapters. Computers in a wireless network must be configured to share the same radio channel to talk to each other. Several PCs equipped with wireless cards or adapters can communicate with each other to form an ad-hoc network without the use of an access point.
Wireless-G Exterior Access Point To link your wired network with your wireless network, connect the Access Point’s Ethernet network port to any switch or router with Power over Ethernet (PoE)—or a PoE injector, such as the Linksys WAPPOE or WAPPOE12. Note that 12 VDC on WAPPOE12 is for the splitter output. Both PoE Injectors provide 48 VDC power output. With these and many other Linksys products, your networking options are limitless. Go to the Linksys website at www.linksys.
Wireless-G Exterior Access Point Chapter 3: Getting to Know the Wireless-G Exterior Access Point The LEDs The Access Point's LEDs, where information about network activity is displayed, are located on the front panel. Figure 3-1: Front Panel Power Green. The power LED lights up when the Access Point is powered on. Wired Green. The Wired LED lights up when the Access Point is successfully connected to a device through the Ethernet network port.
Wireless-G Exterior Access Point The Ports The Access Point's Ethernet network port is located on the bottom panel and the antenna port is located on the top panel. port: the connection point on a computer or networking device used for plugging in cables or adapters Figure 3-2: Bottom Panel Ethernet The Ethernet network port connects to Ethernet network devices, such as a switch or router that supports Power over Ethernet (PoE).
Wireless-G Exterior Access Point The Reset Button and Ground The Access Point's Reset button and ground are located on the back panel. Reset Button Ground Figure 3-4: Back Panel Reset Button There are two ways to Reset the Access Point's factory defaults. Either press the Reset button, for approximately ten seconds, or restore the defaults using the Access Point's Webbased Utility.
Wireless-G Exterior Access Point The Antenna Pattern Figure 3-5: Internal Antenna Pattern (Horizontal Plane) The above diagram shows the antenna pattern of the built-in directional antenna on the horizontal plane. The power of the wireless signal is most strong on the direction perpendicular to the front surface (with Linksys logo) of the Access Point. The peak gain of this antenna is 9dBi. The 3dB beamwidth is 47 degrees.
Wireless-G Exterior Access Point Figure 3-6: Radio Coverage of the Access Point to Client Devices When using the Access Point to connect client devices, adjust it so the client devices are on the same horizontal plane as the Access Point and within a 3dB angle of 47 degrees. This will ensure the strongest signal and maximum reach. If the Access Point is used inside a building, put it in a corner of the building for maximum coverage.
Wireless-G Exterior Access Point Figure 3-7: Access Point to Access Point (bridging) Radio Coverage If the Access Point is used as a bridge or repeater, adjust the Access Points to face each other to ensure the strongest signal and maximum reach. Make sure that the orientation of the two Directional Antennas is the same. The radio wave is polarized so a 90 degree rotation will result in no received power.
Wireless-G Exterior Access Point Chapter 4: Connecting the Wireless-G Exterior Access Point Overview hardware: the physical aspect of computers, telecommunications, and other information technology devices. This chapter explains how to mount and connect the Access Point. Depending on your application, you might want to set up the IP address of the device first before mounting the device. Refer to "Chapter 5: Setting Up the Wireless-G Exterior Access Point". Hardware Installation 1.
Wireless-G Exterior Access Point 6. Make sure that you properly ground the Access Point. 7. Line up the Access Point’s wall-mount slots with the two screws on the wall. Then, slide the Access Point down so that the screws fit snugly in the slots. 8. Attach a screw (not included) in each of the two holes on the top of the mounting plate so that the Access Point is securely mounted to the wall. 9.
Wireless-G Exterior Access Point Chapter 5: Setting Up the Wireless-G Exterior Access Point Overview The Access Point has been designed to be functional right out of the box with the default settings. However, if you'd like to change these settings, the Access Point can be configured through your web browser with the Webbased Utility. This chapter explains how to use the Utility. HAVE YOU: Enabled TCP/IP on your PCs? PCs communicate over the network with this protocol.
Wireless-G Exterior Access Point (192.168.1.245). Or if there is DHCP server connected to the switch, configure it to assign the IP address in 192.168.1.0/24 subnet. Your PC will get an IP address in the subnet through the DHCP. 3. It is not recommended to use it this way, but you can connect your PC wirelessly to the Access Point when the DHCP server is connected on the LAN side. It is not recommended because you can easily lose your connection through configuration changes.
Wireless-G Exterior Access Point AP Mode Use this screen to configure the Access Point operation mode with WDS (Wireless Distribution System). Administration You will use the Administration tabs to manage the Access Point. • Management. This screen allows you to customize the password and Simple Network Management Protocol (SNMP) settings. snmp: the standard network management protocol on the Internet. • Log. Configure the Log settings for the Access Point on this screen. • Factory Default.
Wireless-G Exterior Access Point Chapter 6: Configuring the Wireless-G Exterior Access Point This chapter is a detailed reference guide for the Web-based Utility. You do not need the Utility to start using your Access Point. The Access Point has been designed to be functional right out of the box with the default settings. However, if you'd like to change your settings, you can use the Utility. The Setup Tab The first screen that appears is the Setup screen.
Wireless-G Exterior Access Point Select Automatic Configuration - DHCP if you have a DHCP server enabled on the LAN that can assign an IP address to the Access Point. Change these settings as described here and click Save Settings to apply your changes, or click Cancel Changes to cancel your changes. Help information is displayed on the right-hand side of the screen. The Setup - Time Tab This allows you to change the Access Point's time settings.
Wireless-G Exterior Access Point The Wireless - Basic Wireless Settings Tab Change the basic wireless network settings on this screen. The Access Point can connect to up to eight wireless networks (SSIDs) at the same time, so this screen offers settings for up to eight different SSIDs. All the SSIDs share the same BSSID (MAC address) on this Access Point, so the first one is called Main SSID and others are called Virtual SSIDs. Wireless Network Configure the Wireless Network attributes for each SSID.
Wireless-G Exterior Access Point Tx Rate Limiting. You can limit the maximum data rate used in your network to save bandwidth and power consumption on client devices. The actual data rate is determined by an Auto-Fallback mechanism between your Access Point and a client device. The default is 54 Mbps Mixed or G-Only mode, 11 Mbps for B-Only mode. Wireless SSID Broadcast. The default is Enabled. This option allows the primary SSID to be broadcast on your network.
Wireless-G Exterior Access Point The Wireless - Wireless Security Tab Change the Access Point’s wireless security settings on this screen. Wireless Security Enter the security settings for each SSID of the Access Point. Select SSID. Select the SSID whose security settings you want to configure. Security Mode. Select the wireless security mode you want to use, WPA-Personal, WPA2-Personal, WPA2Personal Mixed, WPA-Enterprise, WPA2-Enterprise, WPA2-Enterprise Mixed, RADIUS, or WEP.
Wireless-G Exterior Access Point WPA2-Personal WPA Algorithms. WPA2 always uses AES for data encryption. WPA Shared Key. Enter a WPA Shared Key of 8-63 characters. Key Renewal Timeout. Enter a Key Renewal Timeout period, which instructs the Access Point how often it should change the encryption keys. The default is 3600 seconds. WPA2-Personal Mixed This security mode supports the transition from WPA-Personal to WPA2-Personal. You can have client devices that use either WPA-Personal or WPA2-Personal.
Wireless-G Exterior Access Point WPA-Enterprise This option features WPA used in coordination with a RADIUS server for client authentication. (This should only be used when a RADIUS server is connected to the Access Point.) RADIUS Server IP Address. Enter the RADIUS server’s IP address. RADIUS Server Port. Enter the port number used by the RADIUS server. The default is 1812. WPA Algorithms. WPA offers you two encryption methods, TKIP and AES for data encryption.
Wireless-G Exterior Access Point WPA2-Enterprise Mixed This security mode supports the transition from WPA-Enterprise to WPA2-Enterprise. You can have client devices that use either WPA-Enterprise or WPA2-Enterprise. The Access Point will automatically choose the encryption algorithm used by each client device. RADIUS Server IP Address. Enter the RADIUS server’s IP address. RADIUS Server Port. Enter the port number used by the RADIUS server. The default is 1812. WPA Algorithms.
Wireless-G Exterior Access Point RADIUS This security mode is also known as Dynamic WEP with IEEE 802.1X. The RADIUS server is used for client authentication and WEP is used for data encryption. The WEP key is automatically generated by the RADIUS server. A manual WEP key is no longer compatible with Microsoft Windows implementation (due to its weak authentication capability). RADIUS Server IP Address. Enter the RADIUS server’s IP address. RADIUS Server Port.
Wireless-G Exterior Access Point The Wireless - Wireless Connection Control Tab This screen allows you to configure the Connection Control List to control the connection (association) of wireless client devices. Wireless Connection Control Connection Control. Choose one of the three options to control the connection (association) of wireless client devices. • Disabled. The default setting. • Prevent MAC Addresses (specific client devices) from connecting to the Access Point.
Wireless-G Exterior Access Point The Wireless - Advanced Wireless Settings Tab This screen allows you to configure the advanced settings for the Access Point. Advanced Wireless You can change the data transmission and output power settings for the Access Point. CTS Protection Mode. CTS (Clear-To-Send) Protection Mode function boosts the Access Point’s ability to catch all Wireless-G transmissions but will severely decrease performance.
Wireless-G Exterior Access Point Fragmentation Threshold. This specifies the maximum size a data packet can be before splitting and creating a new packet. It should remain at its default setting of 2346. A smaller setting means smaller packets, which creates more packets for each transmission. If you experience high packet error rates, you can decrease this value, but it will likely decrease overall network performance. Only minor modifications of this value are recommended. Power Output.
Wireless-G Exterior Access Point The AP Mode Tab On this screen you can change the Access Point’s mode of operation. It is also known as WDS (Wireless Distribution System) Mode. You may wish to do this if you want to use the Access Point as a wireless repeater to extend the range of your wireless network.
Wireless-G Exterior Access Point Wireless Repeater When set to Wireless Repeater mode, the Access Point receives the signal from the remote Access Point and retransmits its signal. (This feature only works with the Linksys Wireless-G Exterior Access Point (model number: WAP54GPE), Wireless-G Interior Access Point (model number: WAP54GP), Wireless-G Access Point (model number: WAP54G), and Wireless-G Broadband Router (model number: WRT54G).
Wireless-G Exterior Access Point Wireless Bridge This mode connects multiple physically separated wired networks with access points. If you are trying to create a wireless connection between two wired networks, select Wireless Bridge and enter the MAC addresses of the remote wireless bridge/access point in the MAC 1 fields. If you do not know the remote wireless bridge/access point’s MAC address, click the Site Survey button.
Wireless-G Exterior Access Point The Administration - Management Tab On this screen you can configure the password, Web Access, and SNMP settings. AP Password You should change the username/password that controls access to the Access Point’s Web-based Utility. Local AP Password User Name. Modify the administrator username. The default is admin. AP Password. Modify the administrator password for the Access Point’s Web-based Utility. The default is admin. Re-enter to confirm.
Wireless-G Exterior Access Point Device Name. Enter the name you wish to give to the Access Point. Location. Enter the location of the Access Point. Get Community. Enter the password that allows read-only access to the Access Point’s SNMP information. The default is public. Set Community. Enter the password that allows read/write access to the Access Point’s SNMP information. The default is private. SNMP Trap-Community.
Wireless-G Exterior Access Point The Administration - Log Tab On this screen you can configure the log settings and alerts of particular events. Log You can have logs that keep track of the Access Point’s activities. Email Alert E-Mail Alert. If you want the Access Point to send e-mail alerts in the event of certain attacks, select Enabled. The default is Disabled. E-Mail Address for Logs. Enter the e-mail address that will receive logs.
Wireless-G Exterior Access Point System Error Messages. If you want to log system error messages, click the checkbox. Configuration Changes. If you want to log any configuration changes, click the checkbox. Change these settings as described here and click Save Settings to apply your changes, or click Cancel Changes to cancel your changes. Help information is displayed on the right-hand side of the screen, and click More for additional details.
Wireless-G Exterior Access Point The Administration - Factory Default Tab On this screen you can restore the Access Point’s factory default settings. Factory Default Note any custom settings before you restore the factory defaults. Once the Access Point is reset, you will have to re-enter all of your configuration settings. Restore Factory Defaults. To restore the Access Point's factory default settings, click the Yes radio button. Then click Save Settings.
Wireless-G Exterior Access Point The Administration - Reboot Tab On this screen you can reboot the Access Point. Reboot This feature is useful when you need to remotely reboot the Access Point. Device Reboot. To reboot the Access Point, click the Yes radio button. Click Save Settings to apply your change and the Access Point will reboot itself, or click Cancel Changes to cancel your change. Help information is displayed on the right-hand side of the screen.
Wireless-G Exterior Access Point The Administration - Config Management Tab On this screen you can create a backup configuration file or save a configuration file to the Access Point. Config Management Use this screen to upload or download configuration files for the Access Point. Save Configuration. To save a backup configuration file on a computer, click the Save Configuration to File button and follow the on-screen instructions. Restore Configuration.
Wireless-G Exterior Access Point The Status - Local Network Tab The Local Network screen displays the Access Point’s current status information for the local network. Information Hardware Version. This is the version of the Access Point’s current hardware. Software Version. This is the version of the Access Point’s current software. Local MAC Address. The MAC address of the Access Point’s Local Area Network (LAN) interface is displayed here. System Up Time.
Wireless-G Exterior Access Point The Status - Wireless Tab The Wireless screen displays the Access Point’s current status information for the wireless network(s). Wireless Network MAC Address. The MAC Address of the Access Point’s wireless interface is displayed here. Mode. The Access Point’s wireless network mode is displayed here. Main SSID. The Access Point’s primary SSID is displayed here. Virtual SSID1-7. The Access Point’s alternative SSIDs are displayed here. Channel.
Wireless-G Exterior Access Point The Status - System Performance Tab The System Performance screen displays the Access Point’s status information for its current settings and data transmissions. System Performance Wired Name. This indicates that the statistics are for the wired network, the LAN. IP Address. The Access Point’s local IP address is displayed here. MAC Address. This shows the MAC Address of the Access Point’s wired interface. Connection.
Wireless-G Exterior Access Point Packets Sent. This shows the number of packets sent for each wireless network. Bytes Received. This shows the number of bytes received for each wireless network. Bytes Sent. This shows the number of bytes sent for each wireless network. Error Packets Received. This shows the number of error packets received for each wireless network. Drop Received Packets. This shows the number of packets being dropped after they were received.
Wireless-G Exterior Access Point Appendix A: Troubleshooting This appendix provides solutions to problems that may occur during the installation and operation of the Wireless-G Exterior Access Point. Read the description below to solve your problems. If you can't find an answer here, check the Linksys website at www.linksys.com. Frequently Asked Questions Can the Access Point act as my DHCP Server? No.
Wireless-G Exterior Access Point What IEEE 802.11g features are supported? The product supports the following IEEE 802.11g functions: • CSMA/CA plus Acknowledge protocol • OFDM protocol • Multi-Channel Roaming • Automatic Rate Selection • RTS/CTS feature • Fragmentation • Power Management What is Ad-hoc? An Ad-hoc wireless LAN is a group of computers, each with a WLAN adapter, connected as an independent wireless LAN.
Wireless-G Exterior Access Point What is the ISM band? The FCC and their counterparts outside of the U.S. have set aside bandwidth for unlicensed use in the ISM (Industrial, Scientific and Medical) band. Spectrum in the vicinity of 2.4 GHz, in particular, is being made available worldwide. This presents a truly revolutionary opportunity to place convenient high speed wireless capabilities in the hands of users around the globe.
Wireless-G Exterior Access Point What is a MAC Address? The Media Access Control (MAC) address is a unique number assigned by the manufacturer to any Ethernet networking device, such as a network adapter, that allows the network to identify it at the hardware level. For all practical purposes, this number is usually permanent. Unlike IP addresses, which can change every time a computer logs on to the network, the MAC address of a device stays the same, making it a valuable identifier for the network.
Wireless-G Exterior Access Point Appendix B: Wireless Security Linksys wants to make wireless networking as safe and easy for you as possible. The current generation of Linksys products provide several network security features, but they require specific action on your part for implementation. So, keep the following in mind whenever you are setting up or using your wireless network.
Wireless-G Exterior Access Point SSID. There are several things to keep in mind about the SSID: 1. Disable Broadcast 2. Make it unique 3. Change it often Most wireless networking devices will give you the option of broadcasting the SSID. While this option may be more convenient, it allows anyone to log into your wireless network. This includes hackers. So, don’t broadcast the SSID. Wireless networking products come with a default SSID set by the factory. (The Linksys default SSID is “linksys”.
Wireless-G Exterior Access Point WPA Enterprise. If you do not have a RADIUS server, select the type of algorithm, TKIP or AES, enter a password in the Pre-Shared key field of 8-64 characters, and enter a Group Key Renewal period time between 0 and 99,999 seconds, which instructs the Router or other device how often it should change the encryption keys. WPA RADIUS. WPA used in coordination with a RADIUS server. (This should only be used when a RADIUS server is connected to the Router or other device.
Wireless-G Exterior Access Point Appendix C: Upgrading Firmware The Access Point's firmware is upgraded through the Web-based Utility’s Administration - Firmware Upgrade tab. Follow these instructions: 1. Download the firmware upgrade file from the Linksys website, www.linksys.com. 2. Extract the firmware upgrade file on your computer. 3. Open the Access Point’s Web-based Utility. 4. Click the Administration tab. 5. Click the Upgrade Firmware tab. 6.
Wireless-G Exterior Access Point Appendix D: Windows Help Almost all wireless products require Microsoft Windows. Windows is the most used operating system in the world and comes with many features that help make networking easier. These features can be accessed through Windows Help and are described in this appendix. TCP/IP Before a computer can communicate with the Access Point, TCP/IP must be enabled. TCP/IP is a set of instructions, or protocol, all PCs follow to communicate over a network.
Wireless-G Exterior Access Point Appendix E: Glossary This glossary contains some basic networking terms you may come across when using this product. For more advanced terms, see the complete Linksys glossary at http://www.linksys.com/glossary. Access Point - A device that allows wireless-equipped computers and other devices to communicate with a wired network. Also used to expand the range of a wireless network.
Wireless-G Exterior Access Point DMZ (Demilitarized Zone) - Removes the Router's firewall protection from one PC, allowing it to be "seen" from the Internet. DNS (Domain Name Server) - The IP address of your ISP's server, which translates the names of websites into IP addresses. Domain - A specific name for a network of computers. Download - To receive a file transmitted over a network. DSL (Digital Subscriber Line) - An always-on broadband connection over traditional phone lines.
Wireless-G Exterior Access Point IP Address - The address used to identify a computer or device on a network. IPCONFIG - A Windows 2000 and XP utility that displays the IP address for a particular networking device. IPSec (Internet Protocol Security) - A VPN protocol used to implement secure exchange of packets at the IP layer. ISP (Internet Service Provider) - A company that provides access to the Internet. LAN - The computers and networking products that make up your local network.
Wireless-G Exterior Access Point RJ-45 (Registered Jack-45) - An Ethernet connector that holds up to eight wires. Roaming - The ability to take a wireless device from one access point's range to another without losing the connection. Router - A networking device that connects multiple networks together. Server - Any computer whose function in a network is to provide user access to files, printing, communications, and other services.
Wireless-G Exterior Access Point TKIP (Temporal Key Integrity Protocol) - a wireless encryption protocol that provides dynamic encryption keys for each packet transmitted. Topology - The physical layout of a network. TX Rate - Transmission Rate. Upgrade - To replace existing software or firmware with a newer version. Upload - To transmit a file over a network. URL (Uniform Resource Locator) - The address of a file located on the Internet.
Wireless-G Exterior Access Point Appendix F: Specifications Model WAP54GPE Standards IEEE802.11g, IEEE802.11b, IEEE802.3u, IEEE802.3af Ports 1 Ethernet,1 External Antenna* Buttons Reset Cabling Type UTP CAT 5 LEDs Power, Ethernet, Wireless Transmit Power 18 dBm for 802.11b, 14 dBm for 802.11g Security Features WEP, WPA, WPA2, RADIUS WEP Key Bits 64, 128 Dimensions (W x H x D) 6.42" x 8.07" x 2.17" (163 mm x 205 mm x 55 mm) Unit Weight 2.5 lbs. (1.14 kg) Power IEEE802.
Wireless-G Exterior Access Point Operating Humidity 5% to 95%, Non-Condensing Storage Humidity 5% to 95%, Non-Condensing * External antenna is sold separately Appendix F: Specifications 58
Wireless-G Exterior Access Point Appendix G: Warranty Information LIMITED WARRANTY Linksys warrants to You that, for a period of three years (the “Warranty Period”), your Linksys Product will be substantially free of defects in materials and workmanship under normal use. Your exclusive remedy and Linksys' entire liability under this warranty will be for Linksys at its option to repair or replace the Product or refund Your purchase price less any rebates.
Wireless-G Exterior Access Point Appendix H: Regulatory Information FCC Statement This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Wireless-G Exterior Access Point Règlement d’Industry Canada Le fonctionnement est soumis aux conditions suivantes : 1. Ce périphérique ne doit pas causer d'interférences; 2. Ce périphérique doit accepter toutes les interférences reçues, y compris celles qui risquent d'entraîner un fonctionnement indésirable.
Wireless-G Exterior Access Point Appendix H: Regulatory Information 62
Wireless-G Exterior Access Point Appendix H: Regulatory Information 63
Wireless-G Exterior Access Point Appendix H: Regulatory Information 64
Dual-Band Wireless Access Point For more information, visit www.linksys.com.
Wireless-G Exterior Access Point Appendix I: Contact Information Need to contact Linksys? Visit us online for information on the latest products and updates to your existing products at: http://www.linksys.com or ftp.linksys.
