Instruction Manual
Table Of Contents
- Preface
- Introducing Linksys IP Phones
- Getting Started
- Managing Linksys IP Phones
- Using the 900 Series LCD Display
- Localization
- Changing the Display Background (SPA942/962)
- Using the SPA932 (Sidecar) with the SPA962
- Configuring the Web Service
- RSS Newsfeeds (SPA962)
- Call Appearances and Extensions
- Line Key LEDs
- Using Call Features
- Selecting the Audio I/O Device and Line
- Making Calls
- Answering and Ending Calls
- Hold and Resume
- Call Waiting
- Speed Dialing
- Three-Way Conferencing
- Attended Call Transfer
- Blind Call Transfer
- Call Back
- Message Waiting Indication (MWI)
- Accessing Voicemail
- Muting Calls
- Shared Call Appearances
- Personal Directory
- Caller and Called Name Matching
- Dialing Assistance
- Supplementary Services
- Call Logs
- Audio Volume Adjustment
- Managing Ring Tones
- Configuring a Dial Plan
- System Administration
- Troubleshooting FAQ
- SPA900 Series LCD Command Reference
- Entering Names and Numbers into the Directory
- Entering Directory Names, Numbers and Ring Default
- 2 Speed Dial
- 3 Call History
- 4 Ring Tone
- 5 Preferences
- 6 Call Forward
- 7 Time/Date
- 8 Voice Mail
- 9 Network
- 9.1 DCHP
- 9.2 Current IP Address
- 9.3 Host Name
- 9.4 Domain
- 9.5 Current NetMask
- 9.6 Current Gateway
- 9.7 Enable Web Server
- 9.8 Non DHCP IP Address
- 9.9 Non DHCP Subnet Mask
- 9.10 Non DHCP Default Route
- 9.11 Non DHCP DNS 1
- 9.12 Non DHCP DNS 2
- 9.13 Non DHCP NTP Server 1
- 9.14 Non DHCP NTP Server 2
- 9.15 Multicast Address
- 9.16 Enable VLAN
- 9.17 VLAN ID
- 9.18 CDP
- 10 Product Info
- 11 Status
- 12 Reboot
- 13 Restart
- 14 Factory Reset
- 15 Custom Reset
- 16 Set Password
- 17 Set LCD Contrast
- 18 CallPark Status
- 19 Language (SPA922, 942, and 962)
- 20 GUI Properties (SPA962)
- 21 Web Service (SPA962)
- Linksys IP Phone Field Reference
- Acronyms
- Glossary
5-24
Linksys IP Phone Administrator Guide
Firmware Version 5.1
Chapter 5 Linksys IP Phone Field Reference
Regional Tab
Secure One Call Act Code Makes the next outbound call secure. (It is redundant if all outbound calls are secure by
default.)
Defaults to *18.
Secure One Call Deact Code Makes the next outbound call not secure. (It is redundant if all outbound calls are not
secure by default.)
Defaults to *19.
Paging Code The star code used for paging the other clients in the group.
Defaults to *96.
Call Park Code The star code used for parking the current call.
Defaults to *38.
Call Pickup Code The star code used for picking up a ringing call.
Defaults to *36.
Call UnPark Code The star code used for picking up a call from the call park.
Defaults to *39.
Group Call Pickup Code The star code used for picking up a group call.
Defaults to *37.
Media Loopback Code The star code used for media loopback.
Defaults to *03.
Referral Services Codes These codes tell the Linksys IP phone what to do when the user places the current call on
hold and is listening to the second dial tone.
One or more *code can be configured into this parameter, such as *98, or *97|*98|*123,
etc. Max total length is 79 chars. This parameter applies when the user places the current
call on hold (by Hook Flash) and is listening to second dial tone. Each *code (and the
following valid target number according to current dial plan) entered on the second
dial-tone triggers the Linksys IP phone to perform a blind transfer to a target number that
is prepended by the service *code.
For example, after the user dials *98, the Linksys IP phone plays a special dial tone called
the Prompt Tone while waiting for the user the enter a target number (which is checked
according to dial plan as in normal dialing). When a complete number is entered, the
Linksys IP phone sends a blind REFER to the holding party with the Refer-To target
equals to *98<target_number>. This feature allows the Linksys IP phone to hand off a call
to an application server to perform further processing, such as call park.
The *codes should not conflict with any of the other vertical service codes internally
processed by the Linksys IP phone. You can empty the corresponding *code that you do
not want to Linksys IP phone to process.
Field Description