Instruction Manual
Table Of Contents
- Preface
- Introducing Linksys IP Phones
- Getting Started
- Managing Linksys IP Phones
- Using the 900 Series LCD Display
- Localization
- Changing the Display Background (SPA942/962)
- Using the SPA932 (Sidecar) with the SPA962
- Configuring the Web Service
- RSS Newsfeeds (SPA962)
- Call Appearances and Extensions
- Line Key LEDs
- Using Call Features
- Selecting the Audio I/O Device and Line
- Making Calls
- Answering and Ending Calls
- Hold and Resume
- Call Waiting
- Speed Dialing
- Three-Way Conferencing
- Attended Call Transfer
- Blind Call Transfer
- Call Back
- Message Waiting Indication (MWI)
- Accessing Voicemail
- Muting Calls
- Shared Call Appearances
- Personal Directory
- Caller and Called Name Matching
- Dialing Assistance
- Supplementary Services
- Call Logs
- Audio Volume Adjustment
- Managing Ring Tones
- Configuring a Dial Plan
- System Administration
- Troubleshooting FAQ
- SPA900 Series LCD Command Reference
- Entering Names and Numbers into the Directory
- Entering Directory Names, Numbers and Ring Default
- 2 Speed Dial
- 3 Call History
- 4 Ring Tone
- 5 Preferences
- 6 Call Forward
- 7 Time/Date
- 8 Voice Mail
- 9 Network
- 9.1 DCHP
- 9.2 Current IP Address
- 9.3 Host Name
- 9.4 Domain
- 9.5 Current NetMask
- 9.6 Current Gateway
- 9.7 Enable Web Server
- 9.8 Non DHCP IP Address
- 9.9 Non DHCP Subnet Mask
- 9.10 Non DHCP Default Route
- 9.11 Non DHCP DNS 1
- 9.12 Non DHCP DNS 2
- 9.13 Non DHCP NTP Server 1
- 9.14 Non DHCP NTP Server 2
- 9.15 Multicast Address
- 9.16 Enable VLAN
- 9.17 VLAN ID
- 9.18 CDP
- 10 Product Info
- 11 Status
- 12 Reboot
- 13 Restart
- 14 Factory Reset
- 15 Custom Reset
- 16 Set Password
- 17 Set LCD Contrast
- 18 CallPark Status
- 19 Language (SPA922, 942, and 962)
- 20 GUI Properties (SPA962)
- 21 Web Service (SPA962)
- Linksys IP Phone Field Reference
- Acronyms
- Glossary
5-22
Linksys IP Phone Administrator Guide
Firmware Version 5.1
Chapter 5 Linksys IP Phone Field Reference
Regional Tab
Vertical Service Activation Codes
The following Vertical Service Activation Codes are automatically appended to the dial-plan.
Note Some of the following parameters do not apply to the SPA901.
Interdigit Long Timer
(Not applicable to SPA901)
Long timeout between entering digits when dialing. The interdigit timer values are used
as defaults when dialing. The Interdigit_Long_Timer is used after any one digit, if all
valid matching sequences in the dial plan are incomplete as dialed. Range: 0–64 seconds.
Defaults to 10.
Interdigit Short Timer
(Not applicable to SPA901)
Short timeout between entering digits when dialing. The Interdigit_Short_Timer is used
after any one digit, if at least one matching sequence is complete as dialed, but more
dialed digits would match other as yet incomplete sequences. Range: 0–64 seconds.
Defaults to 3.
Field Description
Field Description
Call Return Code This code calls the last caller.
Defaults to *69.
Blind Transfer Code Begins a blind transfer of the current call to the extension specified after the activation
code.
Defaults to *98.
Call Back Act Code Starts a callback when the last outbound call is not busy.
Defaults to *66.
Call Back Deact Code Cancels a callback.
Defaults to *86.
Cfwd All Act Code Forwards all calls to the extension specified after the activation code.
Defaults to *72.
Cfwd All Deact Code Cancels call forwarding of all calls.
Defaults to *73.
Cfwd Busy Act Code Forwards busy calls to the extension specified after the activation code.
Defaults to *90.
Cfwd Busy Deact Code Cancels call forwarding of busy calls.
Defaults to *91.