Instruction Manual
Table Of Contents
- Preface
- Introducing Linksys IP Phones
- Getting Started
- Managing Linksys IP Phones
- Using the 900 Series LCD Display
- Localization
- Changing the Display Background (SPA942/962)
- Using the SPA932 (Sidecar) with the SPA962
- Configuring the Web Service
- RSS Newsfeeds (SPA962)
- Call Appearances and Extensions
- Line Key LEDs
- Using Call Features
- Selecting the Audio I/O Device and Line
- Making Calls
- Answering and Ending Calls
- Hold and Resume
- Call Waiting
- Speed Dialing
- Three-Way Conferencing
- Attended Call Transfer
- Blind Call Transfer
- Call Back
- Message Waiting Indication (MWI)
- Accessing Voicemail
- Muting Calls
- Shared Call Appearances
- Personal Directory
- Caller and Called Name Matching
- Dialing Assistance
- Supplementary Services
- Call Logs
- Audio Volume Adjustment
- Managing Ring Tones
- Configuring a Dial Plan
- System Administration
- Troubleshooting FAQ
- SPA900 Series LCD Command Reference
- Entering Names and Numbers into the Directory
- Entering Directory Names, Numbers and Ring Default
- 2 Speed Dial
- 3 Call History
- 4 Ring Tone
- 5 Preferences
- 6 Call Forward
- 7 Time/Date
- 8 Voice Mail
- 9 Network
- 9.1 DCHP
- 9.2 Current IP Address
- 9.3 Host Name
- 9.4 Domain
- 9.5 Current NetMask
- 9.6 Current Gateway
- 9.7 Enable Web Server
- 9.8 Non DHCP IP Address
- 9.9 Non DHCP Subnet Mask
- 9.10 Non DHCP Default Route
- 9.11 Non DHCP DNS 1
- 9.12 Non DHCP DNS 2
- 9.13 Non DHCP NTP Server 1
- 9.14 Non DHCP NTP Server 2
- 9.15 Multicast Address
- 9.16 Enable VLAN
- 9.17 VLAN ID
- 9.18 CDP
- 10 Product Info
- 11 Status
- 12 Reboot
- 13 Restart
- 14 Factory Reset
- 15 Custom Reset
- 16 Set Password
- 17 Set LCD Contrast
- 18 CallPark Status
- 19 Language (SPA922, 942, and 962)
- 20 GUI Properties (SPA962)
- 21 Web Service (SPA962)
- Linksys IP Phone Field Reference
- Acronyms
- Glossary
5-19
Linksys IP Phone Administrator Guide
Firmware Version 5.1
Chapter 5 Linksys IP Phone Field Reference
Regional Tab
Regional Tab
This section describes the fields for the following headings on the Regional tab:
• Call Progress Tones, page 5-19
• Distinctive Ring Patterns, page 5-20
• Control Timer Values (sec), page 5-21
• Vertical Service Activation Codes, page 5-22
• Vertical Service Activation Codes, page 5-22
• Outbound Call Codec Selection Codes, page 5-25
• Miscellaneous, page 5-27
Call Progress Tones
Note None of the following parameters apply to the SPA901.
Field Description
Dial Tone Prompts the user to enter a phone number.
Defaults to 350@-19,440@-19;10(*/0/1+2).
Outside Dial Tone Alternative to the Dial Tone. It prompts the user to enter an external phone number, as
opposed to an internal extension. It is triggered by a, (comma) character encountered in
the dial plan.
Defaults to 420@-16;10(*/0/1).
Prompt Tone Prompts the user to enter a call forwarding phone number.
Defaults to 520@-19,620@-19;10(*/0/1+2).
Busy Tone Played when a 486 RSC is received for an outbound call.
Defaults to 480@-19,620@-19;10(.5/.5/1+2).
Reorder Tone Played when an outbound call has failed or after the far end hangs up during an established
call. Reorder Tone is played automatically when <Dial Tone> or any of its alternatives
times out.
Defaults to 480@-19,620@-19;10(.25/.25/1+2).
Off Hook Warning Tone Played when the caller has not properly placed the handset on the cradle. Off Hook
Warning Tone is played when Reorder Tone times out.
Defaults to 480@10,620@0;10(.125/.125/1+2).
Ring Back Tone Played during an outbound call when the far end is ringing.
Defaults to 440@-19,480@-19;*(2/4/1+2).
Call Waiting Tone Played when a call is waiting. Defaults to 440@-10;30(.3/9.7/1)