Instruction Manual
Table Of Contents
- Preface
- Introducing Linksys IP Phones
- Getting Started
- Managing Linksys IP Phones
- Using the 900 Series LCD Display
- Localization
- Changing the Display Background (SPA942/962)
- Using the SPA932 (Sidecar) with the SPA962
- Configuring the Web Service
- RSS Newsfeeds (SPA962)
- Call Appearances and Extensions
- Line Key LEDs
- Using Call Features
- Selecting the Audio I/O Device and Line
- Making Calls
- Answering and Ending Calls
- Hold and Resume
- Call Waiting
- Speed Dialing
- Three-Way Conferencing
- Attended Call Transfer
- Blind Call Transfer
- Call Back
- Message Waiting Indication (MWI)
- Accessing Voicemail
- Muting Calls
- Shared Call Appearances
- Personal Directory
- Caller and Called Name Matching
- Dialing Assistance
- Supplementary Services
- Call Logs
- Audio Volume Adjustment
- Managing Ring Tones
- Configuring a Dial Plan
- System Administration
- Troubleshooting FAQ
- SPA900 Series LCD Command Reference
- Entering Names and Numbers into the Directory
- Entering Directory Names, Numbers and Ring Default
- 2 Speed Dial
- 3 Call History
- 4 Ring Tone
- 5 Preferences
- 6 Call Forward
- 7 Time/Date
- 8 Voice Mail
- 9 Network
- 9.1 DCHP
- 9.2 Current IP Address
- 9.3 Host Name
- 9.4 Domain
- 9.5 Current NetMask
- 9.6 Current Gateway
- 9.7 Enable Web Server
- 9.8 Non DHCP IP Address
- 9.9 Non DHCP Subnet Mask
- 9.10 Non DHCP Default Route
- 9.11 Non DHCP DNS 1
- 9.12 Non DHCP DNS 2
- 9.13 Non DHCP NTP Server 1
- 9.14 Non DHCP NTP Server 2
- 9.15 Multicast Address
- 9.16 Enable VLAN
- 9.17 VLAN ID
- 9.18 CDP
- 10 Product Info
- 11 Status
- 12 Reboot
- 13 Restart
- 14 Factory Reset
- 15 Custom Reset
- 16 Set Password
- 17 Set LCD Contrast
- 18 CallPark Status
- 19 Language (SPA922, 942, and 962)
- 20 GUI Properties (SPA962)
- 21 Web Service (SPA962)
- Linksys IP Phone Field Reference
- Acronyms
- Glossary

5-12
Linksys IP Phone Administrator Guide
Firmware Version 5.1
Chapter 5 Linksys IP Phone Field Reference
SIP Tab
Reg Retry Random Delay Random delay range (in seconds) to add to <Register Retry Intvl> when retrying
REGISTER after a failure. This feature was added in Release 5.1.
Defaults to blank, which disables this feature.
Reg Retry Long Random Delay Random delay range (in seconds) to add to <Register Retry Long Intvl> when retrying
REGSITER after a failure. This feature was added in Release 5.1.
Defaults to blank, which disables this feature.
Reg Retry Intvl Cap The maximum value to cap the exponential back-off retry delay (which starts at <Register
Retry Intvl> and doubles on every REGISTER retry after a failure). In other words, the
retry interval is always at <Register Retry Intvl> seconds after a failure. If this feature is
enabled, <Reg Retry Random Delay> is added on top of the exponential back-off adjusted
delay value. This feature was added in Release 5.1.
Defaults to blank, which disables the exponential back-off feature.
Sub Min Expires This value sets the lower limit of the REGISTER expires value returned from the Proxy
server.
Sub Max Expires This value sets the upper limit of the REGISTER min-expires value returned from the
Proxy server in the Min-Expires header. Defaults to 7200.
Sub Retry Intvl This value (in seconds) determines the retry interval when the last Subscribe request fails.
Defaults to 10.
Field Description