Instruction Manual
Table Of Contents
- Preface
- Introducing Linksys IP Phones
- Getting Started
- Managing Linksys IP Phones
- Using the 900 Series LCD Display
- Localization
- Changing the Display Background (SPA942/962)
- Using the SPA932 (Sidecar) with the SPA962
- Configuring the Web Service
- RSS Newsfeeds (SPA962)
- Call Appearances and Extensions
- Line Key LEDs
- Using Call Features
- Selecting the Audio I/O Device and Line
- Making Calls
- Answering and Ending Calls
- Hold and Resume
- Call Waiting
- Speed Dialing
- Three-Way Conferencing
- Attended Call Transfer
- Blind Call Transfer
- Call Back
- Message Waiting Indication (MWI)
- Accessing Voicemail
- Muting Calls
- Shared Call Appearances
- Personal Directory
- Caller and Called Name Matching
- Dialing Assistance
- Supplementary Services
- Call Logs
- Audio Volume Adjustment
- Managing Ring Tones
- Configuring a Dial Plan
- System Administration
- Troubleshooting FAQ
- SPA900 Series LCD Command Reference
- Entering Names and Numbers into the Directory
- Entering Directory Names, Numbers and Ring Default
- 2 Speed Dial
- 3 Call History
- 4 Ring Tone
- 5 Preferences
- 6 Call Forward
- 7 Time/Date
- 8 Voice Mail
- 9 Network
- 9.1 DCHP
- 9.2 Current IP Address
- 9.3 Host Name
- 9.4 Domain
- 9.5 Current NetMask
- 9.6 Current Gateway
- 9.7 Enable Web Server
- 9.8 Non DHCP IP Address
- 9.9 Non DHCP Subnet Mask
- 9.10 Non DHCP Default Route
- 9.11 Non DHCP DNS 1
- 9.12 Non DHCP DNS 2
- 9.13 Non DHCP NTP Server 1
- 9.14 Non DHCP NTP Server 2
- 9.15 Multicast Address
- 9.16 Enable VLAN
- 9.17 VLAN ID
- 9.18 CDP
- 10 Product Info
- 11 Status
- 12 Reboot
- 13 Restart
- 14 Factory Reset
- 15 Custom Reset
- 16 Set Password
- 17 Set LCD Contrast
- 18 CallPark Status
- 19 Language (SPA922, 942, and 962)
- 20 GUI Properties (SPA962)
- 21 Web Service (SPA962)
- Linksys IP Phone Field Reference
- Acronyms
- Glossary
5-8
Linksys IP Phone Administrator Guide
Firmware Version 5.1
Chapter 5 Linksys IP Phone Field Reference
System Tab
VLAN Settings
Note None of the following parameters apply to the SPA901.
Secondary DNS DNS server used by Linksys IP phone in addition to DHCP supplied DNS servers if
DHCP is enabled; when DHCP is disabled, this is the secondary DNS server.
Defaults to 0.0.0.0.
DNS Server Order
(Not applicable to SPA901)
Specifies the method for selecting the DNS server. The options are Manual,
Manual/DHCP, and DHCP/Manual.
DNS Query Mode Do parallel or sequential DNS Query. With parallel DNS query mode, the Linksys IP
phone sends the same request to all the DNS servers at the same time when doing a DNS
lookup, the first incoming reply is accepted by the Linksys IP phone.
Defaults to parallel.
Syslog Server Specify the syslog server name and port. This feature specifies the server for logging
Linksys IP phone system information and critical events. If both Debug Server and Syslog
Server are specified, Syslog messages are also logged to the Debug Server.
Debug Server The debug server name and port. This feature specifies the server for logging Linksys IP
phone debug information. The level of detailed output depends on the debug level
parameter setting.
Debug Level The debug level from 0-3. The higher the level, the more debug information is generated.
Zero (0) means no debug information is generated. To log SIP messages, you must set the
Debug Level to at least 2.
Defaults to 0.
Primary NTP Server
(Not applicable to SPA901)
IP address or name of primary NTP server.
Secondary NTP Server
(Not applicable to SPA901)
IP address or name of secondary NTP server.
Field Description
Enable VLAN Enable this parameter if the switch to which the Linksys IP phone is connected uses
VLAN tagging.
VLAN ID Enter the VLAN tag for the VLAN to which the Linksys IP phone is assigned. This should
be the same VLAN to which the SPA9000 is assigned.
Enable CDP Enables or disables Cisco Discovery Protocol (CDP.
Defaults to Yes.
Field Description