Switch User Manual
Table Of Contents
- Chapter 1: Introduction
- Chapter 2: Product Overview
- Chapter 3: Installation
- Chapter 4: Configuration Using the Console Interface
- Chapter 5: Advanced Configuration
- Overview
- Accessing the Web-based Utility
- Setup > Summary
- Setup > Network Settings
- Setup > Time
- Port Management > Port Settings
- Port Management > Link Aggregation
- Port Management > LACP
- Port Management > PoE Power Settings
- VLAN Management > Create VLAN
- VLAN Management > Port Settings
- VLAN Management > Ports to VLAN
- VLAN Management > VLAN to Ports
- VLAN Management > GVRP
- Statistics > RMON Statistics
- Statistics > RMON History
- Statistics > RMON Alarms
- Statistics > RMON Events
- Statistics > Port Utilization
- Statistics > 802.1x Statistics
- Statistics > GVRP Statistics
- ACL > IP based ACL
- ACL > MAC based ACL
- Security > ACL Binding
- Security > RADIUS
- Security > TACACS+
- Security > 802.1x Settings
- Security > Ports Security
- Security > Multiple Hosts
- Security > Storm Control
- QoS
- QoS > CoS Settings
- QoS > Queue Settings
- QoS > DSCP Settings
- QoS > Bandwidth
- QoS > Basic Mode
- QoS > Advanced Mode
- Spanning Tree
- Spanning Tree > STP Status
- Spanning Tree > Global STP
- Spanning Tree > STP Port Settings
- Spanning Tree > RSTP Port Settings
- Spanning Tree > MSTP Properties
- Spanning Tree > MSTP Instance Settings
- Spanning Tree > MSTP Interface Settings
- Multicast > IGMP Snooping
- Multicast > Bridge Multicast
- Multicast > Bridge Multicast Forward All
- SNMP > Global Parameters
- SNMP > Views
- SNMP > Group Profile
- SNMP > Group Membership
- SNMP > Communities
- SNMP > Notification Filter
- SNMP > Notification Recipient
- Admin > User Authentication
- Admin > Static Address
- Admin > Dynamic Address
- Admin > Logging
- Admin > Port Mirroring
- Admin > Cable Test
- Admin > Save Configuration
- Admin > Firmware Upgrade
- Admin > Reboot
- Admin > Factory Defaults
- Admin > Server Logs
- Admin > Memory Logs
- Admin > Flash Logs
- Appendix A: About Gigabit Ethernet and Fiber Optic Cabling
- Appendix B: Introduction
- Appendix C: Glossary
- Appendix D: Specifications
- Appendix E: Warranty Information
- Appendix F: Regulatory Information
- Appendix G: Contact Information
Chapter 5
Advanced Configuration
38
8-Port 10/100 Ethernet Switch with Webview
Basic • Enables QoS on the interface.
Advanced • Enables Advanced mode QoS on the
interface.
Class of Service Specifies the CoS priority tag values,
where zero is the lowest and 7 is the highest.
Queue Defines the traffic forwarding queue to which the
CoS priority is mapped. Four traffic priority queues are
supported.
The Restore Defaults button restores the device factory
defaults for mapping CoS values to a forwarding queue.
CoS Default
Interface Interface to which the CoS configuration
applies.
Default CoS Determines the default CoS value for
incoming packets for which a VLAN tag is not defined. The
possible field values are 0-7. The default CoS is 0.
Restore Defaults Restores the device factory defaults for
mapping CoS values to a forwarding queue.
LAG LAG to which the CoS configuration applies.
QoS > Queue Settings
QoS > Queue Settings
The Queue Setting screen contains fields for defining the
QoS queue forwarding types.
Strict Priority Indicates that traffic scheduling for the
selected queue is based strictly on the queue priority.
WRR Indicates that traffic scheduling for the selected
queue is based strictly on the WRR.
Queue Displays the queue for which the queue settings
are displayed. The possible field range is 1 - 4.
WRR Weight Displays the WRR weights to queues.
% of WRR Bandwidth Displays the amount of bandwidth
assigned to the queue. These values are fixed and are not
user defined.
QoS > DSCP Settings
QoS > DSCP Settings
The DSCP Settings screen enables mapping DSCP values to
specific queues.
The DSCP Settings screen contains the following fields:
DSCP Indicates the Differentiated Services Code Point
value in the incoming packet.
Queue Maps the DSCP value to the selected queue.
QoS > Bandwidth
QoS > Bandwidth
The Bandwidth screen allows network managers to define
the bandwidth settings for a specified egress interface.