Switch User Manual
Table Of Contents
- Chapter 1: Introduction
- Chapter 2: Product Overview
- Chapter 3: Installation
- Chapter 4: Configuration Using the Console Interface
- Chapter 5: Advanced Configuration
- Overview
- Accessing the Web-based Utility
- Setup > Summary
- Setup > Network Settings
- Setup > Time
- Port Management > Port Settings
- Port Management > Link Aggregation
- Port Management > LACP
- Port Management > PoE Power Settings
- VLAN Management > Create VLAN
- VLAN Management > Port Settings
- VLAN Management > Ports to VLAN
- VLAN Management > VLAN to Ports
- VLAN Management > GVRP
- Statistics > RMON Statistics
- Statistics > RMON History
- Statistics > RMON Alarms
- Statistics > RMON Events
- Statistics > Port Utilization
- Statistics > 802.1x Statistics
- Statistics > GVRP Statistics
- ACL > IP based ACL
- ACL > MAC based ACL
- Security > ACL Binding
- Security > RADIUS
- Security > TACACS+
- Security > 802.1x Settings
- Security > Ports Security
- Security > Multiple Hosts
- Security > Storm Control
- QoS
- QoS > CoS Settings
- QoS > Queue Settings
- QoS > DSCP Settings
- QoS > Bandwidth
- QoS > Basic Mode
- QoS > Advanced Mode
- Spanning Tree
- Spanning Tree > STP Status
- Spanning Tree > Global STP
- Spanning Tree > STP Port Settings
- Spanning Tree > RSTP Port Settings
- Spanning Tree > MSTP Properties
- Spanning Tree > MSTP Instance Settings
- Spanning Tree > MSTP Interface Settings
- Multicast > IGMP Snooping
- Multicast > Bridge Multicast
- Multicast > Bridge Multicast Forward All
- SNMP > Global Parameters
- SNMP > Views
- SNMP > Group Profile
- SNMP > Group Membership
- SNMP > Communities
- SNMP > Notification Filter
- SNMP > Notification Recipient
- Admin > User Authentication
- Admin > Static Address
- Admin > Dynamic Address
- Admin > Logging
- Admin > Port Mirroring
- Admin > Cable Test
- Admin > Save Configuration
- Admin > Firmware Upgrade
- Admin > Reboot
- Admin > Factory Defaults
- Admin > Server Logs
- Admin > Memory Logs
- Admin > Flash Logs
- Appendix A: About Gigabit Ethernet and Fiber Optic Cabling
- Appendix B: Introduction
- Appendix C: Glossary
- Appendix D: Specifications
- Appendix E: Warranty Information
- Appendix F: Regulatory Information
- Appendix G: Contact Information
9
Configuration Using the Console Interface
8-Port 10/100 Ethernet Switch with Webview
Chapter 4
Chapter 4:
Configuration Using the
Console Interface
Overview
The Switch features a menu-driven console interface for
basic configuration of the Switch and management of your
network. The Switch can be configured using CLI through
the console interface or through a telnet connection.
This chapter describes console interface configuration.
Configuration can also be performed through the web
utility, which is covered in the next chapter.
Configuring the HyperTerminal Application
Click the 1. Start button.
Select 2. Programs > Accessories > Communications >
HyperTerminal.
Start > Programs > Accessories > Communications > HyperTerminal
Enter a name for this connection. In the example, the 3.
name of the connection is SRW208. Select an icon for
the application, then click OK.
HyperTerminal Connection Description Screen
Select a port to communicate with the switch. Select 4.
COM1, COM2, or TCP/IP.
HyperTerminal Connect To Screen
Set the serial port settings as follows, then click 5. OK.
Bits per Second: 38400
Databits: 8
Parity: None
Stop bits: 1
Flow control: None
HyperTerminal Properties Screen
Connecting to the Switch through a Telnet
Session
Open a command line editor and enter 1. telnet
192.168.1.254. Then, press the Enter key.
The 2. Login screen will now appear. The first time you
open the CLI interface, select Edit and hit Enter. Enter
admin in the User Name field. Leave the Password field
blank.