® A Division of Cisco Systems, Inc. Wired Broadband Router User Guide Model No.
Wired Broadband Router Copyright and Trademarks Specifications are subject to change without notice. Linksys is a registered trademark or trademark of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Copyright © 2005 Cisco Systems, Inc. All rights reserved. Other brands and product names are trademarks or registered trademarks of their respective holders.
Wired Broadband Router Table of Contents Chapter 1: Introduction 1 Welcome What’s in this Guide? 1 2 Chapter 2: Networking Basics 4 An Introduction to Local Area Networks The Use of IP Addresses 4 4 Chapter 3: Getting to Know the Router 6 The Back Panel The Front Panel Chapter 4: Connecting the Router Overview Connecting the Router to Your Broadband Modem Chapter 5: Configuring the Router Overview How to Access the Web-based Utility The Setup Tab - Basic Setup The Setup Tab - DDNS The Setup Tab
Wired Broadband Router The Status Tab - Router The Status Tab - Local Network Appendix A: Troubleshooting Common Problems and Solutions Frequently Asked Questions 34 35 36 36 45 Appendix B: Finding the MAC Address and IP Address for Your Ethernet Adapter 49 Windows 98 or Me Instructions Windows 2000 or XP Instructions For the Router’s Web-based Utility Appendix C: Windows Help Appendix D: Glossary Appendix E: Specifications Appendix F: Warranty Information Appendix G: Regulatory Information Appendix H
Wired Broadband Router List of Figures Figure 3-1: Back Panel Figure 3-2: Front Panel Figure 4-1: Connect the Broadband Modem Figure 4-2: Connect a PC Figure 4-3: Connect the Power Figure 5-1: Router’s IP Address Figure 5-2: Router Login Figure 5-3: Setup Tab - Basic Setup(Automatic Configuration - DHCP) Figure 5-4: Static IP Figure 5-5: PPPoE Figure 5-6: PPTP Figure 5-7: Setup Tab - DDNS (DynDNS.org) Figure 5-8: Setup Tab - DDNS (TZO.
Wired Broadband Router Figure 5-24: Ping Test Figure 5-25: Traceroute Test Figure 5-26: Administration Tab - Factory Defaults Figure 5-27: Administration Tab - Firmware Upgrade Figure 5-28: Administration Tab - Backup and Restore Figure 5-29: Administration Tab - Reboot Figure 5-30: Status Tab - Router Figure 5-31: Status Tab - Local Network Figure 5-32: DHCP Clients Table Figure B-1: IP Configuration Screen Figure B-2: MAC Address/Adapter Address Figure B-3: MAC Address/Physical Address Figure B-4: Access
Wired Broadband Router Chapter 1: Introduction Welcome Thank you for choosing the Wired Broadband Router. This Router will allow your computers to share a high-speed Internet connection as well as resources, including files and printers. How does the Router do all of this? By connecting your computers and peripherals to the Router and connecting the Router to your cable or DSL modem, the Router can direct and control communications for your network.
Wired Broadband Router What’s in this Guide? This user guide covers the basic steps for setting up a network with a router. After going through “Chapter 3: Getting to Know the Router,” most users will only need to use the following chapters: • Chapter 4: Connecting the Router This chapter instructs you on how to connect the Router to your cable or DSL modem and PCs.
Wired Broadband Router • Appendix G: Regulatory Information This appendix supplies the regulatory information regarding the Router. • Appendix H: Contact Information This appendix provides contact information for a variety of Linksys resources, including Technical Support.
Wired Broadband Router Chapter 2: Networking Basics An Introduction to Local Area Networks Simply put, a router is a network device that connects two networks together. The Router connects your local area network (LAN), or the group of PCs in your home or office, to the Internet. The Router processes and regulates the data that travels between these two networks. The Router’s Network Address Translation (NAT) technology protects your network of PCs so users on the Internet cannot “see” your PCs.
Wired Broadband Router A DHCP server can either be a designated PC on the network or another network device, such as the Router. By default, the Router’s Internet Connection Type is Obtain an IP automatically (DHCP). The PC or network device obtaining an IP address is called the DHCP client. DHCP frees you from having to assign IP addresses manually every time a new user is added to your network.
Wired Broadband Router Chapter 3: Getting to Know the Router The Back Panel The Router’s ports and the Reset button are located on the back panel of the Router. Figure 3-1: Back Panel Internet This Internet port connects to your cable or DSL modem. Ethernet 1-4 These four Ethernet ports connect to network devices, such as PCs, print servers, or additional switches. Reset Button There are two ways to reset the Router to its factory default settings.
Wired Broadband Router The Front Panel The Router’s LEDs, which inform you about network activities, are located on the front panel. Figure 3-2: Front Panel Power Green. The Power LED lights up when the Router is powered on. If the LED is flashing, the Router is booting up or running a system self-test. Ethernet 1-4 Green. The Ethernet LED serves two purposes. If the LED is solidly lit, the Router is connected to a device through the corresponding port (Ethernet 1, 2, 3, or 4).
Wired Broadband Router Chapter 4: Connecting the Router Overview This chapter provides instructions to connect the Router to your Broadband Modem. Connecting the Router to Your Broadband Modem 1. Make sure that all of your hardware is powered off, including the Router, PCs, and broadband modem. 2. Connect your broadband modem’s Ethernet cable to the Router’s Internet port. 3. Connect one end of an Ethernet network cable to one of the numbered ports on the back of the Router.
Wired Broadband Router Chapter 5: Configuring the Router Overview Linksys recommends using the Setup CD-ROM for first-time installation of the Router. If you do not wish to run the Setup Wizard on the Setup CD-ROM, then you can use the Web-based Utility to configure the Router. For advanced users, you may configure the Router’s advanced settings through the Web-based Utility. This chapter will describe each web page on the Utility and each page’s key functions.
Wired Broadband Router Access Restrictions Internet Access. This screen allows you to permit or block specific kinds of Internet usage and traffic. Applications & Gaming • Port Range Forward. Set up public services or other specialized Internet applications on your network. • Port Trigger. To set up triggered ranges and forwarded ranges for Internet applications, click this tab. • UPnP Forward. Use this screen to alter UPnP forwarding settings. • DMZ.
Wired Broadband Router How to Access the Web-based Utility To access the Web-based Utility of the Router, launch Internet Explorer or Netscape Navigator, and enter the Router’s default IP address, 192.168.15.1, in the Address field. Press the Enter key. Figure 5-1: Router’s IP Address A screen will appear asking you for your User Name and Password. Leave the User Name field blank, and enter admin in the User Name and Password fields. Then click the OK button. Make the necessary changes through the Utility.
Wired Broadband Router Static IP If you are required to use a permanent IP address, then select Static IP. Internet IP Address. This is the IP address that the Router has, when seen from the Internet. Your ISP will provide you with the IP Address you need to specify here. Subnet Mask. This is the Router’s Subnet Mask, as seen by external users on the Internet (including your ISP). Your ISP will provide you with the Subnet Mask. Default Gateway. Your ISP will provide you with the Default Gateway Address.
Wired Broadband Router PPTP Point-to-Point Tunneling Protocol (PPTP) is a service that applies to connections in Europe and Israel only. Internet IP Address. This is the IP address that the Router has, when seen from the Internet. Your ISP will provide you with the IP Address you need to specify here. Subnet Mask. This is the Router’s Subnet Mask, as seen by external users on the Internet (including your ISP). Your ISP will provide you with the Subnet Mask. Gateway.
Wired Broadband Router desired. It is recommended that you leave this value in the 1200 to 1500 range. For most DSL users, it is recommended to use the value 1492. By default, MTU is set at 1500 when disabled. Internet Port Speed. You can specify the transmission speed of the Router’s Internet port if your broadband modem requires a specific speed setting. In most cases you should keep the default setting, Auto.
Wired Broadband Router Static DNS 1-2. The Domain Name System (DNS) is how the Internet translates domain or website names into Internet addresses or URLs. Your ISP will provide you with at least one DNS Server IP Address. You can enter up to two DNS Server IP Addresses here. The Router will use these for quicker access to functioning DNS servers. WINS. The Windows Internet Naming Service (WINS) converts NetBIOS names to IP addresses. If you use a WINS server, enter that server’s IP address here.
Wired Broadband Router The Setup Tab - DDNS The Router offers a Dynamic Domain Name System (DDNS) feature. DDNS lets you assign a fixed host and domain name to a dynamic Internet IP address. It is useful when you are hosting your own website, FTP server, or other server behind the Router. Before you can use this feature, you need to sign up for DDNS service at one of two DDNS service providers, DynDNS.org or TZO.com. If you do not want to use this feature, keep the default setting, Disable.
Wired Broadband Router The Setup Tab - MAC Address Clone A MAC address is a 12-digit code assigned to a unique piece of hardware for identification, like a social security number. Some ISPs will require you to register a MAC address in order to access the Internet. If you do not wish to re-register the MAC address with your ISP, you may assign the MAC address currently registered with your ISP to the Router using the MAC Address Clone feature. MAC Clone To use MAC address cloning, select Enable.
Wired Broadband Router The Security Tab - Firewall When you click the Security tab, you will see the Firewall screen. The Router’s firewall enhances the security of your network. You can also enable a variety of filters to further protect your network and block anonymous Internet requests. Firewall The firewall uses Stateful Packet Inspection (SPI) to check the incoming data transmissions before allowing them to enter your network.
Wired Broadband Router The Security Tab - VPN The VPN screen allows you to allow VPN tunnels using IPSec, PPTP, or L2TP protocols to pass through the Router. VPN Passthrough IPSec Passthrough. IPSec (Internet Protocol Security) is a suite of protocols used to implement secure exchange of packets at the IP layer. To allow IPSec Passthrough, click the Enable button. To disable IPSec Passthrough, click the Disable button. PPTP Passthrough.
Wired Broadband Router The Access Restrictions Tab - Internet Access The Internet Access screen allows you to block or allow specific kinds of Internet usage and traffic, such as Internet access, designated services, and websites during specific days and times. Internet Access Internet Access Policy. Access can be managed by a policy. Use the settings on this screen to establish an access policy (after the Save Settings button is clicked).
Wired Broadband Router 4. Click the Edit List of PCs button to select which PCs will be affected by the policy. The List of PCs screen will appear. You can select a PC by MAC Address or IP Address. You can also enter a range of IP Addresses if you want this policy to affect a group of PCs. After making your changes, click the Save Settings button to apply your changes or Cancel Changes to cancel your changes. Click the Close button to return to the Internet Access screen. 5.
Wired Broadband Router The Applications & Gaming Tab - Port Range Forward When you click the Applications & Gaming tab, you will see the Port Range Forward screen. Port range forwarding sets up public services on your network, such as web servers, ftp servers, e-mail servers, or other specialized Internet applications. (Specialized Internet applications are any applications that use Internet access to perform functions such as videoconferencing or online gaming.
Wired Broadband Router The Applications & Gaming Tab - Port Trigger The Port Trigger screen allows the Router to watch outgoing data for specific port numbers. The IP address of the computer that sends the matching data is remembered by the Router, so that when the requested data returns through the Router, the data is pulled back to the proper computer by way of IP address and port mapping rules. Port Trigger Application. Enter the application name of the trigger. Triggered Range Protocol.
Wired Broadband Router The Applications & Gaming Tab - UPnP Forward The UPnP Forward screen displays preset application settings as well as options to customize port services for other applications. UPnP Forward Application. Ten applications are preset. For custom applications, enter the name of your application in one of the available fields. The preset applications are among the most widely used Internet applications. They include the following: FTP (File Transfer Protocol).
Wired Broadband Router NNTP (Network News Transfer Protocol). The protocol used to connect to Usenet groups on the Internet. Usenet newsreaders support the NNTP protocol. SNMP (Simple Network Management Protocol). A widely used network monitoring and control protocol. Data is passed from SNMP agents, which are hardware and/or software processes reporting activity in each network device (hub, router, bridge, etc.) to the workstation console used to oversee the network.
Wired Broadband Router The Applications & Gaming Tab - DMZ The DMZ screen allows one local user to be exposed to the Internet for use of a special-purpose service such as Internet gaming and videoconferencing. DMZ hosting forwards all the ports at the same time to one PC. Port Range Forwarding is more secure because it only opens the ports you want to have opened, while DMZ hosting opens all the ports of one computer, exposing the computer to the Internet.
Wired Broadband Router The Administration Tab - Management When you click the Administration tab, you will see the Management screen. This screen allows you to change the Router’s access settings as well as configure the SNMP (Simple Network Management Protocol) and UPnP (Universal Plug and Play) features. Router Password Local Router Access To ensure the Router’s security, you will be asked for your password when you access the Router’s Web-based Utility. The default password is admin. Router Password.
Wired Broadband Router Set Community. Enter the password that allows read/write access to the Router’s SNMP information.The default name is private. A name must be entered in this field. SNMP Trap Community. Enter the password required by the remote host computer that will receive trap messages or notices sent by the Router. SNMP Trap Destination. Enter the IP address of the remote host computer that will receive the trap messages. UPnP UPnP.
Wired Broadband Router The Administration Tab - Log The Log screen provides you with a log of all incoming and outgoing URLs or IP addresses for your Internet connection. Log Log. To keep activity logs, select the Enable radio button. With logging enabled, you can choose to view temporary logs or keep a permanent record using the Logviewer software. Click the Disable button to disable this function. Figure 5-20: Administration Tab - Log Log Viewer IP Address.
Wired Broadband Router The Administration Tab - Diagnostics The diagnostic tests (Ping and Traceroute) allow you to check the connections of your network components. Ping Test. The Ping test will check the status of a connection. Click the Ping button to open the Ping Test screen. Enter the IP address or domain name of the PC whose connection you wish to test and how many times you wish to test it, 5, 10, or unlimited. Then, click the Ping button. To stop the test, click the Stop button.
Wired Broadband Router The Administration Tab - Factory Defaults The Factory Defaults screen allows you to restore the Router’s configuration to its factory default settings. Factory Defaults Restore Factory Defaults. To clear all of the Router’s settings and reset them to its factory defaults, click the Yes radio button.
Wired Broadband Router The Administration Tab - Firmware Upgrade The Firmware Upgrade screen allows you to upgrade the Router’s firmware. Do not upgrade the firmware unless you are experiencing problems with the Router or the new firmware has a feature you want to use. Before upgrading the firmware, download the Router’s firmware upgrade file from the Linksys website, www.linksys.com. Then extract the file. Upgrade Firmware Please select a file to upgrade.
Wired Broadband Router The Administration Tab - Backup and Restore The Backup and Restore screen allows you to back up and restore the Router’s configuration. Backup and Restore Please select a file to restore. In the field provided, enter the name of the configuration file you want to restore, or click the Browse button to find this file. Backup. To create a backup configuration file, click the Backup button, and follow the on-screen instructions. Restore.
Wired Broadband Router The Status Tab - Router The Router screen displays information about the Router and its current settings. Router Information Current Firmware Version. This shows the version and date of the firmware that is currently installed. Previous Firmware Version. This shows the version and date of the firmware that was previously installed. Current Time. The current time and date are displayed here. MAC Address. The MAC Address of the Router’s Internet interface is displayed here.
Wired Broadband Router The Status Tab - Local Network The Local Network screen displays information about the local network. Local Network MAC Address. The MAC Address of the Router’s LAN (local area network) interface is displayed here. IP Address. The Router’s local IP Address is shown here. Subnet Mask. The Router’s Subnet Mask is shown here. DHCP Server. The status of the DHCP server is displayed here. Start IP Address. This is the starting IP address of the range assigned by the Router.
Wired Broadband Router Appendix A: Troubleshooting This appendix provides solutions to problems that may occur during the installation and operation of the Router. Read the description below to solve your problems. If you can't find an answer here, check the Linksys website at www.linksys.com. Common Problems and Solutions 1. I’m trying to access the Router’s Web-based Utility, but I do not see the login screen. Instead, I see a screen saying, “404 Forbidden.
Wired Broadband Router E. Click the DNS tab, and make sure the DNS Enabled option is selected. Enter the Host and Domain names (e.g., John for Host and home for Domain). Enter the DNS entry provided by your ISP. If your ISP has not provided the DNS IP address, contact your ISP to get that information or go to its website for the information. F. Click the OK button in the TCP/IP properties window, and click Close or the OK button for the Network window. G. Restart the computer when asked.
Wired Broadband Router E. Enter a unique IP address that is not used by any other computer on the network connected to the Router. You can only use an IP address in the ranges 192.168.15.2 to 192.168.15.99 and 192.168.15.151 to 192.168.15.254. F. Enter the Subnet Mask, 255.255.255.0. G. Enter the Default Gateway, 192.168.15.1 (Router’s default IP address). H.
Wired Broadband Router 3. Right-click the Local Area Connection that is associated with the Ethernet adapter you are using, and select the Properties option. 4. In the This connection uses the following items box, highlight Internet Protocol (TCP/IP), and click the Properties button. Make sure that Obtain an IP address automatically and Obtain DNS server address automatically are selected. B. Open a command prompt. • For Windows 98 and Millennium, click Start and Run. In the Open field, type command.
Wired Broadband Router D. Make sure you use the right cable. Check to see if the Internet LED is solidly lit. E. Make sure the cable connecting from your cable or DSL modem is connected to the Router’s Internet port. Verify that the Status page of the Router’s Web-based Utility shows a valid IP address from your ISP. F. Turn off the computer, Router, and cable/DSL modem. Wait 30 seconds, and then turn on the Router, cable/DSL modem, and computer.
Wired Broadband Router 7. I need to set up a server behind my Router. To use a server like a web, ftp, or mail server, you need to know the respective port numbers they are using. For example, port 80 (HTTP) is used for web; port 21 (FTP) is used for FTP, and port 25 (SMTP outgoing) and port 110 (POP3 incoming) are used for the mail server. You can get more information by viewing the documentation provided with the server you installed.
Wired Broadband Router A. Access the Router’s Web-based Utility by going to http://192.168.15.1 or the IP address of the Router. Go to the Applications & Gaming => Port Range Forward tab. B. Enter any name you want to use for the Application. C. Enter the port range of the service you are using. For example, if you have a web server, you would enter the range 80 to 80. D. Select the protocol you will be using, TCP or UDP, or select Both. E.
Wired Broadband Router D. Enter the Ethernet adapter’s IP address of the computer you want exposed to the Internet. This will bypass the NAT security for that computer. Please refer to “Appendix C: Finding the MAC Address and IP Address for Your Ethernet Adapter” for details on getting an IP address. Once completed with the configuration, click the Save Settings button. 10. I forgot my password, or the password prompt always appears when saving settings to the Router.
Wired Broadband Router 13. My DSL service’s PPPoE is always disconnecting. PPPoE is not actually a dedicated or always-on connection. The DSL ISP can disconnect the service after a period of inactivity, just like a normal phone dial-up connection to the Internet. There is a setup option to “keep alive” the connection. This may not always work, so you may need to re-establish connection periodically. A. To connect to the Router, go to the web browser, and enter http://192.168.15.
Wired Broadband Router B. C. D. E. Enter the password, if asked. (The default password is admin.) Click the Applications & Gaming => Port Trigger tab. Enter any name you want to use for the Application Name. Enter the Start and End Ports of the Triggered Port Range. Check with your Internet application provider for more information on which outgoing port services it is using. F. Enter the Start and End Ports of the Forwarded Port Range.
Wired Broadband Router Does the Router support IPX or AppleTalk? No. TCP/IP is the only protocol standard for the Internet and has become the global standard for communications. IPX, a NetWare communications protocol used only to route messages from one node to another, and AppleTalk, a communications protocol used on Apple and Macintosh networks, can be used for LAN to LAN connections, but those protocols cannot connect from the Internet to the LAN.
Wired Broadband Router the same time, even if on the same LAN (not a problem with 1.0.1.3). As far as hosting games, the HL server does not need to be in the DMZ. Just forward port 27015 to the local IP address of the server computer. How can I block corrupted FTP downloads? If you are experiencing corrupted files when you download a file with your FTP client, try using another FTP program. The web page hangs; downloads are corrupt, or nothing but junk characters are being displayed on the screen.
Wired Broadband Router Does the Router pass PPTP packets or actively route PPTP sessions? The Router allows PPTP packets to pass through. Is the Router cross-platform compatible? Any platform that supports Ethernet and TCP/IP is compatible with the Router. How many ports can be simultaneously forwarded? Theoretically, the Router can establish 520 sessions at the same time, but you can only forward 10 ranges of ports.
Wired Broadband Router AppendixB:FindingtheMACAddressandIPAddressforYour Ethernet Adapter This section describes how to find the MAC address for your computer’s Ethernet adapter so you can use the MAC filtering and/or MAC address cloning feature of the Router. You can also find the IP address of your computer’s Ethernet adapter. This IP address is used for the Router’s filtering, forwarding, and/or DMZ features.
Wired Broadband Router 3. Write down the Physical Address as shown on your computer screen; it is the MAC address for your Ethernet adapter. This appears as a series of numbers and letters. The MAC address/Physical Address is what you will use for MAC address cloning or MAC filtering. NOTE: The MAC address is also called the Physical Address. The example shows the Ethernet adapter’s IP address as 192.168.1.100. Your computer may show something different.
Wired Broadband Router Appendix C: Windows Help Almost all networking products require Microsoft Windows. Windows is the most used operating system in the world and comes with many features that help make networking easier. These features can be accessed through Windows Help and are described in this appendix. TCP/IP Before a computer can communicate with the Router, TCP/IP must be enabled. TCP/IP is a set of instructions, or protocol, all PCs follow to communicate over a wired or wireless network.
Wired Broadband Router Appendix D: Glossary Adapter - A device that adds network functionality to your PC. Backbone - The part of a network that connects most of the systems and networks together, and handles the most data. Bandwidth - The transmission capacity of a given device or network. Beacon Interval - Data transmitted on your wireless network that keeps the network synchronized. Bit - A binary digit. Boot - To start a device and cause it to start executing instructions.
Wired Broadband Router Default Gateway - A device that forwards Internet traffic from your local area network. DHCP (Dynamic Host Configuration Protocol) - A networking protocol that allows administrators to assign temporary IP addresses to network computers by “leasing” an IP address to a user for a limited amount of time, instead of assigning permanent IP addresses. DMZ (Demilitarized Zone) - Removes the Router's firewall protection from one PC, allowing it to be “seen” from the Internet.
Wired Broadband Router Half Duplex - Data transmission that can occur in two directions over a single line, but only one direction at a time. Hardware - The physical aspect of computers, telecommunications, and other information technology devices. HTTP (HyperText Transport Protocol) - The communications protocol used to connect to servers on the World Wide Web. IP (Internet Protocol) - A protocol used to send data over a network. IP Address - The address used to identify a computer or device on a network.
Wired Broadband Router Ping (Packet INternet Groper) - An Internet utility used to determine whether a particular IP address is online. POP3 (Post Office Protocol 3) - A standard mail server commonly used on the Internet. Port - The connection point on a computer or networking device used for plugging in cables or adapters. Power over Ethernet (PoE) - A technology enabling an Ethernet network cable to deliver both data and power.
Wired Broadband Router Switch - 1. A data switch that connects computing devices to host computers, allowing a large number of devices to share a limited number of ports. 2. A device for making, breaking, or changing the connections in an electrical circuit. TCP (Transmission Control Protocol) - A network protocol for transmitting data that requires acknowledgement from the recipient of data sent.
Wired Broadband Router Appendix E: Specifications Model RT41-BU Standards IEEE 802.3 (10BaseT), IEEE 802.3u (100BaseTX) Ports/Buttons One 10/100 RJ-45 Port for Broadband Modem, Four 10/100 RJ-45 Switched Ports, One Power Port, One Reset Button Cabling Type RJ-45 Ethernet Category 5 LEDs Power, Ethernet (1-4), Internet UPnP able/cert Able Network Protocols TCP/IP, NetBEUI, IPX/SPX Dimensions (W x H x D) 7.32" x 1.89" x 6.10" (186 mm x 48 mm x 155 mm) Unit Weight 13.33 oz. (0.
Wired Broadband Router Appendix F: Warranty Information LIMITED WARRANTY Linksys warrants to You that, for a period of one year (the “Warranty Period”), your Linksys Product will be substantially free of defects in materials and workmanship under normal use. Your exclusive remedy and Linksys' entire liability under this warranty will be for Linksys at its option to repair or replace the Product or refund Your purchase price less any rebates. This limited warranty extends only to the original purchaser.
Wired Broadband Router Appendix G: Regulatory Information FCC STATEMENT This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Wired Broadband Router User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste Electric and Electronic Equipment (WEEE) This document contains important information for users with regards to the proper disposal and recycling of Linksys products.
Wired Broadband Router Appendix G: Regulatory Information 61
Wired Broadband Router Appendix G: Regulatory Information 62
Wired Broadband Router Appendix G: Regulatory Information 63
Wired Broadband Router For more information, visit www.linksys.com.
Wired Broadband Router Appendix H: Contact Information Need to contact Linksys? Visit us online for information on the latest products and updates to your existing products at: http://www.linksys.com or ftp.linksys.
