User's Manual
Table Of Contents
- Product overview
- Setting Up: Basics
- How to create a home network
- Where to find more help
- How to set up your router
- How to improve your wireless connection speed
- How to test your Internet connection speed
- How to connect devices to your network
- How to set up parental controls
- How to set up guest access to your network
- How to change your router’s name and password
- Setting Up: Advanced
- How to open the browser-based utility
- How to manually set up your router
- How to set up the DHCP server on your router
- How to find your network on the Internet
- How to clone a MAC address
- How to connect to your corporate office using a VPN
- How to optimize your router for gaming and voice
- How to remotely change your router settings
- How to enable Voice over IP on your network
- How to configure UPnP
- How to use a router as an access point
- How to put your new router behind an existing router
- How to expose a device to the Internet
- Improving Security
- Port Forwarding and Port Triggering
- Maintaining and Monitoring
- Browser-based Utility Menu Structure
- Specifications
- Product overview
- Setting Up: Basics
- How to create a home network
- Where to find more help
- How to set up your router
- How to improve your wireless connection speed
- How to test your Internet connection speed
- How to connect devices to your network
- How to set up parental controls
- How to set up guest access to your network
- How to change your router’s name and password
- Setting Up: Advanced
- How to open the browser-based utility
- How to manually set up your router
- How to get the most out of your dual-band router
- How to set up the DHCP server on your router
- How to find your network on the Internet
- How to clone a MAC address
- How to connect to your corporate office using a VPN
- How to optimize your router for gaming and voice
- How to remotely change your router settings
- How to enable Voice over IP on your network
- How to configure UPnP
- How to use a router as an access point
- How to put your new router behind an existing router
- How to expose a device to the Internet
- Improving Security
- Port Forwarding and Port Triggering
- Maintaining and Monitoring
- Browser-based Utility Menu Structure
- Specifications
- Product overview
- Setting Up: Basics
- How to create a home network
- Where to find more help
- How to set up your router
- How to improve your wireless connection speed
- How to test your Internet connection speed
- How to connect devices to your network
- How to set up parental controls
- How to set up guest access to your network
- How to change your router’s name and password
- Setting Up: Advanced
- How to open the browser-based utility
- How to manually set up your router
- How to get the most out of your dual-band router
- How to set up the DHCP server on your router
- How to find your network on the Internet
- How to clone a MAC address
- How to connect to your corporate office using a VPN
- How to optimize your router for gaming and voice
- How to remotely change your router settings
- How to enable Voice over IP on your network
- How to configure UPnP
- How to use a router as an access point
- How to put your new router behind an existing router
- How to expose a device to the Internet
- Improving Security
- Using an External Drive
- Port Forwarding and Port Triggering
- Maintaining and Monitoring
- Browser-based Utility Menu Structure
- Specifications
- Product overview
- Setting Up: Basics
- How to create a home network
- Where to find more help
- How to set up your router
- How to improve your wireless connection speed
- How to test your Internet connection speed
- How to connect devices to your network
- How to set up parental controls
- How to set up guest access to your network
- How to change your router’s name and password
- Setting Up: Advanced
- How to open the browser-based utility
- How to manually set up your router
- How to get the most out of your dual-band router
- How to set up the DHCP server on your router
- How to find your network on the Internet
- How to clone a MAC address
- How to connect to your corporate office using a VPN
- How to optimize your router for gaming and voice
- How to remotely change your router settings
- How to enable Voice over IP on your network
- How to configure UPnP
- How to use a router as an access point
- How to put your new router behind an existing router
- How to expose a device to the Internet
- Improving Security
- Using an External Drive
- Port Forwarding and Port Triggering
- Maintaining and Monitoring
- Browser-based Utility Menu Structure
- Specifications
61
Maintaining and Monitoring
Linksys E-Series
5.
Select the log you want to see from the Type drop-down list.
• Incoming Log—The source IP addresses and destination port
numbers for incoming Internet traffic
• Outgoing Log—Local IP addresses, destination URLs/IP addresses,
and service/port numbers for outgoing Internet traffic
• Security Log—Logins for the browser-based utility
• DHCP Client Log—Local DHCP server status information
6.
To save the log, click Save the Log, then click OK or Save.
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
Industry Canada statement:
This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils
radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le
dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout
brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable.
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20
cm de distance entre la source de rayonnement et votre corps.