ADSL Gateway User Guide Model No.
ADSL Gateway Copyright and Trademarks Specifications are subject to change without notice. Linksys is a registered trademark or trademark of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Copyright © 2006 Cisco Systems, Inc. All rights reserved. Other brands and product names are trademarks or registered trademarks of their respective holders.
ADSL Gateway Table of Contents Chapter 1: Introduction 1 Welcome What’s in this User Guide? 1 2 Chapter 2: Planning Your Network 4 The Gateway’s Functions IP Addresses Chapter 3: Getting to Know the ADSL Gateway 4 4 6 Ports and Reset Button on Side Panel LEDs on Side Panel The Bottom Panel 6 7 8 Chapter 4: Connecting the ADSL Gateway 9 Overview Connecting the Gateway to a Computer 9 9 Chapter 5: Configuring the ADSL Gateway 11 Overview How to Access the Web-based Utility The Setup Tab The
ADSL Gateway Appendix F: Warranty Information Appendix G: Regulatory Information Appendix H: Contact Information 65 66 72
ADSL Gateway List of Figures Figure 2-1: Network Figure 3-1: Ports and Reset Button on Side Panel Figure 3-2: LEDs on Side Panel Figure 3-3: Bottom Panel with Stand in Closed Position Figure 3-4: Gateway Using Stand Figure 4-1: Connect the ADSL Line Figure 4-2: Connect a PC Figure 4-3: Connect the Power Figure 5-1: Login Screen Figure 5-2: Basic Setup Figure 5-3: RFC 1483 Bridged - Dynamic IP Figure 5-4: RFC 1483 Bridged - Static IP Figure 5-5: RFC 1483 Routed Figure 5-6: IPoA Figure 5-7: RFC 2516 PPPoE Fi
ADSL Gateway Figure 5-25: List of PCs Figure 5-26: Add/Edit Service Figure 5-27: Single Port Forwarding Figure 5-28: Port Range Forwarding Figure 5-29: Port Triggering Figure 5-30: DMZ Figure 5-31: QoS Figure 5-32: Edit List of QoS Settings Figure 5-33: Management Figure 5-34: Allowed IP - IP Range Figure 5-35: Reporting Figure 5-36: System Log Figure 5-37: Ping Test Figure 5-38: Backup&Restore Figure 5-39: Factory Defaults Figure 5-40: Firmware Upgrade Figure 5-41: Reboot Figure 5-42: Gateway Figure 5-43:
ADSL Gateway Chapter 1: Introduction Welcome Thank you for choosing the AG300 ADSL Gateway. This Gateway will provide your computers with a high-speed Internet connection as well as access to local resources, including files and printers. How does the Gateway do all of this? By connecting the Internet, as well as your computers and peripherals, to the Gateway, you create a LAN, or Local Area Network.
ADSL Gateway What’s in this User Guide? This user guide covers the steps for setting up and using the ADSL Gateway. • Chapter 1: Introduction This chapter describes applications of the ADSL Gateway and this User Guide. • Chapter 2: Planning Your Network This chapter describes the basics of networking. • Chapter 3: Getting to Know the ADSL Gateway This chapter describes the physical features of the Gateway.
ADSL Gateway • Appendix H: Contact Information This appendix provides contact information for a variety of Linksys resources, including Technical Support.
ADSL Gateway Chapter 2: Planning Your Network The Gateway’s Functions A Gateway is a network device that connects two networks together. In this instance, the Gateway connects your Local Area Network (LAN), or the group of computers in your home or office, to the Internet. The Gateway processes and regulates the data that travels between these two networks. The Gateway’s NAT feature protects your network of computers so users on the public, Internet side cannot “see” your computers.
ADSL Gateway Since you use the Gateway to share your DSL Internet connection, contact your ISP to find out if they have assigned a static IP address to your account. If so, you will need that static IP address when configuring the Gateway. You can get that information from your ISP. Dynamic IP Addresses A dynamic IP address is automatically assigned to a device on the network, such as computers and print servers.
ADSL Gateway Chapter 3: Getting to Know the ADSL Gateway Ports and Reset Button on Side Panel The Gateway’s ports and Reset button are located on a side panel. Figure 3-1: Ports and Reset Button on Side Panel Line The Line port connects to the ADSL line. Ethernet (1-4) The Ethernet ports connect to your computers and other network devices. Reset Button There are two ways to reset the Gateway's factory defaults.
ADSL Gateway LEDs on Side Panel The Gateway's LEDs, which indicate network activity, are located on the other side panel. Figure 3-2: LEDs on Side Panel POWER Green. The POWER LED lights up when the Gateway is powered on. ETHERNET (1-4) Green. The ETHERNET LED serves two purposes. If the LED is continuously lit, the Gateway is successfully connected to a device through the LAN port. If the LED is flashing, it is an indication of any network activity. DSL Green.
ADSL Gateway The Bottom Panel The Gateway has a built-in stand available. If you place the Gateway flat on a surface, then you can leave the stand in the closed position. However, if you want the Gateway to be upright, swivel the stand clockwise 90º and position the Gateway accordingly.
ADSL Gateway Chapter 4: Connecting the ADSL Gateway Overview The installation technician from your ISP should have left the setup information for the modem with you after installing your broadband connection. If not, you can call your ISP to request that data. After you have the setup information you need for your specific type of Internet connection, you can begin installation and setup of the Gateway. Continue to “Connecting the Gateway to a Computer.” Connecting the Gateway to a Computer 1.
ADSL Gateway 3. Connect one end of an Ethernet network cable to one of the Ethernet ports (labeled 1-4) on the back of the Gateway, and the other end to an Ethernet port on a computer. Repeat this step to connect more computers, a switch, or other network devices to the Gateway. 4. Connect the power adapter to the Gateway’s Power port, and then plug the power adapter into a power outlet. NOTE: You should always plug the Gateway’s power adapter into a power strip with surge protection.
ADSL Gateway Chapter 5: Configuring the ADSL Gateway Overview Follow the steps in this chapter and use the Gateway’s web-based utility to configure the Gateway. This chapter will describe each web page in the Utility and each page’s key functions. The utility can be accessed via your web browser through use of a computer connected to the Gateway.
ADSL Gateway Security • Firewall. To disable or enable the firewall, set up filters, and block WAN requests, click this tab. • VPN. To enable or disable Virtual Private Network (VPN) passthrough, or to set up an IPSec VPN tunnel, use this screen. vpn (virtual private network): a security measure to protect data as it leaves one network and goes to another over the Internet. Access Restrictions • Internet Access. This screen allows you to control the Internet usage and traffic on your local network.
ADSL Gateway • Reboot. If you need to do a hard or soft reboot of the Gateway, use this screen. Status • Gateway. This screen provides status information about the Gateway. • Local Network. This provides status information about the local network. • DSL Connection. This screen provides status information about the DSL connection.
ADSL Gateway • Multiplexing: Select LLC or VC, depending on your ISP. • QoS Type: Select from the drop-down menu: CBR (Continuous Bit Rate) to specify fixed bandwidth for voice or data traffic; UBR (Unspecific Bit Rate) for application that are none-time sensitive, such as e-mail; or VBR (Variable Bite Rate) for Bursty traffic and bandwidth-sharing with other applications. • Pcr Rate: For the Peak Cell Rate, divide the DSL line rate by 424 to get the maximum rate the sender can send cells.
ADSL Gateway RFC 1483 Routed If you are required to use RFC 1483 Routed, then select RFC 1483 Routed. • Internet IP Address. This is the Gateway’s IP address, when seen from the WAN, or the Internet. Your ISP will provide you with the IP Address you need to specify here. • Subnet Mask. This is the Gateway’s Subnet Mask. Your ISP will provide you with the Subnet Mask. • Gateway. Your ISP will provide you with the default Gateway Address, which is the ISP server’s IP address.
ADSL Gateway RFC 2516 PPPoE Some DSL-based ISPs use PPPoE (Point-to-Point Protocol over Ethernet) to establish Internet connections. If you are connected to the Internet through a DSL line, check with your ISP to see if they use PPPoE. If they do, you will have to enable PPPoE. • Service Name. Enter the name of your PPPoE service in this field. • User Name and Password. Enter the User Name and Password provided by your ISP. • Connect on Demand: Max Idle Time.
ADSL Gateway Bridged Mode Only If you are using your Gateway as a bridge, which makes the Gateway act like a stand-alone modem, select Bridged Mode Only. All NAT and routing settings are disabled in this mode. Optional Settings (required by some ISPs) • Host Name and Domain Name. These fields allow you to supply a host and domain name for the Gateway. Some ISPs require these names as identification.
ADSL Gateway • Starting IP Address. Enter a value for the DHCP server to start with when issuing IP addresses. This value must be 192.168.1. 2 or greater, because the default IP address for the Gateway is 192.168.1.1. • Maximum Number of DHCP Users. Enter the maximum number of users/clients that can obtain an IP address. The number will vary depending on the starting IP address entered. • Client Lease Time.
ADSL Gateway DynDNS.org • User Name, Password, and Host Name. Enter the User Name, Password, and Host Name of the account you set up with DynDNS.org. • Internet IP Address. The Gateway’s current Internet IP Address is displayed here. Because it is dynamic, it will change. • Status. The status of the DDNS service connection is displayed here. TZO.com • E-mail Address, Password, and Domain Name. Enter the E-mail Address, Password, and Domain Name of the account you set up with TZO. Figure 5-12: DynDNS.
ADSL Gateway The Advanced Routing Tab The Advanced Routing screen allows you to configure the NAT, dynamic routing, and static routing settings. Advanced Routing • Operating Mode. In this section, you will configure the Gateway’s general routing settings. • NAT. NAT is a security feature that is enabled by default. It enables the Gateway to translate IP addresses of your local area network to a different IP address for the Internet. To disable NAT, click the Disabled radio button. • Dynamic Routing.
ADSL Gateway • Subnet Mask. Enter the Subnet Mask (also known as the Network Mask), which determines which portion of an IP address is the network portion, and which portion is the host portion. • Gateway. Enter the IP address of the gateway device that allows for contact between the Gateway and the remote network or host. • Hop Count. Hop Count is the number of hops to each node until the destination is reached (16 hops maximum). Enter the Hop Count in the field provided.
ADSL Gateway Apply. To enable the selection criteria on one line of the table, click that line’s Apply box so a check appears in it. To disable the line’s criteria, click the box to clear. When you have finished making changes in this window, click the Save button to save the changes, or click the Cancel button to undo your changes. Then click Close. You will be returned to the Advanced Routing panel.
ADSL Gateway The Security Tab The Security tab gives you access to firewall and VPN (virtual private network) settings. The Firewall Tab This panel shows firewall and filter settings. Use these features to enhance the security of your network. Firewall You can enable or disable the firewall, select filters to block specific Internet data types, and block anonymous Internet requests. Figure 5-17: Firewall To use the firewall, click Enable. If you do not want to use the firewall, click Disable.
ADSL Gateway Page button to go to the previous page of information. Click the Next Page button to move to the next page of information. When finished making your changes on this tab, click the Save Settings button to save these changes, or click the Cancel Changes button to undo your changes. The VPN Tab This panel shows VPN (virtual private network) settings. You can disable or enable passthrough for four kinds of VPNs.
ADSL Gateway • Delete: Click this button to delete the selected tunnel. • Summary: Click this button to see a summary of your IPSec settings and the tunnels’ status. • IPSec VPN Tunnel: Click Enabled to enable the selected tunnel, or Disabled to disable it. • Tunnel Name: Click and type in this box to give the selected tunnel a name. A name is required, but is only for your reference and need not match the name used at the remote gateway or client.
ADSL Gateway • To use manual key management, select Manual, enter authentication and encryption keys (these must be identical to those entered at the remote end), and enter inbound and outbound SPIs (security parameter indexes). The SPIs must be exactly complementary to those entered at the remote end. When you select automatic key management, an Advanced Settings button appears. Click this button if there are special requirements for this IPSec tunnel.
ADSL Gateway The Access Restriction Tab The Internet Access Tab The Internet Access tab allows you to block or allow specific kinds of Internet usage. You can set up Internet access policies for specific computers and block websites by URL address or keyword. Internet Access Policy. Access can be managed by a policy. Use the settings on this screen to establish an access policy (after the Save Settings button is clicked). Selecting a policy from the drop-down menu will display that policy’s settings.
ADSL Gateway 4. Click the Edit List of PCs button to select which PCs will be affected by the policy. The List of PCs screen will appear. You can select a PC by MAC Address or IP Address. You can also enter a range of IP Addresses if you want this policy to affect a group of PCs. After making your changes, click the Save Settings button to apply your changes or Cancel Changes to cancel your changes. 5.
ADSL Gateway The Applications & Gaming Tab The Single Port Forwarding Tab Single Port Forwarding Use the Single Port Forwarding screen when you want to open a specific port so users on the Internet can see the servers behind the Gateway (such servers may include FTP or e-mail servers). When users send this type of request to your network via the Internet, the Gateway will forward those requests to the appropriate computer.
ADSL Gateway The Port Range Forwarding Tab The Port Range Forwarding screen sets up public services on your network, such as web servers, ftp servers, email servers, or other specialized Internet applications. (Specialized Internet applications are any applications that use Internet access to perform functions such as videoconferencing or online gaming. Some Internet applications may not require any forwarding.
ADSL Gateway The Port Triggering Tab Port Triggering is used for special applications that can request a port to be opened on demand. For this feature, the Gateway will watch outgoing data for specific port numbers. The Gateway will remember the IP address of the computer that sends a transmission requesting data, so that when the requested data returns through the Gateway, the data is pulled back to the proper computer by way of IP address and port mapping rules. • Application.
ADSL Gateway The QoS Tab QoS Quality of Service (QoS) ensures better service to high-priority types of network traffic, which may involve demanding, real-time applications, such as Internet phone calls or videoconferencing. Enabled/Disabled. To use QoS, select Enabled. Otherwise, keep the default, Disabled. PVC QoS Priority PVC-based QoS assigns different levels of priority, or precedence, to different permanent virtual circuits.
ADSL Gateway Fragment packets’ size of AF and BE traffic to be equal to the size of EF traffic: Enable this option and input a packet size to have large Assured Forwarding (medium priority) and Best Effort (low priority) packets fragmented so they will not uduly delay Expedited Forwarding (high priority) packets. The value you enter should be from 68 to 1492. When you have finished making changes in this window, click the Save button to save the changes, or click the Cancel button to undo your changes.
ADSL Gateway The Administration Tab The Management Tab The Management screen allows you to change the Gateway’s access settings as well as configure the SNMP (Simple Network Management Protocol), UPnP (Universal Plug and Play), IGMP (Internet Group Multicast Protocol)-Proxy, and WLAN management features. Gateway Access Local Gateway Access. To ensure the Gateway’s security, you will be asked for your password when you access the Gateway’s Web-based Utility. The default username and password is admin.
ADSL Gateway SNMP SNMP is a popular network monitoring and management protocol. To enable SNMP, click Enabled. To disable SNMP, click Disabled. If enabled, then specify the IP address(es) allowed to have SNMP access. Select All to allow all IP addresses with no restrictions, IP address to specify a single IP address, or IP range to specify a range of IP addresses. • Device Name. Enter the name of the Gateway. • SNMP V1/V2: Get Community.
ADSL Gateway • PVC Available. Select the number of the PVC over which you wish IGMP-Proxy to work. • IGMP Proxy. To use this feature, select Enable. Otherwise, select Disable. IGMP-Snooping The multicast packets used by some multimedia applications are treated as broadcast packets and sent to all of the Gateway’s LAN ports. If this results in too much traffic going to ports over which the application is not being used, you can enable IGMP snooping to ensure correct routing of multicast traffic.
ADSL Gateway The Reporting Tab The Reporting screen provides you with a log of all incoming and outgoing URLs or IP addresses for your Internet connection. It also provides logs for VPN and firewall events. Reporting • Log. To enable log reporting, click Enable. • Logviewer IP Address. Enter the IP Address of the computer that will receive logs. You will need Logviewer software to view these logs. This free software is available for download from www.linksys.com. Email Alerts • E-Mail Alerts.
ADSL Gateway The Diagnostics Tab Ping Test Ping Test Parameters • Ping Target IP. Enter the IP address that you want to ping. This can be either a local (LAN) IP or an Internet (WAN) IP address. • Ping Size. Enter the size of the packet. • Number of Pings. Enter the number of times that you want to ping. • Ping Interval. Enter the ping interval (how often the target IP address will be pinged) in milliseconds. Figure 5-37: Ping Test • Ping Timeout.
ADSL Gateway The Factory Defaults Tab Restore Factory Defaults. If you wish to restore the Gateway to its factory default settings and lose all your settings, click Yes. To begin the restore process, click the Save Settings button to save these changes, or click the Cancel Changes button to undo your changes. The Firmware Upgrade Tab Figure 5-39: Factory Defaults The Gateway allows you to upgrade firmware from the LAN (Local Area Network) side of the Gateway.
ADSL Gateway The Status Tab The Gateway Tab This screen displays information about the Gateway and its Internet connection. Gateway Information This section displays the Gateway’s Firmware Version, MAC Address, and Current Time. Internet Connection This section shows the following information: the Connection, Login Type, Interface, IP Address, Subnet Mask, Default Gateway, DNS 1, 2, and 3 server IP addresses, and WINS address.
ADSL Gateway The Local Network Tab The Local Network information that is displayed is the local MAC address, IP address, subnet mask, DHCP server status, and DHCP start and end IP addresses. To view the DHCP Clients Table, click the DHCP Clients Table button. To view the ARP/RARP Table, click the ARP/RARP Table button. DHCP Client Table. The DHCP Active IP Table shows the current DHCP Client data.
ADSL Gateway The DSL Connection Tab This screen shows information about the DSL connection and PVC connections. DSL Status This section shows the following: DSL Status, DSL Modulation Mode, DSL Path Mode, Downstream Rate, Upstream Rate, Downstream Margin, Upstream Margin, Downstream Line Attenuation, Upstream Line Attenuation, Downstream Transmit Power, and Upstream Transmit Power. PVC Connection Connection: To view information about a particular PVC, select that PVC’s number from this list.
ADSL Gateway Appendix A: Troubleshooting This appendix consists of two parts: “Common Problems and Solutions” and “Frequently Asked Questions.” Provided are possible solutions to problems that may occur during the installation and operation of the Gateway. Read the descriptions below to help you solve your problems. If you can’t find an answer here, check the Linksys international website at www.linksys.com/international. Common Problems and Solutions 1. I need to set a static IP address on a computer.
ADSL Gateway 7. Toward the bottom of the window, select Use the following DNS server addresses, and enter the Preferred DNS server and Alternative DNS server (provided by your ISP). Contact your ISP or go on its website to find the information. 8. Click the OK button in the Internet Protocol (TCP/IP) Properties window, and click the OK button in the Local Area Connection Properties window. 9. Restart the computer if asked.
ADSL Gateway For Windows 98 and Me: • Click Start and Run. In the Open field, type in command. Press the Enter key or click the OK button. For Windows NT, 2000, and XP: • Click Start and Run. In the Open field, type cmd. Press the Enter key or click the OK button. In the command prompt, type ping 192.168.1.1 and press the Enter key. • If you get a reply, the computer is communicating with the Gateway.
ADSL Gateway 3. Refer to “Problem #10: I am a PPPoE user, and I need to remove the proxy settings or the dial-up popup window.” 5. I can’t get my Virtual Private Network (VPN) working through the Gateway. Access the Gateway’s web interface by going to http://192.168.1.1 or the IP address of the Gateway, and go to the Security tab. Make sure you have IPsec passthrough and/or PPTP pass-through enabled.
ADSL Gateway field provided. Check “Appendix B: Finding the MAC Address and IP Address for Your Ethernet Adapter” for details on getting an IP address. 6. Check the Enable option for the port services you want to use. Consider the example below: Customized Application Web server FTP server SMTP (outgoing) POP3 (incoming) External Port 80 to 80 21 to 21 25 to 25 110 to 110 TCP X X X X UDP IP Address 192.168.1.100 192.168.1.101 192.168.1.102 192.168.1.
ADSL Gateway 8. I can’t get the Internet game, server, or application to work. If you are having difficulties getting any Internet game, server, or application to function properly, consider exposing one computer to the Internet using DeMilitarized Zone (DMZ) hosting. This option is available when an application requires too many ports or when you are not sure which port services to use.
ADSL Gateway • For Netscape 4.7 or higher: 1. Start Netscape Navigator, and click Edit, Preferences, Advanced, and Proxies. 2. Make sure you have Direct connection to the Internet selected on this screen. 3. Close all the windows to finish. 11. To start over, I need to set the Gateway to factory default. Hold the Reset button for 10 seconds and then release it. This will return the Internet settings, password, forwarding, and other settings on the Gateway to the factory default settings.
ADSL Gateway 1. To connect to the Gateway, go to the web browser, and enter http://192.168.1.1 or the IP address of the Gateway. 2. Enter the username and password, if asked. (The default username and password is admin.) 3. On the Setup screen, select the option Keep Alive, and set the Redial Period option at 20 (seconds). 4. Click the Save Settings button. Click the Status tab, and click the Connect button. 5. You may see the login status display as Connecting.
ADSL Gateway • If the Gateway is configured correctly, check your Internet connection (DSL/cable modem, etc.) to see if it is working correctly. You can remove the Gateway to verify a direct connection. • Manually configure the TCP/IP settings with a DNS address provided by your ISP. • Make sure that your browser is set to connect directly and that any dial-up is disabled. For Internet Explorer, click Tools, Internet Options, and then the Connection tab.
ADSL Gateway What is Network Address Translation and what is it used for? Network Address Translation (NAT) translates multiple IP addresses on the private LAN to one public address that is sent out to the Internet. This adds a level of security since the address of a computer connected to the private LAN is never transmitted on the Internet. Furthermore, NAT allows the Gateway to be used with low cost Internet accounts when only one TCP/IP address is provided by the ISP.
ADSL Gateway The web page hangs; downloads are corrupt, or nothing but junk characters are being displayed on the screen. What do I need to do? Force your Ethernet adapter to 10Mbps or half duplex mode, and turn off the “Auto-negotiate” feature of your Ethernet adapter as a temporary measure. (Please look at the Network Control Panel in your Ethernet adapter’s Advanced Properties tab.) Make sure that your proxy setting is disabled in the browser. Check our website at www.linksys.
ADSL Gateway Is the Gateway cross-platform compatible? Any platform that supports Ethernet and TCP/IP is compatible with the Gateway. How many ports can be simultaneously forwarded? Theoretically, the Gateway can establish 520 sessions at the same time, but you can only forward 10 ranges of ports. What are the advanced features of the Gateway? The Gateway’s advanced features include VPN settings, Filters, Port Forwarding, Routing, and DDNS.
ADSL Gateway Appendix B: Finding the MAC Address and IP Address for Your Ethernet Adapter This section describes how to find the MAC address for your computer’s Ethernet adapter so you can use the MAC filtering feature of the Gateway. You can also find the IP address of your computer’s Ethernet adapter. This IP address is used for the Gateway’s filtering, forwarding, and/or DMZ features. Follow the steps in this appendix to find the adapter’s MAC or IP address in Windows 98, Me, 2000, or XP.
ADSL Gateway Windows 2000 or XP Instructions 1. Click Start and Run. In the Open field, enter cmd. Press the Enter key or click the OK button. Note: The MAC address is also called the Physical Address. 2. At the command prompt, enter ipconfig /all. Then press the Enter key. 3. Write down the Physical Address as shown on your computer screen (Figure C-3); it is the MAC address for your Ethernet adapter. This appears as a series of numbers and letters.
ADSL Gateway Appendix C: Upgrading Firmware To upgrade the Gateway’s firmware: 1. Download the Gateway’s firmware upgrade file from www.linksys.com. 2. Extract the file on your computer. 3. Open the Gateway’s Web-based Utility and click the Administration tab. 4. Click the Firmware Upgrade tab. 5. Click the Browse button to find the extracted file, and then double-click it. 6. Click the Upgrade button, and follow the on-screen instructions.
ADSL Gateway Appendix D: Glossary This glossary contains some basic networking terms you may come across when using this product. For more advanced terms, see the complete Linksys glossary at http://www.linksys.com/glossary. Access Point - A device that allows wireless-equipped computers and other devices to communicate with a wired network. Also used to expand the range of a wireless network.
ADSL Gateway DMZ (Demilitarized Zone) - Removes the Router's firewall protection from one PC, allowing it to be "seen" from the Internet. DNS (Domain Name Server) - The IP address of your ISP's server, which translates the names of websites into IP addresses. Domain - A specific name for a network of computers. Download - To receive a file transmitted over a network. DSL (Digital Subscriber Line) - An always-on broadband connection over traditional phone lines.
ADSL Gateway IP Address - The address used to identify a computer or device on a network. IPCONFIG - A Windows 2000 and XP utility that displays the IP address for a particular networking device. IPSec (Internet Protocol Security) - A VPN protocol used to implement secure exchange of packets at the IP layer. ISP (Internet Service Provider) - A company that provides access to the Internet. LAN - The computers and networking products that make up your local network.
ADSL Gateway RJ-45 (Registered Jack-45) - An Ethernet connector that holds up to eight wires. Roaming - The ability to take a wireless device from one access point's range to another without losing the connection. Router - A networking device that connects multiple networks together. Server - Any computer whose function in a network is to provide user access to files, printing, communications, and other services. SMTP (Simple Mail Transfer Protocol) - The standard e-mail protocol on the Internet.
ADSL Gateway TKIP (Temporal Key Integrity Protocol) - a wireless encryption protocol that provides dynamic encryption keys for each packet transmitted. Topology - The physical layout of a network. TX Rate - Transmission Rate. Upgrade - To replace existing software or firmware with a newer version. Upload - To transmit a file over a network. URL (Uniform Resource Locator) - The address of a file located on the Internet.
ADSL Gateway Appendix E: Specifications Model Number AG300 Standards ANSI T1.413 Issue 2, ITU G.992.1 (G.dmt), G.992.2 (G.lite), G.992.3 (ADSL2), G.992.4 (ADSL2 Lite), G.992.5 (ADSL2+), G.994.1 (G.hs), G.996.1 (G.
ADSL Gateway Operating Temp. 0º~40ºC (32º~104ºF) Storage Temp.
ADSL Gateway Appendix F: Warranty Information Linksys warrants to You that, for a period of three years (the “Warranty Period”), your Linksys Product will be substantially free of defects in materials and workmanship under normal use. Your exclusive remedy and Linksys' entire liability under this warranty will be for Linksys at its option to repair or replace the Product or refund Your purchase price less any rebates. This limited warranty extends only to the original purchaser.
ADSL Gateway Appendix G: Regulatory Information FCC Statement This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications.
ADSL Gateway User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste Electric and Electronic Equipment (WEEE) This document contains important information for users with regards to the proper disposal and recycling of Linksys products.
ADSL Gateway Appendix G: Regulatory Information 68
ADSL Gateway Appendix G: Regulatory Information 69
ADSL Gateway Appendix G: Regulatory Information 70
ADSL Gateway For more information, visit www.linksys.com.
ADSL Gateway Appendix H: Contact Information Need to contact Linksys? Visit us online for information on the latest products and updates to your existing products at: http://www.linksys.com/international If you experience problems with any Linksys product, you can e-mail us at: In Europe E-mail Address Austria support.at@linksys.com Belgium support.be@linksys.com Denmark support.dk@linksys.com France support.fr@linksys.com Germany support.de@linksys.com Italy support.it@linksys.
