Datasheet

REMOTE TRIGGERS >20
LDT-4GLAT-4G
All Linkstar ash units come standard with a sync cable. The
accessories below provide extra options for various flash
setups, such as ashing through slave/infrared or wireless.
Triggers
For Studio Flashes
LAT-4G / LDT-4G
These universal remote radio trigger sets enable you to work
completely wireless. The advantage over any other wireless
solution (infrared or slave ashing) is the fact that the signal
from these sets cannot be obstructed: it always works.
The transmitter has a range of about 15 meters and works
about 1 year or 20.000 ashes on the battery that comes
with it. It is compatible with any camera that has a flash
shoe connector on top. For Sony/Minolta cameras, a HS-
25Sa hotshoe must be used (see below).
The receiver of the LAT-4G set is connected between the
ash unit and its power cable. Some brands have a different
type of power cable or the cable cannot be removed from
the unit. For these flashes, the LDT-4G set with battery
operated receiver can be used. This receiver works about
1200 hours on one set of AA batteries.
Model LAT-4G LDT-4G
Article Number 560848 560847
Sender power source CR-23A (incl.) CR-23A (incl.)
Receiver power source AC 220-240 50 Hz 2 x AA/1.5v (not incl.)
Trigger Delay 1/16000 sec 1/16000 sec
Sync Speed <1/125 sec <1/125 sec
Channels 4 4
HS-15 Hotshoe
With 1/4" thread and sync
connector. Put your cameraash
on a light stand and trigger
it remotely using either the
camera ash's slave sensor
or the sync connector on the
hotshoe. Art.nr. 560853
HS-25Sa Hotshoe
For Sony/Minolta. Must be
used for the sender of the
wireless trigger sets (see above)
Art.nr. 560859
HS-25A3 Hotshoe & Cable
With 1/4" thread, sync cable
and sync connector. Put your
cameraash on a light stand
and trigger it remotely using
either the camera ash's slave
sensor or the sync connector on
the hotshoe. Art.nr. 560856
HS-25C Hotshoe
With 1/4" thread and sync
connector. Put your cameraash
on a light stand and trigger
it remotely using either the
camera ash's slave sensor
or the sync connector on the
hotshoe. Art.nr. 560858
HS-25B Hotshoe
If your camera has no sync
jacket, you can use this hot
shoe to connect a sync cable to
your camera. Art.nr. 560857
HS-25D Hotshoe
With 2 sync jackets (male and
female) and test button.
Art.nr. 560860
PS-35 Plug-in Sensor
Used for triggering any
sync connection: directly on
a studioash or through a
hotshoe. Art.nr. 560854
PSL-15 Sensor/Hotshoe
If you want to trigger your
camera ash remotely but it
doesn't have a slave sensor,
use this. With 1/4" thread.
Art.nr. 560852
PSS-10 Sensor
With sync-jacket
and suction cup.
Art.nr. 560851
PSL-25 Sensor/Hotshoe
With 1/4" thread, slave
sensor and sync-jacket.
Art.nr. 560855
Sync Cable
S-353
3,5 mm jack plug
Length: 5 meters
Art.nr. 561201
Length: 30 cm
Art.nr. 561198
Sync Cable
S-2503
2,5 mm jack plug
Length: 30 cm
Art.nr. 561200
Sync Cable
S-635
6,3 mm jack plug
Length: 5 meters
Art.nr. 561203
Length: 30 cm
Art.nr. 561199
Sync Cable
S-50x
2 x X-contact
Length: 5 meters
Art.nr. 561204
IR-1 Infrared Trigger
This infrared trigger ts on the
ash shoe of your camera. It
triggers the ashes through an
infrared signal. Works with
all ashes that have a built-in
slave sensor.
Art.nr. 560850