Solar Motion Sensor Security Light
Table of Contents Table of Contents ..............................2 Package Contents ............................4 Safety Information ............................2 Installation ........................................5 Pre-Installation ...................................2 Operation ..........................................8 Planning Installation .........................2 Care and Cleaning ............................11 Specifications ......................................3 Troubleshooting ........
Specifications Range Up to 27 ft. (8 m) (Varies with surrounding temperature) Sensing angle Up to 110° Lumens 700+/-10% Power requirements 2*3.
Pre-Installation(continued) Hardware Included NOTE: Hardware shown to actual size.
Part Description Quantity A Lamp head 1 B Light fixture 1 C Motion sensor 1 D Mounting plate 1 Installation 1 Determining the mounting location NOTE: The light fixture should be mounted approximately 7 ft. (2.0 m) above the ground. Determine the mounting location – wall mount only. Position the lamp head (A) in the general direction of the desired light coverage.
2 Removing the mounting plate NOTE: This fixture comes with a mounting plate (D). It is pre-assembled on the light fixture (B) for shipping. Unscrew the decorative screw (CC) in the bottom of the fixture (B), and pull the mounting plate (D) from the fixture. 3 Installing the mounting plate Place the mounting plate (D) against the mounting surface and ensure the mounting plate (D) is level. Drill two holes (1) through the mounting plate (D) and into the mounting surface.
4 Installing the solar panel NOTE: Ensure that the solar panel is angled so that it receives the maximum amount of sun exposure. The solar panel cable is 3m, mark and drill 4 holes in the location where you want to mount the solar panel. Use the mounting base template on the bottom of the solar panel to make your marks. Insert the wall anchors(BB) and mounting screws(AA) (included)in the holes. Place the mounting base over the holes and slide the screws through the solar panel base and into the anchors.
5 Mounting the light fixture Slide the light fixture (B) onto the mounting plate (D), screw the decorative screw (CC) in the bottom of the fixture (D) and tighten securely. 6 Connect the solar panel with light NOTE: Connect the solar panel with light, exposed solar panel under sunlight for 12 hours before first use. Operation 1 Adjusting the lamp head If needed, gently grasp the lamp head (A) and tilt or rotate to adjust the light coverage area.
2 Setting the sensor for testing NOTE: User can turn the control knob TIME to adjust the duration of the illumination from approx. 3 seconds to 7 minutes (+/-10%). User can turn the control knob LUX to adjust the daylight level at which to activate the motion detector. 3 Adjusting the TIME control NOTE: The “TIME” control determines the amount of time the light will stay on full bright after all motion has stopped. User can turn the control knob TIME to adjust the duration of the illumination from approx.
4 Adjusting the LUX control NOTE: The “LUX” control determines how dark the surrounding light level needs to be before the motion sensor (C) will turn on the light when motion is detected. Turn the control knob LUX to adjust the daylight level: At the position , the motion detector will only react at night. In the position , the motion detector will respond at daylight levels. 5 Adjusting the motion sensor detection zone Perform a “walk test”: walk in an arc across the front of the motion sensor (C).
Care and Cleaning To prolong the original appearance, clean the light fixture with clear water and a soft, damp cloth only. Do not use paints, solvents, or other chemicals on this light fixture. They could cause a premature deterioration of the finish. This is not a defect in the finish and will not be covered by the warranty. Do not spray the light fixture with a hose or power washer.
LINK2HOME 1 YEAR LIMITED WARRANTY IMPORTANT: Proof of Purchase is required to obtain warranty service Paragon Group USA Inc. warrants to the original owner that our products will be free from defect in workmanship and material for a period of ONE YEAR from the date of purchase. Should any unit(s) prove to be defective during this period, Paragon Group USA Inc. will be responsible for replacement of the defective unit(s) only. Paragon Group USA Inc.
