User guide

August 30, 2002 Manual Version 1.0
2.8
Section 2.3 Wiring System Modules and Components
Section 2.3.1 Conduit Runs
Wiring between the enclosures for OmniLink II Press Automation Control components should be run in
conduit. The use of flexible liquid tight conduit with ground is suggested, but hard conduit can also be
used. Figure 2.9 shows some of the typical conduit runs that may be required.
Figure 2.9. General View of Components and Wiring Runs for Installation.
1/2” Flexible conduit
with ground for
115VAC from press
control transformer,
connections to control
dual valve output,
stop outputs from
Om niLink to press
control
.
PRESS
Stroke
Mode
Driv e
Speed
Stroke
Speed
SPM
SPM
0
0
Order
Counter
SYSTEM STATUS
Counter OFF
MAIN
SCREEN
PRESS
CONTROL
AUTO
SETS
TONNAGE
MONITOR
DIE
PROTECTION
LIMIT
SWITCH
JOB
SETUPS
0
0
MOTOR
SPEED
STATUS:
OK
STATUS:
ALL CONDITIONS OKAY
STATUS:
ALL CONDITIONS OKAY
STATUS:
ALL CONDITIONS OKAY
JOB NUMBER DESCRIPTION
100000 FRONT BRACKET
COUNTER LIMIT QUANTITY STATE
ORDER
BATCH
SPM
0
% LOAD
161
2000
500
7
7
ON
ON
READY TO STROKE
TOP
COUNTERS
CHG
ACC
CLRENT
123
456
789
0
BRAKE
MONITOR
ON
OmniLink II LCD
OPERATOR TERMINAL
LINK ELECTRIC & SAFETY CONTROL CO.
444 McNALLY DR. NASHVILLE, TN 37211
PHONE [phone]
OK
PROG RUN
OmniLink II Press Au tomation Control
Stroke
Mode
Drive
Speed
Stroke
Speed
SP M
SP M
0
0
Or de r
Co unter
SYSTEM STATUS
Co u nt e r OFF
MAI N
SCREE N
PRESS
CON TROL
AUT O
SETS
TO NNAGE
MON ITOR
DIE
PROT ECTION
LIM IT
SWITCH
JOB
SETUPS
0
0
MOT O R
SPEED
STATUS:
OK
STATUS:
ALL COND I T IONS OKAY
STATUS:
ALL CONDIT IONS OKAY
STATUS:
ALL CONDI TI ONS OKAY
JOB NUMBER DES CRIP TION
100000 FRON T BRA CKE T
COU NTER LIMI T QUANTITY STATE
ORD ER
BAT CH
SPM
0
% L OA D
161
2000
500
7
7
ON
ON
REA DY TO S TR OKE
TOP
COUN TERS
CH G
AC C
CLR
ENT
123
456
789
0
BRA KE
MONIT OR
ON
OmniLink II LCD
O PE RA T OR T ERMI N AL
LIN K E LEC TRI C & S A FE T Y CO N T ROL CO .
444 McNALLY DR . NASHVILLE, TN 37 2 11
PH O NE (61 5) 833-4168
OK
PR OG RUN
OmniLink II Press Au tomation Control
PR ESS
CONTROL
RESOLVER
CRANK OR
E CCENT RIC
CHAIN
1/2’ Flexible liquid tight
conduit with ground for
2500 Resolver cable. (3/4”
for 5000 Resolver.)
1/2” Flexible liquid tight
conduit with ground for
high speed serial bus
cable and power to
OmniLink II Press
Automation Control
optional modules
1/2” Flexible liquid tight conduit
with ground if an y op tional
low
voltage connections: setup mode
input, analog speed or motor
current signals are used.
1/2” Flex ib le liquid tight
conduit(s) with ground for
other OmniLink system
options