Owner's Manual
SETTING THE SWITCH SELECTABLE OPTIONS
There are five (5) option selection switches on the LPX1700 motor
control board that result in five (5) switch selectable options, see
Figure 17. The switches are contained in a 5-pole dip switch package
at the bottom right of the motor control board. The sections that
follows describes each of the following options they select:
Switch 1 - Safe Secure Operation Mode (Patent No. 6,611,205)
Switch 2 - Right-hand / Left Hand Installation
Switch 3 - Normally Open / Normally Closed Stop Input
Switch 4 - Pre-Move Delay and Alarm-In-Motion
Switch 5 - Slave Operation
Safe Secure™ OPEN/CLOSE PUSH BUTTON
ENABLE/DISABLE
Switch SW1 (Switch 1) controls the Open/Close Input Enable/Disable
Feature.
SWITCH 1 OFF: Activating the Open or Close buttons the gate will
open or close fully. Activation of the Open while the gate is closing
will cause it to re-open. Activation of the Close while the gate is
opening has no effect. Continuous activation of an opposing button
while the gate is on a limit will prevent operation in that direction.
Continuous signal required to move the gate when in the alarm mode.
SWITCH 1 ON: Gate does not respond to the Open or Close
pushbutton input when in the normal mode. Continuous signal required
to move the gate when in the alarm mode. This patented feature allows
a three button station to be mounted in a safe yet possibly unsecured
location as the OPEN and CLOSE buttons will only be active when in
the alarm mode. STOP is always active.
LEFT- OR RIGHT-HAND INSTALLATIONS
The LPX1700 operator can be quickly and easily configured for left-
hand or right-hand gate installations, Selectable Switch SW1 (Switch 2)
controls this option. On a normal drive installation, when standing
inside the gate and facing outwards, if the operator is on the right side
of the gate, it's a right-hand installation. If the operator is on the left
side of the gate, it's a left-hand installation. See Figure 18 for a pictorial
of a right- hand and left-hand installations.
SWITCH 2 OFF: The operator is configured for Right-hand
operation, this is how the operator is shipped from the factory.
Figure 18: Left Hand vs. Right Hand Installation
107033
Right Hand
Inside
Outside
Inside
Outside
Left Hand
SWITCH
LOCATION OF
OPTION
SW1
ON
OFF
1
2
3
4
5
R49
C6
R71
LD7
R72
R68
LD9
LD8
LD6
LD5
C18
R64
C19
R83
R32
R82
R40
R62
R22
R42
Q2
R43
C12
R54
C15
R47
R44
R53
CLO
C5
U3
LD18
R24
LD10
LD11
LD12
LD15
LD14
LD16
LD17
LD13
PB3PB2PB1
R61
R60
R5
R25
R55
D3
R31
R9
R23
R10
R8
R51
R19
R17
R13
R20
R18
R14 R65
D2
C10
R57
STOP
CLOSE
OPEN
R39
R38
R84R63
R2R1
R7R6
R16R15
R11 R12
CLOSE
OPEN
MOTOR
MOTOR
LOOP
SHADOW
EDGE
CLO
EDGE
OPN
LOOP
REV
LIMIT
LH CLO
RH OPN
LIMIT
LH OPN
RH CLO
LIMIT
MID
PHOTO
CLOSE
COM
POWER
TIMER
RECLOSE
AUTO
ADJUSTMENT
FORCE
CLOSEOPEN
C24
R59R85
U1
C2
R3 R4
R56
RO1
D8
U4
JP2
R52 R48
C14 C13
R89
C22
C9
C11
R30
R26
R29
R36
U2
TR2
TR1
TR3
P4
R77
D1
COM
COM
COM
COM
COM
24V
AC
ALT
RDO
CRO
FRE
OPN
CLO
STO
COM
OPN
PHO
CLO
PHO
REV
OPN
EDG
CLO
EDG
SHW
MST
MST
OPN
CLO
OPN
24V
AC
COM
COM
ALT
RADIO
OPEN
OPN/
RADIO
FREE
EXIT
OPEN
PUSH
CLOSE
PUSH
STOP
PUSH
OPEN
PHOTO
R87
R86
R27
R37
R46
R80
R75
R76
R79 R 73
R78 R 74
R35
R50
R28
PZ1
R21
Q3
C3
D12
R81
C25
C20
C4
C1
C21
R91
R34
R33
R45
OFF MAX
R92
R69
R41
R58
Q4
R66
LD1
S1
P3
LD19
LD2
LD3
R70R67
LD4
TB1 TB2
SW1
C8
R88
FIGURE 17:
LOCATION OF
SELECTABLE SWITCHES
LD13
PHOTO
CLOSE
ADJUSTMENT
FORCE
R30
R26
R29
COM
COM
COM
24V
AC
ALT
RDO
CRO
FRE
OPN
CLO
STO
COM
OPN
24V
AC
PHOTO
D12
R81
C25
C1TB1 C8
DRY CONTACTS
NORMALLY OPEN
IS REQUIRED FOR THE ENTRY SYSTEM
#0
*
987
6
5
4
3
21
NOTE: A DEDICATED POWER SUPPLY
WIRING PHONE ENTRY SYSTEM
Figure 16: Wiring an Access System
C: INSTALLING THE OPERATOR
15