Quick Start Manual

ManualsBrandsLinear ManualsMisc ElectronicsLinear DXS-31/ Supervised Universal Door/ Window Transmitter

DXS-31 Installation Instructions

Linear P/N: 212790 B

Material: 20 Lb. Mead Bond

Size: 8 1/2 x 11"

Ink: PMS 561 (Aqua)

2 of 2 (Back Side)

Scale: 1-1

TRANSMITTER MOUNTING ADJUSTING MAGNET HEIGHT

OPTION JUMPER POSITIONS CONNECTING EXTERNAL CONTACTS

CONNECTING EXTERNAL GLASS BREAK SENSOR PROGRAMMING RECEIVER

CHANGING BATTERIES LINEAR LIMITED WARRANTY

This Linear product is warranted against defects in material and workmanship for twelve (12) months. The Warranty Expiration Date

is labeled on the product.

This warranty extends only to wholesale customers

who buy direct from Linear or through Linear’s

normal distribution channels.

Linear does not warrant this product to consumers.

Consumers should inquire from their selling

dealer as to the nature of the dealer’s warranty, if any.

There are no obligations or liabilities on the part of Linear corporation

for consequential damages arising out of or in connection with use or performance of this product or other indirect damages

with respect to loss of property, revenue, or profit, or cost of removal, installation, or reinstallation.

All implied warranties,

including implied warranties for merchantability and implied warranties for fitness, are valid only until Warranty Expiration Date as

labeled on the product.

This Linear Corporation Warranty is in lieu of all other warranties express or implied.

For warranty service on Linear equipment return product, at sender’s expense to:

All products returned for warranty service require a Return Product Authorization Number (RPA#). Contact Linear Technical Services

at 1-800-421-1587 for an RPA# and other important details.

IMPORTANT !!!

Linear radio controls provide a reliable communications link and fill an important need in portable wireless signalling. However, there

are some limitations which must be observed.

✶

For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 15 devices. As such,

they have limited transmitter power and therefore limited range.

✶

A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals that occur on or

near their operating frequencies, regardless of code settings.

✶

Changes or modifications to the device may void FCC compliance.

✶

Infrequently used radio links should be tested regularly to protect against undetected interference or fault.

✶

A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or dealer, and these

facts should be communicated to the ultimate users.

ATTACH MOUNTING PLATES

USING THE SCREWS OR

DOUBLE-STICK TAPE PROVIDED

NOTE: ATTACHING THE TRANSMITTER WITH DOUBLE-STICK

TAPE IS NOT ALLOWED IN UL INSTALLATIONS

ADJUST MAGNET

HEIGHT UNTIL

CASE LEVELS

ARE ABOUT EQUAL

TRANSMITTER

CASE BOTTOM

MAGNET

THE SNAP-ON MAGNET SPACER

CAN BE USED TO ADD 1/4" HEIGHT

TO THE MAGNET (SPACERS CAN ALSO

BE SNAPPED TOGETHER FOR MORE LIFT)

SELECTS INTERNAL

SWITCH

(INSIDE POSITION)

SELECTS GLASS

BREAK SENSOR ONLY

(EDGE POSITION)

SELECTS EXTERNAL

SWITCH

(MIDDLE POSITION)

SELECTS BOTH

INTERNAL AND

EXTERNAL SWITCHES

(NO JUMPER)

NOTE: THE TWO

SWITCHES

ARE IN SERIES,

BOTH MUST BE

CLOSED TO

RESTORE LOOP

NOTE: GLASS

BREAK INPUT

TERMINALS ARE

ALWAYS ACTIVE

INPUT SELECT

JUMPER

INSTANT/

DELAY

SELECT

JUMPER

SELECTS

DELAY

SELECTS

INSTANT

CONNECT NORMALLY OPEN

GLASS BREAK SENSOR

WIRES TO TERMINALS 2 & 3

ROUTE SENSOR WIRES UP

THROUGH WIRING SLOT

NOTE: THIS

TRANSMITTER IS

DESIGNED FOR USE

WITH THE UNITED

SECURITY PRODUCTS

"WINDOW BUG" GLASS

BREAK SENSOR.

OTHER SENSORS

HAVE NOT BEEN

TESTED.

REMOVE JUMPER FROM

THESE PINS (SELECTS

INTERNAL SWITCH)

PLACE JUMPER ON THESE

PINS (SELECTS GLASS

BREAK SENSOR)

1. PLACE RECEIVER INTO

PROGRAM OR "LEARN" MODE

2. ACTIVATE TRANSMITTER

BY OPENING DOOR OR

WINDOW

3. VERIFY THAT THE

RECEIVER ACCEPTED THE

SIGNAL

4. REPLACE TRANSMITTER

COVER WHEN FINISHED

NOTE: THE TRANSMIT

INDICATOR WILL ONLY LIGHT

DURING TRANSMISSIONS

WHEN THE CASE IS OPEN

(EXCEPT WHEN PUSHING

THE CASE FOR TESTING)

OPEN DOOR, TRANSMIT

INDICATOR SHOULD LIGHT

WIRE EXTERNAL NORMALLY

CLOSED CONTACTS TO

TERMINALS 1 & 2

THIS IS THE FACTORY SET

JUMPER POSITION, IT

SELECTS THE INTERNAL

CONTACTS

PUT JUMPER ON THE

MIDDLE PINS TO USE

AN EXTERNAL SWITCH

- OR -

REMOVE JUMPER TO USE

BOTH EXTERNAL AND

INTERNAL SWITCHES

(SEE NOTE)

NOTE: THE TWO SWITCHES

ARE IN SERIES, BOTH MUST BE

CLOSED TO RESTORE LOOP

REDUCTION

RING

BATTERY

CLAMP

TWO TYPE 2032

BATTERIES

BATTERY

RETAINING

SCREW

SLIDE "T" END

OF CLAMP

THROUGH SLOT

WHEN THE TRANSMIT INDICATOR

BLINKS DURING TRANSMISSIONS

OR WHEN THE RECEIVER

INDICATES A LOW BATTERY, THE

BATTERIES NEED REPLACING

1. REMOVE THE BATTERY

RETAINING SCREW

2. REMOVE THE BATTERY CLAMP

3. REPLACE BATTERIES WITH TWO

TYPE 2032 BATTERIES (PLUS SIDE

UP)

4. REPLACE BATTERY CLAMP AND

RETAINING SCREW