Owner's Manual

ManualsBrandsLinear ManualsMisc ElectronicsLinear DXR-702/EC

INSTR,INSTL,DXR-702/EC

Linear P/N: 220095 A

Material: 20 Lb. Mead Bond

Size: 8.500" x 11.000"

Ink: Black

Scale: 1-1

Side 2 of 2

TERMINAL CONNECTIONS

BUTTON AND INDICATOR FUNCTIONS

FUNCTION PROGRAM BUTTONS

PROGRAM

INDICATOR

NORMAL

OPERATION

RELEASES LATCHED

RELAY FOR

CHANNEL 1 OR 2

LIGHTS WHEN

TRANSMITTER IS

RECEIVED,

FLASHES WHEN

INTERFERENCE IS

RECEIVED

PROGRAMMING

MEMORY

PRESS AND

RELEASE FOR

CHANNEL 1 OR 2

LIGHTS FOR 3

SECONDS FOR

PROGRAMMING

CHECKING

MEMORY

PRESS FOR

CHANNEL 1 OR 2

UNTIL BLINK AND

RELEASE

BLINKS THE

NUMBER OF

TRANSMITTERS IN

CHANNEL

MEMORY

ERASING

MEMORY

FOR CHANNEL 1 OR

2, PRESS AND HOLD

THROUGH THE

COUNT THEN HOLD

FOR 5 SECONDS

AFTER BLINKING

COUNT, A PAUSE

THEN A SINGLE

BLINK AS

MEMORY IS

ERASED (DOUBLE

BLINK ON

CHANNEL 2)

PROGRAMMING MEMORY CHECKING MEMORY

SYSTEM TESTING ERASING MEMORY INTERNATIONAL WARRANTY

This Linear product is warranted against defects in material and workmanship for twelve (12)

months. The Warranty Expiration Date is labeled on the product. This warranty extends only

to wholesale customers who buy direct from Linear or through Linear’s normal distribution

channels. Linear does not warrant this product to consumers. Consumers should inquire

from their selling dealer as to the nature of the dealer’s warranty, if any. There are no obligations

or liabilities on the part of Linear Corporation for consequential damages arising out of

or in connection with use or performance of this product or other indirect damages with

respect to loss of property, revenue, or profit, or cost of removal, installation, or

reinstallation. All implied warranties, including implied warranties for merchantability and

implied warranties for fitness, are valid only until Warranty Expiration Date as labeled on

the product. This Linear Corporation Warranty is in lieu of all other warranties express or

implied. For warranty service on Linear equipment return product, at sender’s expense

to:

Linear Hong Kong 19/F Hounor Industrial Centre, 6 Sun Yip StreetChai Wan, Hong Kong

Attention: Repairs Department

REPAIRS POLICY

Charges will be made for equipment that is not in warranty, shows customer abuse, or is damaged

by the effects of lightning, water, fire, or other abnormal happenings.

Customer’s equipment sent in for repair may be repaired or replaced with new or remanufactured

equipment at Linear’s discretion.

The customer is always responsible for shipping and handling charges to the repairs facility.

Linear will pay return shipping and handling charges on “in warranty” products shipped back to

the customer. The customer will be billed for the return shipping and handling charges on “out of

warranty” products.

There will be a 50% expedite fee for any express requests.

The International Sales Manager must be notified prior to the return of product to Linear. All

international returns must have an International Repair Authorization number (IRA#). The number

must be marked on all packages. Failure to do so will cause delays in processing.

IMPORTANT !!!

Linear radio controls provide a reliable communications link and fill an important need in portable

wireless signaling. However, there are some limitations which must be observed. The radios are

required to comply with local rules and regulations as radio devices. As such, they have limited

transmitter power and therefore limited range.

A receiver cannot respond to more than one transmitted signal at a time and may be blocked by

radio signals that occur on or near their operating frequencies, regardless of code settings.

Changes or modifications to the device may void regulatory compliance. Infrequently used radio

links should be tested regularly to protect against undetected interference or fault. A general

knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor

or dealer, and these facts should be communicated to the ultimate users.

N.O.

COM

N.C.

N.O.

COM

N.C.

N.O.

COM

N.C.

N.O.

COM

N.C.

N.O.

COM

N.C.

N.O.

COM

N.C.

N.O.

COM

N.C.

N.O.

COM

N.C.

N.O.

COM

N.C.

N.O.

COM

N.C.

N.O.

COM

N.C.

N.O.

COM

N.C.

DXR-702 TERMINALS DXR-702 TERMINALS

DXR-702 TERMINALS

ALARM PANEL CONNECTION WITH DOOR STATUS

LATCHING RELAY OPTION

ALARM

LOOP 1

N.C. OR N.O.

ALARM

LOOP 2

N.C. OR N.O.

NOTE:

LATCHING MODE

ALLOWS PANEL

TO SHOW DXT-31

DOOR STATUS

AUX.

POWER

ALARM

LOOP

N.C. OR N.O.

TROUBLE

LOOP

N.C. OR N.O.

AUX.

POWER

ALARM PANEL CONNECTION WITH LOW BATTERY REPORTING

LATCHING RELAY OPTION

NOTE:

CHANNEL 2 MUST

BE EMPTY TO

REPORT LOW

BATTERY

ALARM

LOOP 1

N.C. OR N.O.

ALARM

LOOP 2

N.C. OR N.O.

AUX.

POWER

ALARM PANEL CONNECTION FOR PANIC BUTTONS

1 SECOND RELAY OPTION

NOTE:

TRANSMITTERS

WILL AUTO

RESTORE AFTER

1 SECOND

RADIO

POWER

XFMR

AUX.

POWER

XFMR

ACCESS CONTROL CONNECTION

4 SECOND RELAY OPTION

BUZZER

DOOR

STRIKE

EXTERNAL

RELAY 1

LOAD

EXTERNAL

RELAY 2

LOAD

POWER

SUPPLY

EXTERNAL RELAY CONNECTION

TOGGLE RELAY OPTION

SECURITY CAMERA CONNECTION

LATCHING RELAY OPTION

CAMERA

& VCR

STILL

CAMERA

POWER

SUPPLY

1. PRESS AND RELEASE

PROGRAM BUTTON FOR THE

DESIRED CHANNEL.

2. PROGRAM INDICATOR WILL

LIGHT FOR 3 SECONDS IF

THERE IS ROOM IN THAT

CHANNEL'S MEMORY FOR

ANOTHER TRANSMITTER

(32 TRANSMITTERS MAXIMUM

TOTAL ALLOWED BETWEEN

BOTH CHANNELS IN THE

RECEIVER).

3. WITHIN 3 SECONDS, SEND

SIGNAL FROM TRANSMITTER,

PROGRAM INDICATOR WILL

FLICKER AS SIGNAL IS

RECEIVED.

4. REPEAT THE ABOVE THREE

STEPS FOR EACH

ADDITIONAL TRANSMITTER.

MULTI-CHANNEL

TRANSMITTER NOTE:

EACH RECEIVER CHANNEL CAN

ONLY BE PROGRAMMED TO

ACTIVATE FROM A SINGLE

BUTTON ON A MULTI-CHANNEL

TRANSMITTER. LEARNING THE

SAME BUTTON INTO BOTH

CHANNELS ACTIVATES CHANNEL

ONE ONLY.

AFTER PUSHING THE RECEIVER'S

PROGRAMMING BUTTON, YOU ONLY HAVE

3 SECONDS TO SEND A SIGNAL BEFORE

PROGRAMMING MODE STOPS

1. PRESS PROGRAM BUTTON FOR THE

DESIRED CHANNEL AND HOLD FOR ABOUT

TWO SECONDS UNTIL INDICATOR LIGHTS

THEN RELEASE.

2. COUNT THE NUMBER OF INDICATOR BLINKS,

THIS IS THE TOTAL NUMBER OF

TRANSMITTERS PROGRAMMED INTO THAT

CHANNEL.

PUSH UNTIL

INDICATOR LIGHTS

NOTE: DO NOT CONTINUE TO PRESS

BUTTON OR MEMORY WILL BE ERASED

1. ACTIVATE EACH TRANSMITTER,

ONE AT AT TIME.

2. LISTEN FOR RELAY CLICK IN

THE RECEIVER.

3. VERIFY THAT THE DEVICE CONNECTED

TO THE RECEIVER RESPONDS AND THAT

THE PROPER CHANNEL ACTIVATES.

4. TEST PORTABLE TRANSMITTERS IN

VARIOUS LOCATIONS TO DETERMINE

SYSTEM PERFORMANCE.

R&TTE VAEE 27840, EMC, SFT, ETS

Linear Corporation declares that the apparatus DXR-702/EC

complies with the essential requirements and other relevant

provisions of Directive 1995/5/EC.

1. PRESS PROGRAM BUTTON

FOR THE CHANNEL TO ERASE

AND CONTINUE TO HOLD IT

THROUGH THE COUNT OF THE

TRANSMITTERS.

2. CONTINUE TO HOLD THE

BUTTON AFTER THE COUNT

UNTIL THE INDICATOR BLINKS

ONCE FOR CHANNEL ONE,

TWICE FOR CHANNEL TWO

(ABOUT FIVE SECONDS

AFTER THE COUNT).

3. ALL TRANSMITTERS

PROGRAMMED INTO

THAT CHANNEL

WILL BE ERASED.

PUSH AND HOLD BUTTON

FOR FIVE SECONDS AFTER

THE TRANSMITTER COUNT