Owner's Manual

Black 0001
Black0001
INSTR, INST, AE-2, MECH ELECT Linear P/N: 215314 C Material: 20 Lb. Mead Bond Size: 8.500" x 11.000" Ink: Black Scale: 1-1 Front Side 1 of 2
AE-2
Telephone Entry Control Console
Mechanical & Electrical
Installation Instructions
[phone] • FAX [phone]
USA & Canada [phone] & [phone]
Toll Free FAX [phone]
www.linearcorp.com
INTRODUCTION
The Model AE-2 Telephone Entry Control Console is designed for use as a primary
access control device for gated communities, parking garages, office buildings,
apartments, dormitories, hotels/motels, commercial buildings and recreational facilities.
This unit is a fusion of Linear’s full-featured Model AM/II Access Control System and
the Model AE-2 Telephone Entry Module. Housed in a locked, rugged stainless steel
enclosure, the AE-2 features a 12-key telephone style keypad, a vacuum florescent
two-line directory display, and a built-in microphone and speaker.
All of the outstanding AM/II access control system functions are available with the AE-2 in
addition to hands-free, full duplex telephone communications with tenants or authorized
personnel for granting access. Entry codes can also be typed directly on the keypad.
In a typical installation, the unit’s memory would be programmed with each tenant’s
name and directory code number. A visitor would use the
*
or # key on the AE-2 to
view the directory names and code number for the desired party. Upon entering the
directory number, the AE-2 will automatically dial the tenant’s telephone number and
establish two-way voice communication between the visitor and the tenant. The tenant
will then have the option to grant access to the guest by pressing a digit on their telephone.
In addition to the telephone entry, the AE-2 can grant access using various remote
devices that are commonly used with the AM/II. These devices include wireless
transmitters, proximity receivers, swipe card readers and remote keypads.
The output relays can be programmed to control electric door strikes, door & gate
operators, barrier gates. CCTV cameras can also be triggered by the output relays to
monitor the entry areas.
All of the programming functions of the AE-2 can be performed directly through the
unit’s keypad. An optional telephone modem can be installed for easy remote
programming with a personal computer.
The AE-2 cabinet has provisions for installing a postal lock for keyed mail carrier access.
The postal lock can be programmed to activate any of the four output relays.
1. SYSTEM COMPONENT LOCATIONS
2. AE-2 COMPONENT LOCATIONS 3. DETERMINE MOUNTING LOCATION 4. MOUNT CABINET
MODULAR
TELEPHONE
JACK (HIDDEN)
TELEPHONE
LINE TERMINALS
HYBRID LEVEL
ADJUSTMENT
(FACTORY SET
DO NOT ADJUST)
SPEAKER
VOLUME
ADJUSTMENT
AE-2 TO AM/II
INTERCONNECT
CABLE
ON-LINE INDICATOR
(LIGHTS WHEN PHONE
LINE IS ACTIVE)
DISPLAY
CONTRAST
ADJUSTMENT
(NOT USED ON
THIS MODEL)
SPEAKER
CONNECTOR
TEST JUMPER
(REMOVE TO
HEAR UNIT DIAL)
MICROPHONE
& POSTAL KEY
SWITCH TERMINALS
BUSY INDICATOR
(LIGHTS WHEN AE-2 IS
COMMUNICATING OR WHEN
PHONE LINE IS DISCONNECTED)
THE AE-2 SHOULD BE MOUNTED IN A WELL LIT LOCATION NEAR THE
CONTROLLED OPENING. WIRING ACCESS FOR POWER, TELEPHONE,
EARTH GROUND, CONTROL OUTPUT AND ANTENNA CO-AX MUST BE
AVAILABLE BEHIND THE MOUNTING LOCATION.
AE-2
TELEPHONE
ENTRY SYSTEM
CONTROLLED
ENTRY DOOR
AREA
LIGHTING
5 3/8" 5 3/8"
9 3/8"
5 3/8" 5 3/8"
MOUNT CABINET WITH
SUITABLE HARDWARE FOR
MOUNTING SURFACE.
USE TOGGLE BOLTS FOR
STUCCO WALL, WEDGE
ANCHORS OR EXPANSION
BOLTS FOR CONCRETE
WALL, LAG SCREWS FOR
WOOD WALL.
MOUNTING
LOCATION