Datasheet
LTC6090
3
6090fa
elecTrical characTerisTics
The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at T
J
= 25°C. Test conditions are V
+
= 70V, V
–
= –70V, V
CM
= V
OUT
= 0V, V
OD
= Open
unless otherwise noted.
orDer inForMaTion
LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION JUNCTION TEMPERATURE RANGE
LTC6090CS8E#PBF LTC6090CS8E#TRPBF 6090 8-Lead Plastic SO 0°C to 70°C
LTC6090IS8E#PBF LTC6090IS8E#TRPBF 6090 8-Lead Plastic SO –40°C to 85°C
LTC6090HS8E#PBF LTC6090HS8E#TRPBF 6090 8-Lead Plastic SO –40°C to 125°C
LTC6090CFE#PBF LTC6090CFE#TRPBF 6090FE 16-Lead Plastic TSSOP 0°C to 70°C
LTC6090IFE#PBF LTC6090IFE#TRPBF 6090FE 16-Lead Plastic TSSOP –40°C to 85°C
LTC6090HFE#PBF LTC6090HFE#TRPBF 6090FE 16-Lead Plastic TSSOP –40°C to 125°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
Consult LTC Marketing for information on non-standard lead based finish parts.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/
C-, I-SUFFIXES H-SUFFIX
SYMBOL PARAMETER CONDITIONS MIN TYP MAX MIN TYP MAX UNITS
V
OS
Input Offset Voltage
l
±330
±330
±1000
±1600
±330
±330
±1000
±1600
μV
μV
∆V
OS
/∆T Input Offset Voltage Drift
l
4 4 µV/°C
I
B
Input Bias Current (Note 6) Supply Voltage = ±70V
Supply Voltage = ±15V
Supply Voltage = ±15V
l
3
3
50
3
3
800
pA
pA
pA
I
OS
Input Offset Current (Note 6) Supply Voltage = ±15V
l
0.5
30
0.5
120
pA
pA
e
n
Input Noise Voltage Density f = 1kHz
f = 10kHz
14
11
14
11
nV/√Hz
nV/√Hz
Input Noise Voltage 0.1Hz to 10Hz 3.5 3.5 µV
P-P
i
n
Input Noise Current Density 1 1 fA/√Hz
V
CM
Input Common Mode Range Guaranteed by CMRR
l
V
–
+3V
±68
V
+
–3V
V
–
+3V
±68
V
+
–3V
V
V
C
IN
Common Mode Input
Capacitance
9 9 pF
C
DIFF
Differential Input Capacitance 5 5 pF
CMRR Common Mode Rejection Ratio V
CM
= –67V to 67V
l
105
100
125 105
100
125 dB
dB
PSRR Power Supply Rejection Ratio V
S
= ±4.75V to ±70V
l
105
100
118 105
100
118 dB
dB
V
OUT
Output Voltage Swing High
(Referred to V
+
)
No Load
I
SOURCE
= 1mA
I
SOURCE
= 10mA
l
l
l
25
100
750
50
200
1500
25
100
750
50
200
1500
mV
mV
mV
Output Voltage Swing Low
(Referred to V
–
)
No Load
I
SINK
= 1mA
I
SINK
= 10mA
l
l
l
10
40
250
25
80
600
10
40
250
25
80
600
mV
mV
mV
A
VOL
Large-Signal Voltage Gain R
L
= 10k,
V
OUT
from –60V to 60V
l
500
400
12000 500
400
12000 V/mV
V/mV