Datasheet
LTC3890-1
21
38901fb
APPLICATIONS INFORMATION
pin is less than 4.7V, the V
IN
LDO is enabled. Power dis-
sipation for the IC in this case is highest and is equal to
V
IN
• I
INTVCC
. The gate charge current is dependent on
operating frequency as discussed in the Efficiency Con-
siderations section. The junction temperature can be
estimated by using the equations given in Note 3 of the
Electrical Characteristics. For example, the LTC3890-1
INTV
CC
current is limited to less than 15mA from a 40V
supply when not using the EXTV
CC
supply at 70°C ambi-
ent temperature:
T
J
= 70°C + (15mA)(40V)(90°C/W) = 125°C
To prevent the maximum junction temperature from be-
ing exceeded, the input supply current must be checked
while operating in forced continuous mode (PLLIN/MODE
= INTV
CC
) at maximum V
IN
.
When the voltage applied to EXTV
CC
rises above 4.7V, the
V
IN
LDO is turned off and the EXTV
CC
LDO is enabled. The
EXTV
CC
LDO remains on as long as the voltage applied to
EXTV
CC
remains above 4.5V. The EXTV
CC
LDO attempts
to regulate the INTV
CC
voltage to 5.1V, so while EXTV
CC
is less than 5.1V, the LDO is in dropout and the INTV
CC
voltage is approximately equal to EXTV
CC
. When EXTV
CC
is greater than 5.1V, up to an absolute maximum of 14V,
INTV
CC
is regulated to 5.1V.
Using the EXTV
CC
LDO allows the MOSFET driver and
control power to be derived from one of the LTC3890-1’s
switching regulator outputs (4.7V ≤ V
OUT
≤ 14V) during
normal operation and from the V
IN
LDO when the out-
put is out of regulation (e.g., start-up, short-circuit). If
more current is required through the EXTV
CC
LDO than
is specified, an external Schottky diode can be added
between the EXTV
CC
and INTV
CC
pins. In this case, do
not apply more than 6V to the EXTV
CC
pin and make sure
that EXTV
CC
≤ V
IN
.
Significant efficiency and thermal gains can be realized
by powering INTV
CC
from the output, since the V
IN
cur-
rent resulting from the driver and control currents will be
scaled by a factor of (Duty Cycle)/(Switcher Efficiency).
For 5V to 14V regulator outputs, this means connecting
the EXTV
CC
pin directly to V
OUT
. Tying the EXTV
CC
pin to
an 8.5V supply reduces the junction temperature in the
previous example from 125°C to:
T
J
= 70°C + (15mA)(8.5V)(90°C/W) = 82°C
However, for 3.3V and other low voltage outputs, additional
circuitry is required to derive INTV
CC
power from the output.
The following list summarizes the four possible connec-
tions for EXTV
CC
:
1. EXTV
CC
Grounded. This will cause INTV
CC
to be powered
from the internal 5.1V regulator resulting in an efficiency
penalty of up to 10% at high input voltages.
2. EXTV
CC
Connected directly to V
OUT
. This is the normal
connection for a 5V to 14V regulator and provides the
highest efficiency.
3.
EXTV
CC
Connected to an External supply. If an external
supply is available in the 5V to 14V range, it may be
used to power EXTV
CC
providing it is compatible with
the MOSFET gate drive requirements. Ensure that
EXTV
CC
< V
IN
.
4. EXTV
CC
Connected to an Output-Derived Boost Network.
For 3.3V and other low voltage regulators, efficiency
gains can still be realized by connecting EXTV
CC
to an
output-derived voltage that has been boosted to greater
than 4.7V. This can be done with the capacitive charge
pump shown in Figure 9. Ensure that EXTV
CC
< V
IN
.
EXTV
CC
V
IN
TG1
SW
BG1
PGND
1/2 LTC3890-1
R
SENSE
V
OUT
NDS7002
C
OUT
38901 F09
MBOT
MTOP
C
IN
L
D
BAT85 BAT85
BAT85
Figure 9. Capacitive Charge Pump for EXTV
CC