Datasheet

LTC3868-1
20
38681fd
APPLICATIONS INFORMATION
Figure 6. Setting Output Voltage
Equation 1 has a maximum at V
IN
= 2V
OUT
, where I
RMS
= I
OUT
/2. This simple worst-case condition is commonly
used for design because even signifi cant deviations do not
offer much relief. Note that capacitor manufacturers’ ripple
current ratings are often based on only 2000 hours of life.
This makes it advisable to further derate the capacitor, or
to choose a capacitor rated at a higher temperature than
required. Several capacitors may be paralleled to meet
size or height requirements in the design. Due to the high
operating frequency of the LTC3868-1, ceramic capacitors
can also be used for C
IN
. Always consult the manufacturer
if there is any question.
The benefi t of the LTC3868-1 2-phase operation can be
calculated by using Equation 1 for the higher power control-
ler and then calculating the loss that would have resulted
if both controller channels switched on at the same time.
The total RMS power lost is lower when both controllers
are operating due to the reduced overlap of current pulses
required through the input capacitor’s ESR. This is why
the input capacitor’s requirement calculated above for the
worst-case controller is adequate for the dual controller
design. Also, the input protection fuse resistance, battery
resistance, and PC board trace resistance losses are also
reduced due to the reduced peak currents in a 2-phase
system. The overall benefi t of a multiphase design will
only be fully realized when the source impedance of the
power supply/battery is included in the effi ciency testing.
The sources of the top MOSFETs should be placed within
1cm of each other and share a common C
IN
(s). Separating
the sources and C
IN
may produce undesirable voltage and
current resonances at V
IN
.
A small (0.1µF to 1µF) bypass capacitor between the chip
V
IN
pin and ground, placed close to the LTC3868-1, is
also suggested. A 10 resistor placed between C
IN
(C1)
and the V
IN
pin provides further isolation between the
two channels.
The selection of C
OUT
is driven by the effective series
resistance (ESR). Typically, once the ESR requirement
is satisfi ed, the capacitance is adequate for fi ltering. The
output ripple (∆V
OUT
) is approximated by:
ΔV
OUT
≈ΔI
L
ESR+
1
8•f•C
OUT
⎛
⎝
⎜
⎞
⎠
⎟
where f is the operating frequency, C
OUT
is the output
capacitance and ∆I
L
is the ripple current in the inductor.
The output ripple is highest at maximum input voltage
since ∆I
L
increases with input voltage.
Setting Output Voltage
The LTC3868-1 output voltages are each set by an exter-
nal feedback resistor divider carefully placed across the
output, as shown in Figure 6. The regulated output voltage
is determined by:
V
OUT
= 0.8V 1+
R
B
R
A
⎛
⎝
⎜
⎞
⎠
⎟
To improve the frequency response, a feedforward ca-
pacitor, C
FF
, may be used. Great care should be taken to
route the V
FB
line away from noise sources, such as the
inductor or the SW line.
1/2 LTC3868-1
V
FB
V
OUT
R
B
C
FF
R
A
38681 F05
Soft-Start (SS Pins)
The start-up of each V
OUT
is controlled by the voltage on
the respective SS pin. When the voltage on the SS pin
is less than the internal 0.8V reference, the LTC3868-1
regulates the V
FB
pin voltage to the voltage on the SS pin
instead of 0.8V. The SS pin can be used to program an
external soft-start function.
Soft-start is enabled by simply connecting a capacitor from
the SS pin to ground, as shown in Figure 7. An internal
1µA current source charges the capacitor, providing a
1/2 LTC3868-1
SS
C
SS
SGND
38681 F06
Figure 7. Using the SS Pin to Program Soft-Start