Datasheet

LTC3838
28
3838fa
APPLICATIONS INFORMATION
and BOOST capacitor under all operating conditions. Vari-
able frequency in response to load steps offers superior
transient performance but requires higher instantaneous
gate drive. Gate charge demands are greatest in high
frequency low duty factor applications under high load
steps and at start-up.
DRV
CC
Regulator and EXTV
CC
Power
The LTC3838 features a PMOS low dropout (LDO) linear
regulator that supplies power to DRV
CC
from the V
IN
supply.
The LDO regulates its output at the DRV
CC1
pin to 5.3V.
The LDO can supply a maximum current of 100mA and
must be bypassed to ground with a minimum of 4.7µF
ceramic capacitor. Good bypassing is needed to supply
the high transient currents required by the MOSFET gate
drivers and to minimize interaction between the channels.
High input voltage applications in which large MOSFETs
are being driven at high frequencies may cause the maxi-
mum junction temperature rating for the LTC3838 to be
exceeded, especially if the LDO is active and provides
DRV
CC
. Power dissipation for the IC in this case is high-
est and is approximately equal to V
IN
• I
DRVCC
. The gate
charge current is dependent on operating frequency as
discussed in the Efficiency Considerations section. The
junction temperature can be estimated by using the equa-
tion given in Note 2 of the Electrical Characteristics. For
example, when using the LDO, LTC3838’s DRV
CC
current
is limited to less than 52mA from a 38V supply at T
A
=
70°C in the FE package:
T
J
= 70°C + (52mA)(38V)(28°C/W) = 125°C
To prevent the maximum junction temperature from being
exceeded, the input supply current must be checked while
operating in continuous conduction mode at maximum V
IN
.
When the voltage applied to the EXTV
CC
pin rises above
the switchover voltage (typically 4.6V), the V
IN
LDO is
turned off and the EXTV
CC
is connected to DRV
CC2
pin with
an internal switch. This switch remains on as long as the
voltage applied to EXTV
CC
remains above the hysteresis
(around 200mV) below the switchover voltage. Using
EXTV
CC
allows the MOSFET driver and control power to
be derived from the LTC3838’s switching regulator output
V
OUT
during normal operation and from the LDO when the
output is out of regulation (e.g., start up, short circuit). If
more current is required through the EXTV
CC
than is speci-
fied, an external Schottky diode can be added between the
EXTV
CC
and DRV
CC
pins. Do not apply more than 6V to the
EXTV
CC
pin and make sure that EXTV
CC
is less than V
IN
.
Significant efficiency and thermal gains can be realized
by powering DRV
CC
from the switching converter output,
since the V
IN
current resulting from the driver and control
currents will be scaled by a factor of (Duty Cycle)/(Switcher
Efficiency).
Tying the EXTV
CC
pin to a 5V supply reduces the junction
temperature in the previous example from 125°C to:
T
J
= 70°C + (52mA)(5V)(28°C/W) = 77°C
However, for 3.3V and other low voltage outputs, ad-
ditional circuitry is required to derive DRV
CC
power from
the converter output.
The following list summarizes the four possible connec-
tions for EXTV
CC
:
1. EXTV
CC
left open (or grounded). This will cause INTV
CC
to be powered from the internal 5.3V LDO resulting
in an efficiency penalty of up to 10% at high input
voltages.
2. EXTV
CC
connected directly to switching converter output
V
OUT
is higher than the switchover voltage’s higher limit
(4.8V). This provides the highest efficiency.
3. EXTV
CC
connected to an external supply. If a 4.8V or
greater external supply is available, it may be used to
power EXTV
CC
providing that the external supply is
sufficient for MOSFET gate drive requirements.
4. EXTV
CC
connected to an output-derived boost network.
For 3.3V and other low voltage converters, efficiency
gains can still be realized by connecting EXTV
CC
to an
output-derived voltage that has been boosted to greater
than 4.8V.