Datasheet

LTC3707-SYNC
18
3707sfa
than 4.7V. This can be done with either the inductive boost
winding as shown in Figure 6a or the capacitive charge
pump shown in Figure 6b. The charge pump has the
advantage of simple magnetics.
Topside MOSFET Driver Supply (C
B
, D
B
)
External bootstrap capacitors C
B
connected to the BOOST
pins supply the gate drive voltages for the topside MOSFETs.
Capacitor C
B
in the functional diagram is charged though
external diode D
B
from INTV
CC
when the SW pin is low.
When one of the topside MOSFETs is to be turned on,
the driver places the C
B
voltage across the gate-source
of the desired MOSFET. This enhances the MOSFET and
turns on the topside switch. The switch node voltage, SW,
rises to V
IN
and the BOOST pin follows. With the topside
MOSFET on, the boost voltage is above the input supply:
V
BOOST
= V
IN
+ V
INTVCC
. The value of the boost capacitor
C
B
needs to be 100 times that of the total input capacitance
of the topside MOSFET(s). The reverse breakdown of the
external Schottky diode must be greater than V
IN(MAX)
.
When adjusting the gate drive level, the fi nal arbiter is the
total input current for the regulator. If a change is made
and the input current decreases, then the effi ciency has
improved. If there is no change in input current, then there
is no change in effi ciency.
APPLICATIONS INFORMATION
Output Voltage
The IC output voltages are each set by an external feedback
resistive divider carefully placed across the output capacitor.
The resultant feedback signal is compared with the internal
precision 0.800V voltage reference by the error amplifi er.
The output voltage is given by the equation:
VV
R
R
OUT
=+
⎛
⎝
⎜
⎞
⎠
⎟
08 1
2
1
.
where R1 and R2 are defi ned in Figure 2.
SENSE
+
/SENSE
–
Pins
The common mode input range of the current comparator
sense pins is from 0V to (1.1)INTV
CC
. Continuous linear
operation is guaranteed throughout this range allowing
output voltage setting from 0.8V to 7.7V, depending upon
the voltage applied to EXTV
CC
. A differential NPN input
stage is biased with internal resistors from an internal 2.4V
source as shown in the Functional Diagram. This requires
that current either be sourced or sunk from the SENSE
pins depending on the output voltage. If the output voltage
is below 2.4V current will fl ow out of both SENSE pins to
the main output. The output can be easily preloaded by
Figure 6a. Secondary Output Loop and EXTV
CC
Connection
EXTV
CC
FCB
SGND
V
IN
TG1
SW
BG1
PGND
LTC3707-SYNC
R
SENSE
V
OUT
V
SEC
+
C
OUT
+
1μF
3707 F06a
N-CH
N-CH
R6
+
C
IN
V
IN
T1
1:N
OPTIONAL EXTV
CC
CONNECTION
5V < V
SEC
< 7V
R5
Figure 6b. Capacitive Charge Pump for EXTV
CC
EXTV
CC
V
IN
TG1
SW
BG1
PGND
LTC3707-SYNC
R
SENSE
V
OUT
VN2222LL
+
C
OUT
3707 F06b
N-CH
N-CH
+
C
IN
+
1μF
V
IN
L1
BAT85 BAT85
BAT85
0.22μF