Datasheet
12
LTC1686/LTC1687
LINEAR TECHNOLOGY CORPORATION 1997
16867fs, sn16867 LT/TP 1197 4K • PRINTED IN THE USA
Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
●
(408) 432-1900
FAX: (408) 434-0507
●
TELEX: 499-3977
●
www.linear-tech.com
Long traces bounded by a V
DD
and/or GND planes can add
substantial parasitic capacitance. Parasitic capacitances
on the receiver/driver outputs can also unduly slow down
both the propagation delay and the rise/fall times.
APPLICATIONS INFORMATION
WUU
U
The receiver inputs are high bandwidth and high imped-
ance. If they are left floating, any capacitive coupling from
any other signal can cause a glitch at the receiver output.
Thus, if the receiver is not being used, it is advisable to
always ground at least one of the two receiver input pins.
PACKAGE DESCRIPTION
U
Dimensions in inches (millimeters) unless otherwise noted.
S8 Package
8-Lead Plastic Small Outline (Narrow 0.150)
(LTC DWG # 05-08-1610)
PART NUMBER DESCRIPTION COMMENTS
LTC490 Low Power RS485 Full-Duplex Transceiver I
CC
= 300µA (Typ), SO-8 Package
LTC491 Low Power RS485 Full-Duplex Transceiver I
CC
= 300µA (Typ), 14-Lead SO Package
LTC1518 High Speed Quad RS485 Receiver 52Mbps, Pin Compatible with LTC488
LTC1519 High Speed Quad RS485 Receiver 52Mbps, Pin Compatible with LTC489
LTC1520 High Speed Quad Differential Receiver 52Mbps, ±100mV Threshold, Rail-to-Rail Common Mode
LTC1685 High Speed RS485 Transceiver 52Mbps, Pin Compatible with LTC485
RELATED PARTS
SO8 0996
0.016 – 0.050
0.406 – 1.270
0.010 – 0.020
(0.254 – 0.508)
× 45°
0°– 8° TYP
0.008 – 0.010
(0.203 – 0.254)
0.053 – 0.069
(1.346 – 1.752)
0.014 – 0.019
(0.355 – 0.483)
0.004 – 0.010
(0.101 – 0.254)
0.050
(1.270)
TYP
1
2
3
4
0.150 – 0.157**
(3.810 – 3.988)
8
7
6
5
0.189 – 0.197*
(4.801 – 5.004)
0.228 – 0.244
(5.791 – 6.197)
DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD
FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE
*
**
S Package
14-Lead Plastic Small Outline (Narrow 0.150)
(LTC DWG # 05-08-1610)
S14 0695
1
2
3
4
0.150 – 0.157**
(3.810 – 3.988)
14
13
0.337 – 0.344*
(8.560 – 8.738)
0.228 – 0.244
(5.791 – 6.197)
12
11
10
9
5
6
7
8
0.016 – 0.050
0.406 – 1.270
0.010 – 0.020
(0.254 – 0.508)
× 45°
0° – 8° TYP
0.008 – 0.010
(0.203 – 0.254)
0.053 – 0.069
(1.346 – 1.752)
0.014 – 0.019
(0.355 – 0.483)
0.004 – 0.010
(0.101 – 0.254)
0.050
(1.270)
TYP
DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE
*
**